- Home & Workshop Products
Power is transmitted from the 1000-rpm tractor (1-3/4-in.) PTO through a central gearcase to the twin rear-mounted cutterbars.
Forming shields are easily adjusted to control material flow. This allows the operator to match the windrow width to harvesting requirements.
The forming shields are easily adjusted to match harvest requirements. No tools are required to adjust the forming shields. Windrow width on each unit can be adjusted from 1.2 to 2.5 m (3 ft, 11 in. to 8 ft, 2 in.).
A widespread kit is available as a field-installed bundle. The bundle consists of vanes that are installed behind the conditioning hood. The windrow width when using the widespread kit can be adjusted to be approximately the same as the cutting width of the platform.
Each cutting unit is equipped with 54 free-swinging, steel impeller tines. This John Deere conditioner provides excellent conditioning performance and fluffy windrows.
Impeller conditioning is standard equipment on all John Deere mower-conditioners.
Proper conditioning in a wide range of crops can be achieved when the conditioner is properly adjusted.
The impeller conditioner works well in legumes, especially alfalfa and most all-grass crops. Impeller conditioners are not recommended for thick-stemmed or cane-type crops, such as sudan or sudex, or crops over 5-ft tall.
The speed at which the tines rotate will also affect the degree of conditioning. Two impeller speeds can be achieved by interchanging the upper sheave and the lower sheave.
The simple to operate control panel enables the operator to easily operate all of the hydraulic functions of the 388 Twin Rear-Mounted Mower-Conditioner.
Features/functions of the control panel include:
With the power switch on, the zone selector switch (yellow circle) determines which functions are active by powering either Zone 1 or Zone 2.
With the zone selector switch moved to activate Zone 1 the operator can fold the 388 Twin Rear-Mounted Mower-Conditioner into transport position or adjust the cutterbar flotation on either the front or rear cutterbars.
Zone 2 is the primary setting for field operation. The three-position switch in Zone 2 is used to select the headland turn or working position of the rear cutting units. The position of the switch will determine which cutting platform or both will be raised
The 388 Twin Rear-Mounted Mower Conditioner is matched with a 131 Front-Mounted Mower-Conditioner to make what is commonly called a Triple-Mounted Mower-Conditioner (TMMC). This combination cuts nearly 8.73 m (28 ft, 8 in.) but can easily be converted to a narrow transport width of 3.1 m (10 ft, 2 in.).
To prepare for transporting, the side curtains of the 131 Front-Mounted Mower-Conditioner are unlocked and folded into the transport position. This will reduce the overall width during transport. The transport lock lever on the 131 Front-Mounted Mower-Conditioner is engaged so that side-to-side oscillation during transport is eliminated.
The side curtains are unlocked and pinned to reduce the overall transport height of the TMMC. The side curtain support provides rigidity to the side curtains during cutting and is folded down in transport to reduce the overall height.
Using the control panel configured to headland turn (switch in yellow circle moved to RH, Zone 2 switch centered), the operator uses the tractor hydraulics to raise the platforms. The mower-conditioner frame should be centered in preparation for transport.
Rear three-point hitch may be adjusted, as necessary, to assure the overall height of the mower-conditioner does not exceed 4.0 m (13 ft, 1 in.).
A spring-loaded safety lock secures the mower-conditioner in the raised position.
To prepare for field operation, the rope connected to the safety lock on the 388 Twin Rear-Mounted Mower-Conditioner is held while the platforms are partially lowered (rope can be released as soon as mower-conditioner is unlatched), using the control panel and tractor SCV.
The balance of the procedure above is reversed to continue on to field operation.
Flotation is controlled by accumulators on both the right-hand and left-hand cutting platforms. The easy to read gauges (one for each cutting platform) enable the operator to easily adjust the float pressure to the desired level.
A ball valve by the pressure gauge is opened and by using the control panel mounted in the tractor and the tractor selective control valve (SCV), the pressure can be adjusted to meet varying ground or crop conditions.
The control panel is used to adjust flotation of both the rear cutting platforms as well as the 131 Front-Mounted Mower-Conditioner.
|Select up to 4 models to compare specifications||
Rear Mount Mower-Conditioner
|PTO speed||1,000 rpm|
|HP 540 rpm PTO|
|HP 1000 rpm 1-3/8 in. PTO|
|HP 1000 rpm 1-3/4 in. PTO||With 131 Front-Mounted Mower-Conditioner: 147 kW
|Hydraulic pressure required|
|Cutting width||With 131 Front Mounted Mower-Conditioner: 8.7 m
|Cutting height||3-8 cm
|Number of disks||8 per unit|
|Number of knives||16 per unit|
|Disk speed||2,986 rpm|
|Knife tip speed|
|Lubrication||GL-5 gear lubricant|
|Oil reservoir capacity||2.25 L
0.59 U.S. gal.
|Cutterbar oil check||Fill plug|
|Angle adjustment||Tractor center link|
|Cutterbar protection||Shear shaft|
|Adjustable gauge shoes|
104 in.Number of V-tines
54 per unitNumber of speeds
Belt and sheavesConditioner hood
|Standard hitch||Tractor 3-point|
|Ball joint equal angle hitch|
|Rockshaft swivel hitch|
|Drawbar swivel hitch|
|Weight||With impeller conditioner
|Are wrenches required for adjusting?||Float