X570Lawn Tractor with 48-in. Deck

The tractor is powered by a John Deere iTorque™ power system, a combination of engine features and an exclusive hood design providing superior lugging ability, even cooling, and durability. Key engine features include:

• 24 hp (17.9 kW)
• Large 726 cc displacement
• V-twin air-cooled design 
  • Excellent power and performance
  • Smooth, quiet power
  • Easy starts
• Quality features include:
  • Cast-iron cylinder liners
  • Overhead valves
  • Full-pressure lubrication
  • Replaceable oil filter
  • Dual-stage air cleaner
• Solenoid-shift starter for easy starts, even in cold weather

Flywheel alternator

A flywheel alternator provides plenty of capacity to quickly recharge the battery and power electrical equipment, such as lights or a sprayer:

• 15-amp capacity
• Regulated to keep the battery at a full charge, without risk of overcharging

A heavy-duty sector and pinion steering system with quality bearings provides easy and precise control for the life of the tractor:

• Tight, 22-in. (56-cm) turning radius provides excellent maneuverability.
• Tight turning ability improves mowing efficiency.

Easy steering

Easy steering is important to give the operator an enjoyable mowing experience:

• Larger, 14-in. (35.6-cm) diameter steering wheel improves leverage for easier turns.
• Larger sector gear improves (increases) the steering ratio.
  • Higher steering ratio equals lower steering effort
• Dual drag links help equalize steering loads and greatly reduce steering error.
• Ball joints are provided on both ends of the steering tie rods.
• Long steering arms improve the mechanical advantage of the steering system though the full range of motion.
• Steering wheel/pinion gear shaft turns on a sealed ball bearing at the pinion gear.
  •  Gives easy steering
  •  Long steering system life
• Sector gear pivots on a shaft rather than a bushing to ensure proper gear mesh and eliminate binding.
• Upper and lower ends of the sector-gear shaft pivot on sealed ball bearings.
  • Reduce steering effort
  • Provide a smooth feel for the life of the tractor
• Greaseable front steering spindles pivot on heat-treated bushings.
  • Reduce friction for easier steering
  • Improve wear over time

The 48-in. (122-cm) Accel Deep Mower Deck is a stamped-steel, deep, flat-top design that delivers excellent cut quality, productivity, cleanliness, durability, and versatility. Optimal performance and dispersion of clippings is provided, even at faster mowing speeds:

• 4.83-in. (12.3-cm) depth throughout the entire deck shell for optimum mowing, mulching, and bagging performance
  • Optional MulchControl™ attachment provides superior mulching performance and versatility.
• Stamped-steel design eliminates sharp edges and corners where material can build up and diminish mowing performance
• Mower deck is suspended from the vehicle for a smooth and level cut
  • Adjustable mower wheels, positioned just above ground level, help reduce scalping

Excellent cut quality

Deep mower-deck stamping gives excellent cut quality. It allows the cut and suspended material room to exit the deck without getting recut:

• Reducing the amount of re-cutting enables more power to be used to cut incoming grass, which greatly improves mower capacity.
  • Helps maintain excellent cut quality at faster mowing speeds
• Clean flow of material out of discharge area prevents cut material from interfering with cutting the incoming grass, making it possible for the blades to cut incoming material cleanly.
• Even in mulching mode, cut evenness is improved compared to other designs because the additional depth allows for continuous circulation, optimal re-cutting, and an even distribution of clippings.

Productivity - getting the job done fast

Deep mower-deck stamping gives high productivity, which gets the job done fast. It allows the cut and suspended material room to exit the deck quickly, reducing the amount of re-cutting so more power is available to process incoming grass:

• Greatly improves mowers capacity to maintain excellent mowing performance in difficult mowing conditions and at higher speeds

Large discharge opening is both high and wide to handle more material:

• Gives a smooth, even discharge of clippings at all mowing speeds
• Reduces the chance of plugging, especially important when operating in wet, thick, or dense grass and when bagging
• The 48A Power Flow™ blower has an inlet housing with over 50 percent greater area than the 48X Power Flow blower used on previous machines.

Cleanliness - for the mower and the operator

The flat-top shape of the deck stamping is optimal for keeping itself and the operator clean:

• There are few places to catch and hold material on top and underneath the deck.
  • Top of deck stays cleaner, reducing time and effort needed for cleaning and service
  • Underside of deck is self-cleaning to maintain optimum performance without build-up of material to interfere with the flow of air and clippings
  • Less need to clean and remove build-up of material from underside deck
• The depth of the Accel Deep mower deck minimizes the amount of material that escapes from the front of the deck
  • Limited amount of material to drift onto the operator and mower deck
  • Even for material discharged out the chute, less re-cutting results in larger pieces that are less likely to end up on the operator
  • Mulching prevents the discharge of material completely and the MulchControl attachment makes mulching a practical solution for most mowing situations.

Cleaning a mower deck, both top and bottom, is one of the most frequent maintenance activities:

• The flat-top design reduces places for material to build up and makes material that does collect easy to remove.

A wash port is provided to make cleaning the underside of the mower deck easy.

• Hose connector is included with the mower deck.

Superior durability is designed in

The 48A Mower Deck has strong spindle pockets, to keep the blades aligned, even after years of tough service:

• Ribs in the deck shell add strength where it is needed.
• The 48A has a 23 percent heavier overall weight than the Edge™ Xtra 48-in. (122-cm) mower deck used on previous machines.

Mower wheels are heavy duty:

• Provides greater strength and durability for longer, trouble-free life.
• Setting wheels to the correct height for the cutting height quick and easy.

Low-tension belt-drive design reduces the side load on engine lower bearings and mower deck bearings for longer life.

The 48A Mower Deck features a 5/8-in. (16-mm) diameter solid-steel rod side bumper that provides extra strength and protection.

Dual-stage E-coat and powder-paint coatings provide extra protection from rust.

Versatility - easy to change between side discharge, mulch, and bagging modes

The 48A Mower is designed for maximum versatility, providing the greatest ease in changing from one mower discharge mode to another:

• With the optional MulchControl attachment installed (along with the special mulching blades), changing from side-discharge to mulching or vice versa is done with the simple flip of a lever.
• The Power Flow rear bagger can be used with the MulchControl attachment and blades installed - by simply placing the MulchControl lever in the side-discharge position.

MulchControl option

The MulchControl attachment for the 48A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The MulchControl baffle, or divider, between the left and middle spindles is about half way down. The height is designed to balance the mulching and side-discharge modes.
  • When the MulchControl baffle is open, the divider between the left and middle spindles passes a portion of the material to the discharge opening, along with the material from the middle and right spindle areas.
  • When the MulchControl baffle is closed, the material stays within the deck and gets chopped into mulch and deposited in the turf.

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
  • The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses, such as Zoysia and Bermuda
• When cutting in wet, high-growth conditions, such as those found in the Pacific Northwest United States
• When optimum bagging and lawn clean-up is desired

7-bu (247-L) Power Flow rear bagger

An optional 7-bu (247-L) rear bagger material collection system (MCS) is available. It provides an efficient means of collecting grass clippings and leaves:

• The Power Flow blower and chute are easy to install. The Power Flow blower swings out for easy cleanout and cleanup.
• The hopper design provides modern styling, great bagging performance, cleaner operation, and easy-to-empty bags:
  
  • 7-bu (247-L) capacity
  • Easy-to-attach Power Flow blower (ordered separately)
  • Easy-to-attach chute (ordered separately)
  • Air exhaust duct
  • Convenient spring-latch
  • Airflow fill indicator
  • Quik-Tatch mounting
  • Sealed hopper top
  • Loose-knit bags available

Smooth, rounded contours present a modern, styled appearance:

• Hood styling incorporates efficient full-length air-intake louvers on each side.
  • Cooler engine operation
  • Lower operator station sound levels
• Hot air is vented out the front grill, away from the operator.
• Xenoy® molded-in-color hood material is very durable.
  • Excellent impact strength
  • Hides scratches
  • Will not rust or dent
• Distinctive grille, large footrest area, and one-piece fender deck complete the styling package.

Xenoy is a trademark of SABIC Innovative Plastics.

A mower deck must be level side-to-side and properly adjusted front-to-rear to give the best cutting performance. A removable on-board deck-leveling gauge and a hex-key tool are provided to make adjustment easy. They are securely stored under the tractor seat.

Exact Adjust leveling ports are provided on each side of the operator platform above the mower-level adjusting bolts. With the hex-shaped tool, they provide convenient access to allow quick and easy adjustment of the mower for the best-cut quality of cut.

The Exact Adjust feature is standard on all Select Series™ X300 and X500 Tractors:

• There is no need to reach under the fender deck while making the mower-level adjustment.
• On-board deck-leveling gauge, Exact Adjust ports, and the hex tool work together.
  • Level the mower deck side to side
  • Set the correct amount of rake (front-to-back deck orientation)
  • Calibrate the cutting height to the cut-height adjusting knob setting
• Exact Adjust simplifies leveling the mower deck if equipped with a Power-Flow™ blower.
  • To give the best cut, mower level should be adjusted if alternately mowing with and without blower installed. The Exact Adjust feature makes this easy.

Consult the operator's manual for the correct adjusting procedures for each tractor model. Basic adjusting steps to properly level the mower deck include:

• Park the tractor on a level surface.
• Inflate tires to the correct pressure.
• Consult the label for the cutting-height knob that is located on the console of the machine. This label shows deck-leveling position and location of deck-leveling adjustment points.
• Set mower cutting-height knob to the correct deck-leveling position.
  • For X300 models, use position 2.75
  • For all other models, use position 2.5
• Adjust mower wheels as necessary so they do not contact the ground surface.
• Remove the onboard deck-leveling gauge that is located under the seat.
• Using the Exact Adjust ports and tool, adjust mower deck side-to-side level so the deck-leveling gauge just slips under the left and right lower deck rim at the designated adjustment points. The location of adjustment points will vary slightly between decks.
  • Left- and right-rear adjustment points are under the deck rim near the rear mower wheels, if equipped.
• Adjust mower deck front-to-back level, if necessary.
  • Loosen rear nuts equally on each side of front lift rod.
  • Turn front nut equally on each side clockwise to raise front of mower or counterclockwise to lower it until gauge just slips under the front adjustment point.
  • Tighten rear nuts after adjustment is complete.
• Return the gauge to its storage position. 

NOTE: The adjusting tool supplied with the tractor is an 8-mm ball-hex key, part number M162737. The rounded end allows for some misalignment with the bolt as the deck is adjusted.

The frame is made of heavy-duty formed steel, reinforced in critical areas and welded for even greater strength:

• Frame is formed from 12-gauge, 0.105-in. (2.66-mm) thick material.
• Rear hitch plate is formed from 0.25-in. (6.4-mm) steel and completes the frame assembly.
• Rear hitch plate can support up to four 42-lb (19-kg) Quik-Tatch weights.
• Optional front bumper for the X570 Tractor can support up to four 42-lb (19-kg) Quik-Tatch weights.

Features and benefits:

• Fits 17P Poly Cart (not included with MC542)
• Large 53-cu ft (1.5 m3), 42-bu (1,480-L) capacity with full 83-in. (210.8-cm) clamshell opening - perfect for fall cleanup of leaves
• Powerful 205-cc, 9.00 lb-ft* gross torque engine
• Welded steel impeller for greater suction
• Large, 8-in. (20.3-cm) diameter wire embedded hose for less clogging and larger volume pickup
• Full opening for easy access
• Vented 15-oz (425-g) poly-mesh canopy that keeps dust and exhaust away from the operator
• Contoured handles for easier open/close operation and emptying
• Custom pre-cut mower boot and welded bracket assembly for easy fit to the following John Deere Mower Decks that can be ordered separately:
  • 48, 54, and 62 in. (122, 137, and 158 cm)
  • 54- and 60-in. (137- and 152-cm) HC
  • 60-in. (152-cm) 7-Iron

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.

Specifications

 

Capacity	42 bu (1500 L), 53 cu ft (1.5 m3)
Engine	205 cc, 9.00 lb-ft* gross torque
Impeller	Welded steel
Tractor compatibility**	X500 Multi-Terrain and X700 Series Tractors
Mower compatibility	48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MC542 Material Collection System, boot and hose kits

Order number:

LP22834 - MC542 Material Collection System

LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)

LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)

LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)

LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)

LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)

LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)

LP23083 - Boot kit for 62-in. (157-cm) Mower Deck

LP39450 - MC542 Hose kit

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 3-bag Power Flow MCS. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full. 

 

One chute works with several tractor applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the tractor/mower application.

 

The 3-bag hopper installs to the tractor with the Click-N-Go™ mounting system:

• Click-N-Go brackets must be ordered separately.

NOTE: The chute can be used with 48C/48X, 54C/54X, 60-in. (152-cm) 7-Iron™, 62C/62X, 62D, 54 HC, and 60 HC Mowers.

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 2-bag Power Flow material collection system. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full.

One chute works with several vehicle applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the vehicle/mower application.

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the MC519 Cart MCS.

Deluxe thick-cushioned seat cover provides superior protection, all-day riding comfort, and lots of storage:

• Access to lumbar adjustment controls
• Large-capacity rear-zippered cargo pocket
• Two side mesh beverage pockets
• Elastic cord in bottom hem for a custom fit
• Medium size fits seats with backrests up to 15 in. (38.1 cm)

Ordering information

Contact your local John Deere dealer for availability and pricing information.

Seat cover, deluxe medium
Order number: LP92624

Seat cover protects new seats and renews old seats:

• Cushioned seat for extra comfort
• Four convenient pockets for keeping tools and gear within reach
• Elastic cord in bottom hem for a custom fit
• Medium size fits seats with backrests up to 15 in. (381 mm)

Ordering information

Contact your local John Deere dealer for availability and pricing information.

Seat cover, standard medium
Order number: LP92324

1-7/8-in. (48-mm) hitch ball attaches to drawbar or rear hitch to allow towing. 0.75-in. (19-mm) diameter post thread is provided.  

 

The hitch ball is available through Parts.

Spark arrester is available to meet the law in the State of California requiring use of a spark arresting muffler under certain conditions.

Applies in other states and Canada when needed to comply with local ordinances or customer requests.

NOTE: This law basically requires that purchasers of certain products be given written notice that it is illegal to use such machines on forest-covered, brush-covered, or grass-covered land (except watered lawns) without a spark arrester. For further information on this law, consult No. 4442.5 of the California Public Resources Code.

A thatcher mounting frame is required to install the 38-in. (97-cm) front-mounted thatcher on a vehicle.

A loose-knit bag is available as an option for use with 7-bu (247-L) cut-n-throw rear baggers and Power Flow™ baggers:

• Two loose-knit bags are required.
• The loose-knit bag allows more air to flow through and provide more complete bag filling in wet and heavy grass conditions.

 

The MC519 is compatible with Select Series™ X320, X324, X340, X360, X380, X384, X390, X394, X500 Series Multi-Terrain, X700 Series Tractors, GT200, GX300, X400, and X500 Heavy-Duty Garden Tractors, and 110 through 455 Garden Tractors.

 

NOTE: MC519 is not compatible with D100 Series, LA100 Series, L100 Series, 100 Series, or Select Series model X300, X304, X310, X330, X350, X354, X370 Tractors, LT, LX, or SST Lawn Tractors, or G100 or G110 Garden Tractors.

 

The MC519 is designed to provide the versatility of two products in one - a utility cart or a material collector.

 

Utility cart:

• 7.5 cu ft (212 L) heaped or 500 lb (227 kg) of capacity
• Ideal for hauling topsoil, gravel, sand, firewood, mulch, etc.

 

Collector:

• Large, 19-bu (23-cu ft), (670-L) capacity with a standard equipment cover
• Can be equipped with a Power Flow blower and chute for vacuuming grass clippings, thatch, pine needles, and leaves

Potential customers include homeowners, commercial operators, nurseries, and estates.

Easy to hook up and operate

The MC519 hitch can be connected to the tractor without tools in about one minute.

 

In combination with non-jackknifing caster wheels, this semi-rigid hitch makes it easy to maneuver the cart/collector.

 

An easy-to-reach handle allows dumping the cart/collector from the tractor seat.

 

For dumping extra-heavy loads, the operator can use the hand grip on the front of the box.

A standard equipment cover can be installed in a matter of seconds to convert the utility cart to a collector:

• Large plastic window in the cover allows the operator to see when the collector is full.
• Cover folds flat for space-saving wall storage.

Strong construction

The MC519 has the durability to handle homeowner or commercial applications:

• Steel support structure is mig-welded for strength.
• Cart box is made of strong, 18-gauge, 0.05-in. (1.2-mm) steel for durability.
• Puncture-resistant 4-ply rated (PR) turf tires are standard equipment.
• Greaseable bearings (wheels and casters) enable long life.
• Cover is made of tough 14-oz (397-g) black vinyl-coated nylon. The lower sides are made of 9.5-oz (269-g) black polyester knitted cloth.

Power Flow option (Power Flow blower and discharge chute must be ordered separately)

When equipped with the optional blower and discharge chute (ordered separately), the MC519 becomes a material collection system.

The blower housing material is high-density polyethylene and the fan material is ultra-high molecular weight polyethylene:

• Lightweight for easy handling and minimal effect on mowing smoothness
• Will not rust or corrode
• Resists wear and abrasion caused by sand
• Contoured design for clean appearance and smooth grass flow

Specifications

 

Capacity
Collector
Volume	19 bu (670 L) or 23 cu ft (0.67 m3)
Load	500 lb (226.8 kg)
Cart
Volume	7.5 cu ft (0.21 m3) heaped; 6 cu ft (0.17 m3) struck
Load	500 lb (226.8 kg)
Box dimensions
Width	42 in. (107 cm)
Length	30 in. (76 cm)
Depth	8 in. (20 cm)
Overall dimensions, including hitch
Width	45.5 in. (116 cm)
Length	51 in. (129.5 cm)
Depth	44 in. (112 cm)
Clearance	10 in. (25 cm)
Dump angle	50 degrees
Weight, shipping (with carton)	176 lb (80 kg)
Weight, net
Cart only	119 lb (54 kg)
Cover only	26 lb (12 kg)
Hitch only	7.7 lb (3.47 kg)
Power Flow™ dimensions
Fan diameter	13 in. (334 mm)
Fan width	2.75 in. (70 mm), 3.75 in. (95 mm) for C Series Blowers
Fan blades	4, 5 for C Series Blowers
Fan speed	3400 (will vary with mower width)
Tires	4.10x3.50 4PR
Bearings
Wheel	Iron/Oilite™ with grease fittings
Caster	Roller ball with urethane seals and grease fittings
Box material	18-gauge, 0.05-in. (1.2-mm) steel
Cover material	14-oz (0.4-kg) black vinyl-coated nylon top, front, and upper side flaps 9.5-oz (0.27-kg) black polyester knitted cloth lower sides 0.397-sq yd (0.33-m2) knitted polyester netting

 

Oilite is a trademark of Beemer Precision Incorporated.

Tractor compatibility and requirements

 The MC519 Cart is compatible with the following tractors with 48A and 54A Accel Deep™ Decks, 38, 46, 48, 48C Convertible, 48 Edge^TM Xtra Deck, 50-, 54-, 54C Convertible, 54 Edge Xtra Deck, 60, 60-in. (152-cm) 7-Iron™, 62C Convertible, 62 Edge Xtra Deck, 54-in. (137-cm) high capacity (HC), or 60-in. (152-cm) high capacity (HC) mowers:

Requirements and/or recommendations:

1. 200 lb (91 kg) (4) cast-iron rear wheel weights are recommended for ballast on GT242, GT262, GT275, GT225, GT235, GT245, 240, 245, 260, 265, 285, 320, 325, 335, 345, 355D, GX325, GX335, GX345, GX355, X500, X520, X534, and X540 Tractors when operating on slopes. Select Series X320, X324, X340, X360, X380, X384, X390, and X394 Tractors may need ballast to increase traction, stability, or steering, especially when operating on hillsides or if carrying heavier materials in the MC519 Cart. 
2. 420 and 430 Tractors require (1) AM118915 60-in. (152-cm) Power Flow installation kit for mounting 60-in. (152-cm) Power Flow blower.
3. 316, 318, 322, 330, 332, 420, 430 require black hitch mounting bracket M115521.

Required on MC519 (S/N 045001 - ) to mount on the following Tractors:

• 316, 318, 322, 330, 332, 420, and 430
• 425 Two Wheel Steer (- A040774) without 3-Point Hitch
• 425 All Wheel Steer (- B040203) without 3-Point Hitch
• 445 (- C040542) without 3-Point Hitch
• 455 Two Wheel Steer (- C040507) without 3-Point Hitch
• 455 All Wheel Steer (- D040074) without 3-Point Hitch

This bracket was included in older MC519's but was eliminated when the 425, 445 and 455 Tractors hitch design was changed and the bracket was no longer required for hookup.

4. GT, 300 and GX 48C Mowers built before April 2002 may need 0.5-in. (13-mm) hole drilled in mower wheel bracket for installing BM20667 or BM21495 48C HP Blower. See Service Information Bulletin 02-11-45-7 for detailed instructions.

5. GT, 300 and GX 48C Mowers built after April 2002 may need slot added to mower wheel bracket for installing BM19439 and BM20523 QT Blower. See Service Information Bulletin 02-11-45-7 for detailed instructions.

6. X400/X500 HDGT's and X700 Ultimate Tractors require LP52039 Adaptor Kit for MC519 Cart, available from Order Zone.

7. X400/X500 HDGT's and X700 Ultimate Tractors with a 48C/48X Mower require BM20976 or BM22798 48 HP Adapter Kit to install BM20667 48C High-Performance Power Flow Blower Assembly to accommodate this mower's rotateable wheels:

• One BM20976 48C/48X High Performance Blower Assembly Adapter Kit is required to install the BM20667 48C HP Power Flow Blower on a 48C or 48X Mower Deck (SN -050588) with wheels that rotate.
• One BM22798 48C/48X High Performance Blower Assembly Adapter Kit is required to install the BM20667 48C HP Power Flow Blower on a 48X Mower Deck (SN 050589- ) with wheels that rotate.

8. The following older 425, 445, and 455 Tractors without a 3-point hitch also require black hitch mounting bracket M115521:

• 425 two-wheel steer (A040774 and below)
• 425 all-wheel steer (B040203 and below)
• 445 (C040507 and below)
• 455 two-wheel steer (C040507 and below)
• 455 all-wheel steer (D040074 and below)

9. BM20668 54C and BM20669 62C HP Power Flow Blowers require one AM133822 Mower Wheel Adjustment Pin for installation on 2004 and later 54C or 62C Mowers.

NOTE: In order to be used as a material collection system, an optional Power Flow blower and discharge chute must be ordered in addition to the LP49228 MC519 Material Collection System.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

MC519 Material Collection System
Order number: LP49228

Features and benefits:

• Fits 17P Poly Cart (not included with MC542)
• Large 53-cu ft (1.5 m3), 42-bu (1,480-L) capacity with full 83-in. (210.8-cm) clamshell opening - perfect for fall cleanup of leaves
• Powerful 205-cc, 9.00 lb-ft* gross torque engine
• Welded steel impeller for greater suction
• Large, 8-in. (20.3-cm) diameter wire embedded hose for less clogging and larger volume pickup
• Full opening for easy access
• Vented 15-oz (425-g) poly-mesh canopy that keeps dust and exhaust away from the operator
• Contoured handles for easier open/close operation and emptying
• Custom pre-cut mower boot and welded bracket assembly for easy fit to the following John Deere Mower Decks that can be ordered separately:
  • 48, 54, and 62 in. (122, 137, and 158 cm)
  • 54- and 60-in. (137- and 152-cm) HC
  • 60-in. (152-cm) 7-Iron

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.

Specifications

 

Capacity	42 bu (1500 L), 53 cu ft (1.5 m3)
Engine	205 cc, 9.00 lb-ft* gross torque
Impeller	Welded steel
Tractor compatibility**	X500 Multi-Terrain and X700 Series Tractors
Mower compatibility	48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MC542 Material Collection System, boot and hose kits

Order number:

LP22834 - MC542 Material Collection System

LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)

LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)

LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)

LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)

LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)

LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)

LP23083 - Boot kit for 62-in. (157-cm) Mower Deck

LP39450 - MC542 Hose kit

Features and benefits:

• Fits 17P Poly Cart (not included with MC542)
• Large 53-cu ft (1.5 m3), 42-bu (1,480-L) capacity with full 83-in. (210.8-cm) clamshell opening - perfect for fall cleanup of leaves
• Powerful 205-cc, 9.00 lb-ft* gross torque engine
• Welded steel impeller for greater suction
• Large, 8-in. (20.3-cm) diameter wire embedded hose for less clogging and larger volume pickup
• Full opening for easy access
• Vented 15-oz (425-g) poly-mesh canopy that keeps dust and exhaust away from the operator
• Contoured handles for easier open/close operation and emptying
• Custom pre-cut mower boot and welded bracket assembly for easy fit to the following John Deere Mower Decks that can be ordered separately:
  • 48, 54, and 62 in. (122, 137, and 158 cm)
  • 54- and 60-in. (137- and 152-cm) HC
  • 60-in. (152-cm) 7-Iron

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.

Specifications

 

Capacity	42 bu (1500 L), 53 cu ft (1.5 m3)
Engine	205 cc, 9.00 lb-ft* gross torque
Impeller	Welded steel
Tractor compatibility**	X500 Multi-Terrain and X700 Series Tractors
Mower compatibility	48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MC542 Material Collection System, boot and hose kits

Order number:

LP22834 - MC542 Material Collection System

LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)

LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)

LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)

LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)

LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)

LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)

LP23083 - Boot kit for 62-in. (157-cm) Mower Deck

LP39450 - MC542 Hose kit

Dump from the seat capability for 3-bag material collection systems (MCS)

The MCS 14 attachment is designed to provide dump-from-seat grass collection and expulsion for all John Deere 3-bag material collection systems (MCS) on the X500 and X700 Series Tractors. The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.

The aluminum body is light weight and easy to handle. A conveniently located lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere material collection system, installation is a breeze with simple hand tools.

Features:

• Lightweight aluminum construction
• Designed for full material expulsion
• Easy access self-latching, spring-tripped handle
• Ships almost fully assembled (5 minute handle assembly)
• Installs in seconds (after initial assembly)

Benefits:

• Easy - Convenient access to dump handle directly from seat 
• Clean - No material handling, no mess 
• Efficient - Unload and go without leaving the seat

NOTE: Fits John Deere 3-bag material collection systems on X500 and X700 Series Tractors.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MCS 14 attachment
Order number: LP47170

Dump from seat capability for X500 and X700 Series 2-bag material collection systems (MCS)

The MCS 8 attachment is designed to provide dump from the seat grass collection/expulsion for all John Deere X500 and X700 Series tractors equipped with the 2-bag material collection system (MCS). The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.

The aluminum body is lightweight and easy to handle. Conveniently located hand lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere MCS, installation is a breeze with simple hand tools.

Features:

• Lightweight aluminum construction
• Designed for full material expulsion
• Easy access self-latching spring-tripped handle
• Ships almost fully assembled (5 minute handle assembly)
• Installs in seconds (after initial assembly)

Benefits:

• Easy - Convenient Access to dump handle directly from seat 
• Clean - No material handling, no mess 
• Efficient - Unload and go without leaving the seat 

NOTE: Fits All John Deere X500 and X700 Series 2-bag material collection systems. Not compatible with EZtrak™ Zero-Turn Mowers.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MCS 8 attachment
Order number: LP47169

The 14-bu (493-L), 3-bag Power Flow MCS increases the versatility of the X500 Multi-Terrain Tractors and the GT and GX Series garden tractors equipped with a 48-in. (122-cm) or 54-in. (137-cm) Convertible or Edge™ Xtra mower and C-Series high-performance Power Flow blower.

The large 14-bu (493-L) capacity means the operator can collect a large area of grass or leaves before needing to stop to empty the bags.

The 7-bu (247-L) hopper provides an efficient means of collecting grass clippings and leaves using either the cut-and-throw rear bagger or the Power Flow material collection system (MCS):

• 38-in. (97-cm) and 42-in. (107-cm) mower decks use the cut-and-throw system.
• 48-in. (122-cm) and 54-in. (137-cm) mower decks use the Power Flow system.

The hopper design provides modern styling, great bagging performance, cleaner operation, and easy-to-empty bags.

The 7-bu (247-L) MCS features:

• 7-bu (247-L) capacity
• Easy-to-attach lower chute (ordered separately)
• Handle on chute
• Air exhaust duct
• Convenient spring-latch
• Airflow fill indicator
• Quik-Tatch mounting
• Sealed hopper top
• Loose-knit bags available

The high-performance (HP) Power Flow blower assembly for the 48-in. (122-cm) Accel Deep™ Mower is used with the hopper and chute to provide a very effective material collection system. A hopper and chute must be ordered separately to complete this material collection system.

35 W sealed-beam bulb provides additional lighting for evening operation.

Light swivels and tilts to allow positioning beam on work area.

Light is designed for mounting on rear fender by drilling a hole in the desired location.

The brush guard adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

By removing one spring clip and pin, the brush guard may be lowered to permit opening the hood.

The front bumper adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

Features include:

• Bumper can be easily mounted to the front of the tractor.
• Bumper can remain on the tractor when the front blade or snow blower are used.

LG265 home maintenance kit

Home maintenance kits are a handy and convenient way for dealers to supply a customer with the maintenance-interval parts as specified in their operator's manual.

 

The LG265 home maintenance kit includes the following:

 

Quantity	Description
1	Engine oil filter
2	Engine oil quart
1	Fuel filter
1	Air filter element
1	Air filter element foam
2	Spark plug

Seat net kit provides a convenient storage area for gloves, and other small items. It is available for open-back seats.

The 21-in. (53.3-cm) professional two-piece seat, four-bar suspension, and slide shipped on Signature Series X700 Tractors is available as an upgrade seat and suspension for all X500 Multi-Terrain Tractors (model year 2006-). Key selling features for this seat include:

• Thick seat cushion for lasting comfort, even after a full day of use
• Back of seat can be angled to maximize operator comfort
  •  Convenient lever on the side of the seat unlocks back of seat to allow positioning
• Four-bar suspension and slide are included for extra comfort and bolt to the tractors fender-deck mounting holes
• BM24426 armrest attachment available as a field-installed option

Optional armrest attachment

Armrests increase operator support and comfort, thus reducing fatigue and improving productivity, especially when mowing for extended periods of time. Armrests are adjustable to suit the operator. This armrest attachment is designed for the 21-in. (53.3-cm) professional two-piece seat.

Compatibility

BM25346 21-in. (53.3-cm) professional two-piece seat, four-bar suspension, and slide is a field-installed attachment and compatible as follows:

• All Select Series™ X500 Series Multi-Terrain Tractors, model year 2006 and later

The sturdy sun shade provides an effective way to keep the sun off of the operator for more comfortable warm-weather operation of the tractor:

• Frame is made of strong 1.25-in. (32-mm) diameter steel tube with 0.063-in. (1.6-mm) wall thickness.

• The sun shade mounts to the heavy-duty CargO Mount™ system.

  • Sun shade includes the 4-wheel-steer rear weight bracket to provide a sturdy
    Quik-Tatch mounting system.
    • Holds up to two 42-lb (19-kg) Quik-Tatch weights on X300 Series Tractors
    • Holds up to four 42-lb (19-kg) Quik-Tatch weights on X500 Multi-Terrain Tractors
• Cloth top measures 32-in. (81.3-cm) long by 34-in. (86.4-cm) wide.
• Rear panel is made of cloth mesh material to provide additional protection from the sun while permitting the operator to see through it.
• Two bolts with hand knobs on the mounting posts allow easy removal of the sun shade.
• Elastic strap with clip is included to hold the 7-bu (247-L) hopper top open when the hopper is installed.
• Overall height to the top of the sun shade is 72 in. (182.9 cm).

 

The sun shade is compatible with the following:

• Select Series™ X300, X304, X320, X324, X340, X350, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

The 7-bu (247-L) 2-bag hopper or 14-bu (493-L) 3-bag hopper can be installed and used with the sun shade installed. The sun shade installation instructions explain how to install the hoppers with the sun shade.

Ordering Information

Please contact your local John Deere dealer for availability and pricing information.

 

X300/X500 Sun Shade

Order number: BM23054

This fully automatic 1.5-amp battery charger and maintainer safely charges lawn and garden, RV, deep-cycle, and most batteries that require long storage periods. It is particularly useful during winter months when the vehicle is not being used regularly, to ensure the battery stays charged:

• Automatically determines if the battery is 6- or 12-V and adjusts accordingly
• Helps maintain battery in good condition and ensures it is fully charged
• Powers on to charge battery and powers off when fully charged
• 'Onboard' feature allows mounting next to the battery on collector, street rods, and other occasional-use vehicles
• 1.5-amp trickle charges small batteries in 2 to 12 hours
• Maintains large battery charges
• Hookup protection guards battery and charger from damage 

 

Includes a choice of battery connection methods:

• Standard color-coded clips to connect to any battery
• Cable with quick-disconnect plug and end loops that can be bolted to battery terminals and easily unplugged from charger when not in use

Transporting mulch, plants or debris is easier with the double bucket holder. Just attach the holder bracket to the rear of any Select Series™ X300, X500 Series Multi-Terrain, or X700 Ultimate™ Series Tractor. It is designed to carry up to 70 lb (32 kg) of material.

 

For use with standard 5-gal. (19-L) buckets - ordered separately. 

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket holder (double)
Order number: LPJD301

Bucket (5-gal.)

Order number: LPJD400 (2 required)

This black 5-gal. (19-L) bucket perfectly complements the CargO Mount™ single and double bucket holders. It is made of sturdy black plastic.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket - 5 gal. (19-L)
Order number: LPJD400

John Deere Fuel-Protect gasoline stabilizer is a unique formula developed to ensure optimum performance and protection year-round: 

• Has corrosion preventers
• For lawn and garden equipment and other gasoline-powered vehicles
• Ensures quick starts in all two- and four-cycle engines
• Use in gasoline, gasoline-oil mixture, and ethanol blends
• Use to treat gas cans at each fill-up or use at every fill-up of vehicle
• Keeps fuel fresh for 12 months
• Contains a fuel injector and carburetor cleaner
• 1 oz treats 2 gal.

Always use fuel stabilizer in your gasoline.

Fuel sitting in gas tanks or gas containers for more than 30 days begins to degrade. Also, blended fuels and water in gasoline can form acids that corrode fuel-system components. Protect your investment - use John Deere fuel stabilizer with corrosion preventers and prevent hard starting, surging, lack of power, poor idle, flooding, and will not run or stay running conditions caused by poor-quality fuel. Ask your local John Deere dealer or visit JDParts.

Helpful tips:

• Add fuel stabilizer every time you purchase fuel.
• Deere gasoline-powered equipment is recommended to run on a minimum of 87 octane gasoline.
• John Deere Fuel-Protect for gasoline is safe to use in all types of gasoline, including gasoline/oil mixtures and blended fuels containing up to 10 percent ethanol.
• Use plastic fuel containers to store fuel; ask your local John Deere dealer.
• For best results, use a spill-proof gas can that automatically seals the gas can vent.
• Store fuel in a cool, dry, dark place in a sealed fuel can.
• Fill tank to the top every time the machine is put away.
  • Make sure tank is drained if stored for the winter or treated if left for prolonged periods of time.

Please refer to the operator’s manual for additional recommendations and warranty information.

Fuel related issues are not considered a warrantable condition as there is no defect in the materials or workmanship of the machine. 

For more information on fuel, visit John Deere Groundscare.

Features and benefits

• Homeowners can now achieve results just like the professionals
• Brush is easy to adjust for varying mower cutting height
• Brush adjusts to varying ground conditions and allows the operator to freely maneuver the vehicle without damaging the turf
• The brush striping kit is a very economical and functional attachment

Compatible with the following:

• 48A or 54A - 48-in. (122-cm) or 54-in. (137-cm) Side-Discharge Mower for X350, X354, X370, X380, X384, X390, X394, X570, X580, X584, and X590 (model year 2016) Tractors

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

48A or 54A - 48-in. (122-cm) and 54-in. (137-cm) grass groomer

Order number: LP63761

Leveling gauge allows quick and accurate mower deck leveling and cutting height adjustment.

Can be used for:

• Lawn tractors
• Lawn and garden tractors
• Riding mowers
• Front mowers
• Commercial walk-behind mowers
• Zero-turn-radius mowers

MulchControl advantages and benefits

The MulchControl attachment for the 48A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The MulchControl baffle, or divider, between the left and middle spindles is about half way down. The height is designed to balance the mulching and side-discharge modes.
  • When the MulchControl baffle is open, the divider between the left and middle spindles passes a portion of the material to the discharge opening, along with the material from the middle and right spindle areas.
  • When the MulchControl baffle is closed, this material stays within the deck and gets chopped into mulch and deposited in the turf.

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
  • The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

MulchControl limitations

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses, such as Zoysia and Bermuda
• When cutting in wet, high-growth conditions, such as those found in the Pacific Northwest United States
• When optimum bagging and lawn clean-up is desired

Features and benefits:

• 100-psi (689-kPa) SHURflo® diaphragm-type pump is designed for high-hour commercial applications; it can be run dry without damage.
• It is easy to assemble the custom mounting brackets.
  • Brackets use the existing frame holes.
• Brass-tipped spray wand is included as standard equipment; it is constructed of noncorrosive polypropylene material with Viton® components for multi-use applications.
• Check valves in the boom tips prevent siphoning and dripping, which can cause lawn spotting.
• Control valve directs spray to either the boom or spray wand for added convenience
  and versatility.
• Electrical hookup is simple with a convenient on/off switch.
• Sprayer contains a rugged translucent-yellow tank with molded fill-level indicators (in gallons).
• It is only a 15-second no-tools mounting after assembly.

Specifications

Item number	LP22861
Tank capacity	25 gal. (95 L)
Boom	60-in. (152.4-cm) boom, 90-in. (228.6-cm) spray
Spray wand reach	30 ft (9.1 m)
Hose length	19 ft (8 m)
Shipping weight	35 lb (16 kg)
Warranty	2-year consumer warranty

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

25-gal. (95-L) Mounted Sprayer for X300 and X500 Tractors

Order number: LP22861

SHURflo is a trademark of SHURflo, LLC.

Viton is a trademark DuPont Performance Elastomers.

The 40-in. (102-cm) Tractor Shovel expands the usefulness of any John Deere Select Series^TM X300 or X500 Multi-Terrain Tractor by allowing it to pick up and move material. It utilizes a high-capacity electric actuator that provides lift, lower, dump, and down force functions. No front blade is required.

The tractor shovel takes the back-breaking labor out of jobs like moving mulch, spreading gravel, ground grading, and more. It installs using the tractor's existing frame holes. After initial installation, it can be removed or installed without tools.

The innovative opening design of the tractor shovel, combined with the lift height, assures complete emptying of material. The tractor shovel can also be used for scraping and grading by locking the shovel in the raised position.

Tractor recommendations and requirements:

• Rear tractor ballast recommended for improved traction
• Tire chains recommended for moving snow
• No tractor requirements

 Key features:

• Can be used when upper part of shovel is locked in the raised position as a blade (without angling capability)
• Raised and lowered with electric actuator
• Provides down force to increase scraping effectiveness of blade
• Pick-up, transport, and empty a variety of loose material including soil, gravel, mulch, and snow
• Can be removed in 10 minutes or less

Compatibility:

• LP63767 40-in. (102-cm) Tractor Shovel is Compatible with:
• Select Series X300, X300R, X304, X310, X320, X324, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

 

Unique shovel design

The unique design of the 40-in. (102-cm) Tractor Shovel allows an operator who has a Select Series™ X300 Series (including X300R and X350R) or X500 Series Multi-Terrain Tractor to use the tractor shovel for lifting and moving material as well as for typical blade functions (without blade angling), such as blading, leveling, and scraping:

• Unique shovel design empties material completely.
• Shovel can be locked in the raised position for blading applications.

Operation

The tractor shovel is operated from the tractor seat with the use of a control rod and an electric switch.

An electric actuator provides power to raise, lower, and empty the shovel.

To raise or lower the tractor shovel, use the electric switch on the tractor shovel panel.

Depress the bottom of the switch to raise the shovel and depress the top of the switch to lower the shovel.

To open the shovel for emptying, raise it completely and then pull the control rod to the yellow area of the rod and press the upper end of the electric switch.

To close the shovel, press the lower end of the electric switch until the control rod releases to the black area of the rod.

Operation of the shovel for blading or leveling

To use the tractor shovel for blading, use the handle on the right side of the shovel to raise it and then use the locking lever to lock it in the raised position.

 Specifications

 

Length of tractor shovel	40 in. (101.6 cm)
Depth of tractor shovel	11 in. (27.9 cm)
Capacity	1.7 ft3 (48 L)
Cutting blade material	0.250-in. (6.4-mm) hardened steel
Material thickness, shovel	0.125 in. (3.2 mm)
Load capacity	150 lb (68 kg), evenly distributed
Lift height	4 in. to 6 in. (10.2 cm to 15.2 cm), depending on the tractor model
Shipping weight	110 lb (50 kg)
Warranty	One-year limited warranty on parts

Tractor compatibility and requirements

The 40-in. (102-cm) Tractor Shovel is compatible with the following tractors:

• Select Series X300, X300R, X304, X310, X320, X324, X330, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

Requirements and/or recommendations:

1. Rear ballast is recommended for best performance.
2. Tire chains are helpful and recommended when operating in snow.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tractor Shovel
Order number: LP63767

The electric power lift kit makes winter work easier by taking the effort out of raising and lowering front blade and snow blower attachments:

• Designed for Select Series™ model X350, X354, X380, X384, and X570 Tractors with foot lift
• For use with X300 and X500 front blade and snow blower attachments

Key features include:

• Includes convenient dash-mounted control switch and all electrical components
• Heavy-duty powder-coated steel components
• Controlled down force for increased usability of front blades and snow blowers
  • Provides ability to have down pressure and set implement height during work
• 4-in. (10-cm) to 6-in. (15-cm) lift height (depending on tractor model) and controllable, limited down force
• Helpful when maneuvering near curbs and for trailer loading
• Heavy-duty electric actuator designed for high-hour usage for effortless lift and lower
• Installation with simple hand tools

NOTE: The electric power lift is separate from the tractor's lift system and cannot be used to raise the mower deck. The front implement hitch uses the same tractor frame holes as the mower front draft arms; therefore, the mower deck and the snow blower or front blade cannot be mounted on the tractor at the same time.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Electric Lift Kit, X300/X500

Order number: LP64865

The integral hitch permits the use of certain rear-mounted equipment, such as a cultivator, disk harrow, plow, or box scraper/blade attachment.

Key features include:

• Lifts/lowers using included mechanical hand-operated lever
  • Provides reasonable lift efforts
• Uses one pin and spring clip for installation or removal
• May be installed at the same time as the mower, front blade, or snow thrower
• Can install 42-lb (19-kg) Quik-Tatch™ suitcase weights for ballast when using the integral hitch
• Compatible with GT and GX garden tractors and X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Integral hitch

Order number: LP31357

Features include:

• Dual vents let air circulate and help prevent ballooning in wind
• Elastic shock cord in bottom hem for a quick, custom-like fit
• Coated fabric for maximum water protection
• One-year warranty

Cover provides all-season protection for 100 Series, S240 Sport and Select Series™ X300 Series Tractors.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

Protective cover (standard)

Order number: LP93917

The roomy steel-frame cab shields the operator against snow, rain, sun, and wind.
Key features include:

• Easy entry with hinged-door access
• Double-zippered access hole for control maneuverability
• Super-clear vinyl windows that are cold-crack tested to -4°F (-20°C)
• Zippered windows that allow for additional airflow
• Assembles and installs with standard hand tools in one hour
• Overall height from ground to top of cab of 78 in. (198 cm)

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

Weather enclosure

• Discontinued - LP36740 Weather Enclosure - Select Series™ X300, X304, X310, X320, X324, X340, and X360 Tractors
• LP55438 Weather Enclosure - Select Series™ X300, X304, X310, X320, X324, X340, X350, X360, X354, X370, X380, X384, X390, and X394 Tractors
• Discontinued - LP36741 Weather Enclosure - Select Series X500, X520, X530, X534, X540, and X590 (model year 2015) Multi-Terrain Tractors
• LP55439 Weather Enclosure - Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

Cover provides heavy-duty protection for Select Series™ X300, X500, and X700 Tractors.

Features include:

• Wipe-clean reinforced bottom around mower deck
• Easy-on side handles makes snugging down cover a snap
• Dual reinforced air vents let air circulate and help prevent ballooning in wind
• Interior lining and integrated muffler heat shield
• Heavy-duty fabric will not shrink or stretch and is coated for maximum water resistance
• Easy-on split back for fast fitting and easy access after installation
• Handy storage pocket reverses into an attractive storage case
• Two-year warranty

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

Protective cover (large deluxe)

Order number: LP93647

NOTE: The photo above shows the earlier AM136691 winter grille cover on a pre-2014 X300 Tractor. AM145350 winter grille cover replaces AM136691. It is similar in appearance and designed for use with the earlier hoods as well as the 2014 and later hoods used on X300 Series Tractors (SN 280,001-) with the newer styling.

 

Winter grille covers are available as an accessory for Select Series™ X300 and air-cooled X500 Multi-
Terrain Tractors:

• Faster engine warm-up and higher winter operating temperature
• Prevents the engine carburetor from icing-up while blowing or blading snow, or
  during similar applications, when operating in certain cold weather conditions
• Elastic straps make installation and removal quick and easy

*The winter grille cover is recommended only for air-cooled tractors; use of the winter grille cover on a
liquid-cooled tractor may cause the engine to overheat, which will cause the power take-off (PTO) to disengage.

NOTE: To avoid engine damage, the winter grille cover must be removed when outside temperature reaches 40 degrees F (4 degrees C) or higher.

The purpose of the winter grille cover is to seal the side vents on the hood; they need to be blocked completely. The cover must be aligned properly to accomplish this. If the sides are not sealed, carburetor icing may still be a problem.

Symptoms of carburetor icing:

• While blowing snow in freezing temperatures, the engine gradually loses power, emits black smoke from exhaust, misses, stalls, and fouls spark plugs.
• If the tractor is left outside in freezing temperatures after blowing snow, the choke may not move when trying to start the engine.
• Engine will start after sitting outside in freezing temperatures, but runs poorly and lacks power; black smoke may be emitted through the exhaust.

The mounted electric broadcast spreader for Select Series and Signature Series Tractors is ideal for medium- to large-size jobs and can be used to apply fertilizer, weed killer, sand, lime, and de-icer:

• Compatible with X300 and X500 Select Series and X700 Signature Series Tractors
  • X300 Series Tractors must be equipped with 35-lb (16-kg) front wheel weights or front weight bracket and two 42-lb (19.1-kg) Quik-Tatch weights.
  • The electric broadcast spreader is not compatible with the X300R Rear Discharge Tractor.
  • When used on X700 Series Tractors, the spreader is not compatible with the weather enclosure, cabs, rear receiver hitch, or 3-point hitch.

Key features are as follows:

• 125-lb (57-kg) capacity injection molded poly hopper
• Durable welded, powder-coat frame
• Ice-melt capability
• Gear motor with 5-to-1 reducer
• Stainless-steel shutoff plates
• Directional control
• Hopper cover is standard equipment
• Available option: Barrier shield, 125-lb (57-kg) spreader

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Select Series Electric Spreader

Item number: LP35439

The thatcher, used on a regular basis, reduces excessive thatch buildup that can be damaging to a lawn's health.
 
Since it provides more gentle, less aggressive action than a power rake, it can be used as a preventive maintenance tool each time the lawn is mowed.

Ordering information

 

Please contact a local John Deere dealer for availability and pricing information.

38-in. (97-cm) Front Thatcher

Order number: LP48004

An 8-in. (20-cm) extension is available to provide widths of 46 in. (117 cm) and 54 in. (137 cm) (Add an extension to one end of front thatcher to make it 46-in. [117-cm] wide; add an extension to both ends for a 56-in. [142-cm] width.)

Chains are recommended for extra traction when using attachments such as a snow blower or front blade.

One pair of chains is included in each bundle.

TY15959 tire chains - 20x8-8
NOTE: For LA105, LA115, LA125, D100, D105, D110, D120, and D125 Tractors.

TY16200 tire chains - 20x10-8, 20x10-10
NOTE: For LA135 SE, LA145, LA155, D130, D140, D150, D155, S240, X300/less deck, X300/38X, X300/42M, X300/42X, X300/48X, X300R, X304, and X324 Tractors.
NOTE: 20x10-8 tires and 20x10-10 tires use the same chains as the height and width are the same. The rim diameter is larger for four-wheel steer tires, but does not affect chain requirements.

TY25229 tire chains - 22x9.5-12
NOTE: For LA165, LA175, D160, and D170 Tractors.

TY24327 tire chains - 22x11-10
NOTE: For X320, X340, and X360 Tractors.

TY15956 tire chains - 23x10.5-12
NOTE: For 190C Tractor.

TY26227 tire chains - 23x9.5-12, 24x9.5-12
NOTE: For X534 Tractor.

TY24328 tire chains - 24x12-12
NOTE: For X500, X520, X530, X540, and X590 Tractors.

TY25326 tire chains - 26x10.5-12
NOTE: For X724, X734, X744, and X754 Tractors. They fit turf, bar, and heavy-duty all-purpose (HDAP) tire treads.

TY15958 tire chains - 26x12-12
NOTE: For X700, X710, X720, X730, X728, X738, X729, X739, X740, X750, X748, X758, and X749 Tractors. Will fit turf, bar, and HDAP tire treads. X729, X739, and X749 require BM22725 wheel spacer kit to provide clearance when installing tire chains.

One 30-lb (13.6-kg) cast-iron weight may be installed on each front wheel for additional stability when operating on hillsides or with heavy rear equipment.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front wheel weights are not available for special-edition tractors because the styled front  wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.

One or two 50-lb (22.7-kg) cast-iron weights may be installed on each rear wheel to provide extra traction and stability.

Features include:

• Weights are made of durable cast iron and painted John Deere yellow.
• Weights may be installed with the wheel in either the narrow or wide position.
• These weights may be used on both two-wheel-steer and all-wheel-steer tractors.
• To stack the weights and install two on a wheel, two 1/2x8-in. (12.7x203-mm) bolts are required per wheel (not furnished).
• X700 Special Edition Tractors (model year 2012 and prior) and X738, X739, and X758 Signature Series Tractors require a BM21497 wheel weight adapter ring on each rear wheel on which weights are to be installled.

One 50-lb (22.7-kg) plastic-shell rear wheel weight may be installed on each rear wheel to provide extra traction and stability.

The outer shell is molded of tough polyethylene plastic and filled with a heavy, granular material that contains a high percentage of iron. A bonding substance is added to hold the material together so that it will remain intact, even if the shell is damaged.

Multiple stacking is not recommended.

Overall width of the tractor will be increased by approximately 2 in. (51 mm) when weights are installed.

Compatibility:

• 23x10.5-12 and 24x12-12 wheels and tires in narrow position only
• 26x12-12 wheels and tires

Weights are packaged one per carton, with necessary hardware for installation on a wheel.

X700 Special Edition Tractors (model year 2012 and prior) and X738, X739, and X758 Signature Series Tractors require a BM21497 wheel weight adapter ring on each rear wheel on which weights are to be installed.

NOTES:

1. Plastic rear wheel weight comes with necessary hardware for installation.
2. X Series Special-Edition Tractors require an additional BM21497 special-edition weight adapter for each rear wheel on which weights are to be installed.

For 50-lb (22.7-kg) cast-iron wheel weights on 23x10.50-12 or 24x12-12 rear tires:

 

BM17985 - for mounting one 50-lb (22.7-kg) weight

BM17977 - for mounting two 50-lb (22.7-kg) weights

For 50-lb (22.7-kg) cast-iron wheel weights on 26x12-in. rear tires:

 

BM17977 - for mounting one 50-lb (22.7-kg) weight

BM18101 - for mounting two 50-lb (22.7-kg) weights 

For 72-lb (32.7-kg) starter cast-iron wheel weight on 26x12-12-in. rear tires:

 

BM18089 - for mounting 72-lb (32.7-kg) starter weight

For 72-lb (32.7-kg) starter and 50-lb (22.7-kg) cast-iron weight(s):

 

BM17977 - for mounting one 72-lb (32.7-kg) starter and one 50-lb (22.7-kg) weight

BM18101 - for mounting one 72-lb (32.7-kg) starter and two 50-lb (22.7-kg) weights

A - one (1) BM17973 and one (1) BM17972 weight
B - one (1) BM17973 and two (2) BM17972 weights

Four-wheel-steer tractors

NOTE: Plastic wheel weight is not compatible with four-wheel-steer tractors.

For 50-lb (22.7-kg) cast-iron wheel weight on 26x10.50-12 tires:

 

BM18094 - for mounting one 50-lb (22.7-kg) weight

BM17977 - for mounting two 50-lb (22.7-kg) weights

The 42-lb (19.1-kg) Quik-Tatch can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.

This weight is constructed of cast iron and weighs approximately 42 lb (19.1 kg).

Some vehicles have built-in front and/or rear weight brackets to hang the weights on; others require a weight bracket that must be ordered separately.

X400/X500 Heavy-Duty Garden Tractors and X700 Series Tractors require the following parts when weights are installed on the front of the tractor:

• One  M147986 weight retaining rod (Parts)
• Two  M40461 spring clip (Parts)

Hardware is required for installing each front-wheel weight.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front-wheel weights are not available for special edition tractors because the styled front-wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.

The optional front weight bracket/bumper is available to replace the standard front bumper on the following tractors:

• Select Series™ X300, X300R, X304, X305R, X310, X320, X324, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Model year 2007 and later (SN 020001-) Select Series model X500 Tractor
• All X530 Select Series Tractors
• Model year 2011 and later (SN 060001-) Select Series model X534 Tractor
• X570 Select Series Tractor

NOTE: Weights are ordered separately.

Holds up to four 42-lb (19.1-kg) Quik-Tatch weights:

• Provides an alternative to front-wheel weights for ballasting rear-mounted equipment
• Makes the 42-in. (106.7-cm) Hydraulic Tiller compatible with the X530 Tractor
• Functions as a bumper when weights are not installed

 

Can be used in combination with all John Deere equipment, except the following:

• Styled front bumper (BM23056)
• 40-in. (101.6-cm) Tractor Shovel

Turf tire features:

• 12-in. (305 mm) wide
• Provide reduced tire pressure on lawn
• Ideal for mowing work
• Round shoulder design minimizes scuffing on turns

 

Bar-type tire features:

• 10-1/2-in. (267 mm) wide
• Provide more traction than turf tires
• Ideal for front blade or similar type work

 

Heavy-duty all-purpose (HDAP) tire features:

• 12-in. (305 mm) wide
• Provide more traction than turf tires
• Easier on turf than bar tires

Turf tire features:

• 12-in. (305 mm) wide
• Provide reduced tire pressure on lawn
• Ideal for mowing work
• Round shoulder design minimizes scuffing on turns

 

Bar-type tire features:

• 10-1/2-in. (267 mm) wide
• Provide more traction than turf tires
• Ideal for front blade or similar type work

 

Heavy-duty all-purpose (HDAP) tire features:

• 12-in. (305 mm) wide
• Provide more traction than turf tires
• Easier on turf than bar tires

Turf tire features:

• 12-in. (305 mm) wide
• Provide reduced tire pressure on lawn
• Ideal for mowing work
• Round shoulder design minimizes scuffing on turns

 

Bar-type tire features:

• 10-1/2-in. (267 mm) wide
• Provide more traction than turf tires
• Ideal for front blade or similar type work

 

Heavy-duty all-purpose (HDAP) tire features:

• 12-in. (305 mm) wide
• Provide more traction than turf tires
• Easier on turf than bar tires