Compact Tractors | Model Year 2023 2038R

Powerful, high-torque diesel engine delivers superb efficiency

Yanmar 3-cylinder, TNV series diesel engine

2032R

The 1.642-L (100.2-cu in.) displacement, liquid-cooled 3TNV88C-NJT Yanmar® diesel engine provides 22.9 kW ( 30.7 hp) to the 2032R.

Model	Number of cylinders	Engine displacement	Aspiration	Gross engine power*	Gross engine PS*	Power take-off (PTO) power*
2032R	3	1.642 L (110.2 cu in.)	Natural	22.9 kW (30.7 hp)	31.2 PS	18 kW (24.2 hp)

*Engine kW (hp), gross SAE J1995: 22.9 (30.7) at 2500 rpm, PS

Displacement, L (cu in).: 1.642 (100.2)

2038R

The 1.568-L (95.8-cu in.) displacement, turbocharged liquid-cooled 3TNV86T-NJT Yanmar diesel engine provides 27.4 kW ( 36.7 hp) to the 2038R.

Model	Number of cylinders	Engine displacement	Aspiration	Gross engine power*	Gross engine PS*	PTO power*
2038R	3	1.568 L (95.8 cu in.)	Turbocharged	27.4 kW (36.7 hp)	37.2 PS	22.7 kW (30.4 hp)

*Engine kW (hp), gross SAE J1995: 27.4 (36.7) at 2500 rpm, PS

Displacement, L (cu in.): 1.568 (95.8)

The engine uses the latest technologies to optimize fuel economy, improve control and accuracy, and reduce environmental impact.

The common rail system (CRS) optimizes fuel economy and reduces operating costs. High-pressure injection atomizes fuel into finer particles which burn more completely. It results in improved fuel economy and a lower cost of operation.

The electronic control unit (ECU) provides optimum fuel control and accuracy. ECU monitors and controls the engine. It continuously monitors engine conditions and adjusts the fuel delivery accordingly to ensure optimum performance and emissions.

The engine comes with an aftertreatment system. The system operates automatically. The exhaust filter consists of a diesel particulate filter (DPF) which captures particulate matter (PM) contained in the exhaust gas. Using a natural cleaning process, most of the PM trapped in the exhaust filter is eliminated by the heat of the exhaust stream generated by normal use. In situations of low temperature, engine speed or load factor, an active cleaning cycle is initiated. In this cleaning cycle, the exhaust gas temperature is raised by injecting additional fuel during the exhaust stroke of normal vehicle operation to the diesel oxidation catalyst (DOC).

After many hours of use, the exhaust filter may require an ash removal service.

DOC/DPF

Depending on the load that the tractor is under, as well as ambient temperature, humidity, and engine speed, the DPF may build up with particulate matter, thus requiring cleaning. Filter cleaning is determined by one of three conditions:

A prescribed time-based estimation of needed filter cleaning
DOC/DPF pressure sensors
A particulate matter buildup estimation based on load conditions

Once one of the three conditions have been met, filter cleaning will occur. There are three different types of filter cleaning processes:

Passive filter cleaning
Active filter cleaning
Parked filter cleaning

Passive filter cleaning

Passive filter cleaning occurs naturally when the engine is generating enough heat to oxidize particulate matter. This automatic process occurs continuously during normal operating conditions. No tractor icons or symbols appear on the display during passive filter cleaning.

NOTE: Passive filter cleaning requires no operator involvement, and there is no interruption to tractor operation.

Active filter cleaning

If conditions (temperature, load, or speed) for passive filter cleaning cannot be achieved, then particulate matter is removed using active filter cleaner.

To achieve the required conditions, exhaust temperature management (ETM) manages the initiation and duration of active filter cleaning. ETM can adjust numerous engine parameters and/or inject a small quantity of fuel into the exhaust stream for a short duration. The fuel turns to vapor and chemically reacts with the catalysts in the DOC to create heat to oxidize particulate matter.

It is important to note that at no time is fuel in the DOC/DPF ignited, and there is no interruption to tractor operation.

Like passive filter cleaning, active filter cleaning requires no operator involvement, and there is no interruption to tractor operation.

Parked filter cleaning

In some instances where passive and active filter cleaning have not fully cleaned the particulate matter from the system, a parked filter cleaning may need to take place. Most likely, the only time a parked filter cleaning will need to occur is when automatic filter cleaning has been disabled for an extended period of time and multiple warnings to engage filter cleaning were ignored or if the tractor has been used during light load conditions. Additionally, when the automatic filter cleaning process has been deliberately interrupted multiple times, or if active filter cleaning has failed numerous times due to a failed component, a parked filter cleaning may be requested. In these rare instances the operator will have to park the tractor and start the filter cleaning process.

The parked filter cleaning process needs to be activated based on usage and operation of the tractor. The process will take approximately 30 minutes. See operator’s manual for more details.

The emissions system on this engine constantly monitors the soot level of the tractor, making sure the tractor is always in peak performance condition. This ensures high performance at all times.

NOTE: Number of hours since last regeneration and soot level percentage viewable on LCD display.

For more information regarding Environmental Protection Agency (EPA) regulations and the technology behind John Deere Integrated Emissions Control systems, click here.

Yanmar TNV Series engine offers these features:

Economical cast-in-block cylinder design for good cooling and long life
Direct fuel injection
- Improves starting
- Injects fuel directly on top of pistons for more efficient combustion
- Develops more horsepower per gallon of fuel than indirect injection engines
Aluminum alloy pistons are lightweight to reduce connecting rod bearing loads and provide good heat transfer characteristics
- Design permits tighter tolerances and neutralizes expansion of the piston, which reduces blow-by and noise from piston slap
- Top rings are higher on the piston and a thinner head gasket is used to greatly reduce the volume of unburned waste gases and increase combustion efficiency
Timing gears and injector drive gears have a helical profile to reduce engine noise
Auto-bleed fuel system
- There is no need to prime the system if the tractor runs out of fuel
- The system self-primes the injection pump, lines and injectors, providing fast fuel recovery for easier starting
High-capacity lubrication system provides filtered oil, under pressure, to all engine bearings for long life
Fuel filter with replaceable element
Water separator with additional replaceable filter element
See-through coolant recovery tank permits operator to check coolant level without removing radiator cap
Dry-type air cleaner with safety element

Dual element design for added engine protection
Air cleaner service indicator is standard equipment on all models and alerts the operator on the instrument panels

Easy access to engine check and fill points on the right-hand side of the tractor by removing the side panels

Yanmar is a trademark of Yanmar Co., Ltd.

Easy-to-use hydrostatic transmission (HST) increases productivity

The 2032R and 2038R Tractors are equipped with a two-range hydrostatic transmission (HST) incorporated in a die-cast aluminum transmission case. Fluid under pressure transmits engine power to the drive wheels via a closed-loop pump and motor arrangement. Infinite ground speeds allow the operator to match the speed of the tractor to the job.

No clutching for fast and easy direction changes
Twin Touch™ foot pedals for quick and easy forward/reverse operation
Transmission oil cooler cools transmission oil for longer transmission life

Safety features of the HST transmission include:

The tractor will only start with the range lever in neutral

If the range lever is in gear when the key is turned to the start position, the instrument panel instructs the operator to shift to neutral

The engine will shut off if the operator leaves the seat and the power take-off (PTO) is engaged

Twin Touch foot controls

Key John Deere advantages – John Deere’s Twin Touch foot controls offer several key advantages over competitive HST models tractors.

Some competitive hydrostatic tractors use a treadle pedal (toe-heel) design foot control for operation of the HST

Requires the operator to use both toe and heel to change direction, resulting in increased operator fatigue
The Twin Touch configuration also makes it easier to inch the tractor forward or rearward (i.e., when attaching to implements)

Integrated hydrostatic pump and motor

Sauer-Danfoss® manufacturer provides the integrated pump and motor; this assures that the components are matched to each other, providing maximum efficiency
Provides strength and durability needed for operating such attachments as loaders and backhoes
One reservoir (with one check-point and fill point) for the transmission, differential, and hydraulic system speeds up daily maintenance
Mechanically actuated by Twin Touch foot pedals allow the operator to select both directions of travel and speed with the touch of a toe

Cruise control

An electronic cruise control is standard equipment on the 2032R and 2038R Tractors. Cruise control is electronically engaged and disengaged using a toggle switch located on the right-hand console.

Maintains desired forward speed without having to touch the forward pedal
To disengage the cruise control, either apply pressure to the brake pedal or disengage the cruise control switch

Sauer-Danfoss is a trademark of Sauer-Danfoss Incorporated.

Operator station is comfortable and convenient

Operator Station

The operator station has been designed to allow for greater operator comfort and increased visibility. The ergonomic layout and convenient color coded controls allow for easy identification and operation. The design of the operator station allows operators to sit “in” as opposed to “on” which provides comfort and increased stability.

Below are other key features of the 2032R and 2038R Tractor operator’s station:

Sloping hood design provides improved visibility
Plenty of room for comfortable operation
Cup holder, multiple storage compartments and a 12V outlet ensures an organized operator station
Rubberized floor mat design to reduce vibration and noise
Step-through operator platform makes getting on and off the tractor easy
Fender-mounted handrails, large and easy to grab, assist the operator when getting on and off the tractor
Controls have been raised and integrated into the fender for operator comfort and ease of use
Large, easy to read decals provide clear instructions for experienced and even non experienced operators
Front horizontal exhaust for increased operator visibility
If the operator leaves the tractor seat when the transmission, mid PTO, or rear PTO is engaged, the engine will shut down

For applications where out-of-seat PTO operation is required, the following criteria must be met: transmission in neutral, park brake engaged, and PTO selector set to rear only. See operator's manual for specific instructions.

Specially designed panels route hot air flow from the engine compartment under the tractor instead of directly onto the operator

Left-side step

Left-side entrance step

The left-side step allows for easy access on and off the tractor
Foot platform has a non-skid surface

Premium seat

Premium high-back seat

The thick, soft padding on this seat provides a smooth and comfortable ride with added weather resistance from marine grade vinyl that is easy to clean. A high, scalloped back makes it easier for the operator to turn to view rear implements.

Seat adjusts fore/aft for operator convenience
Seat flips forward for protection from the elements
High seat back and armrests are in base equipment and allow for a more comfortable operation
Retractable seat belt feature prevents the seat belt from becoming tangled in the seat suspension and controls

Key features of the operator’s station include:

Tilt steering wheel design in base equipment on the 2032R and 2038R Tractors

Allows the operator to adjust the steering wheel to the most comfortable position
Provides additional clearance for the operator to enter and exit the tractor
Provides easy return to the fully raised position
Provides plenty of room for comfortable operation

Tilt steering lever

Easy-fold ROPS allows tractor to be used or stored in low clearance environments

Optional iMatch™ Quick-Hitch feature allows for easy implement hookup

iMatch Quick-Hitch (LVB25976)

One of the greatest operator concerns involves difficulty in attaching tractor implements. John Deere has addressed this issue with the iMatch Quick-Hitch.

The iMatch Quick-Hitch provides easy hookup and a guaranteed fit for all Category 1 implements that are designed to meet the American Society of Agricultural and Biological Engineers (ASABE) Category 1 Standard S278.6 for quick-attach hitches.

All implements require a set of bushings in order for the attachment to fit and work properly with the iMatch Quick-Hitch. One set of bushings comes with the iMatch Quick-Hitch.

NOTE: The bushing set can be seen in the picture above. These bushings allow the hooks on the iMatch and the pins on the implement to fit together properly. All other implements (box blades, tillers, rear blades, etc.) will require a set of bushings to enlarge the pin to fit with the iMatch hooks. Bushings of different lengths can be found in the parts system or through a bushing supplier (see dimensions below).

Upper bushing
- Inside diameter: 1.93-1.95 cm (0.76-0.77 in.)
- Outside diameter: 3.15-3.18 cm (1.24-1.25 in.)
Lower bushings
- Inside diameter: 2.24-2.26 cm (0.88 to 0.89 in.)
- Outside diameter: 3.63-3.66 cm (1.43 to 1.44 in.)

CommandCut™ controls allows quick and accurate height of cut adjustments

Instrument panel

CommandCut™ controls

The 2032R and 2038R tractors features the CommandCut™ mower deck lift system, which allows quick and accurate adjustments of the mower deck with the turn of a dial and the bump of a lever. Control callouts make operation simple and repeatable. The height of cut setting dial and raise/lower lever are conveniently located on the right-hand console and easily accessible by the operator. Some of the key benefits of this system are:

Installing CommandCut™ only requires a simple calibration after installation. It is a true “plug-and-play” system as no controller programming is required.
Inhibits PTO operation when mower deck is in the install position to prevent PTO driveling and mower deck blade damage
Eliminates the need for hydraulic power and components, thus dedicating all hydraulic capacity to other implements or tract functions

Fewer hydraulic components means fewer hydraulic leaks, especially when working on sensitive turf

Precise height of cut with no drift or leakdown

System can be calibrated to different tire sizes to maintain precision

Minimum effort required to set height of cut and to raise/lower the mower deck which reduces operator fatigue
Easy to read graphical interface on the instrument panel allows operator to glance at the desired height of cut while staying focused on mowing
Built in transport lock can be activated from the seat by turning the height of cut dial to position 6 and raising the deck to the highest position

Excellent serviceability and diagnostics reduce operational cost and improves productivity

Regular service and maintenance are essential to the performance, productivity, and longevity of the tractor.

Tractors are equipped with extensive onboard self-diagnostic capabilities and are fully compatible with the John Deere-exclusive ServiceADVISOR™ system.

Four quarter turn fasteners allow operators to easily remove the engine side panels without tools to access to the engine compartment.

Quarter turn fasteners

Right tractor side panel removed

Easy access to regular service points minimizes service time
Daily service checks, such as checking the engine oil or water separator, can be done without opening the hood or removing the tractor side panels
Tractors are equipped with an electronic air filter restriction indicator that alerts the operator when the air filter needs to be cleaned or changed

Air filter restriction sensor

Daily service requirements are minimal and simple to accomplish. Most service interval requirements can be performed with a basic understanding of procedures and common tools.
All external engine, fuel and transmission filters are easily accessible
Increased service intervals lessen overall cost of ownership
Hydraulic oil service interval increased to 1200 hours when using Hy-Gard™ products
Hydraulic oil filter will need to be changed every 400 hours
Fuel tank is located on the rear of the tractor to allow for easy access when fueling

Fuel Tank

Gas-lift hood support eliminates the need for a mechanical prop rod

Gas-lift hood shocks

All items in the daily service schedule can be performed without the use of tools:

Engine oil, hydraulic oil, coolant level, and the water separator can be conveniently accessed
The engine can be easily accessed by simply raising the hood for more periodic maintenance checks

NOTE: Always refer to the operator’s manual for complete maintenance and service recommendations.

Engine power (gross)	SAE J1995 rated power: 27.4 kW 36.7 hp 37.2 PS at 2500 rpm
Power take-off (PTO) power	22.7 kW 30.4 hp
Steering hydraulics	15 L/min 4 gpm
Implement hydraulics	20.2 L/min 5.3 gpm
Hitch type	Category 1
Lift capacity, 24-in. behind link arms	615 kg 1356 lb
Standard transmission; forward/reverse	Hydrostatic transmission (HST)
Cruise control	Standard
Approximate shipping weight (open-station; cab)	Open station: 1320 kg 2910 lb Cab: Not applicable
Wheelbase	1723 mm 67.8 in.

Family
Manufacturer	Yanmar®
Engine model	3TNV88C-NJT
Engine power (gross)	SAE J1995 rated power: 27.4 kW 36.7 hp 37.2 PS at 2500 rpm
Power take-off (PTO) power	22.7 kW 30.4 hp
Rated engine speed	2500 rpm
Type	Direct Injection
Injection pump type	Direct Injection
Aspiration	Turbocharged
Emissions compliance	Final Tier 4
Cylinders/displacement	Three cylinders: 1.568 L 95.8 cu in.
Number of cylinders	Three
Cylinder liners	Cast-in-block
Bore and stroke	86x90 mm 3.39x3.54 in.
Compression ratio	19.1:1
Lubrication	Pressurized
Cooling system	Water pump
Air cleaner	Dual element
Engine torque at rated speed	104.7 Nm 77.2 lb-ft
Fuel tank capacity	32 L 8.5 U.S. gal.

Battery size	500 CCA
Alternator (12-V)	85 amp
Starter size	1.4 kW 1.9 hp

Standard transmission; forward/reverse	Hydrostatic transmission (HST)
Optional transmission; forward/reverse
Left-hand reverser
Transmission gear ranges
Final drive	Spur gear
Brakes	Wet disc
Steering	Power steering
Clutch, wet/dry
Clutch disk diameter wet clutch
Axle capacity	Front 880 kg 1940 lb Rear 1800 kg 3968 lb
Creeper	No
Cruise control	Standard
Differential lock	Yes
Drawbar maximum vertical load

Type	Open center
Pump rated output	Steering 15 L/min 4 gpm Implement 20.2 L/min 5.3 gpm 35.2 L/min 9.3 gpm
Pump type	Dual gear
Maximum operating pressure	172 bar 2495 psi
Draft control sensing	Position control
Remote control valves available	Up to three

Rollover protective structure	Type Foldable ASABE S478
Platform - flat/straddle	Semi-flat
Gear shift location - console/floor

Compliance
Visibility
Air conditioning, temperature differential
Doors
Noise rating
Seat equipment

Front	R1 Ag 7.00-12 R3 Turf 23x8.50-14 R4 Industrial 23x8.50-14 R3 Turf Radial 200/60 R15
Rear	R1 Ag 12.4-16 R3 Turf 14-17.5 R4 Industrial 14-17.5 R3 Turf Radial 300/70 R20
Front tread range
Rear tread spacing

Model Year 2023 2038RCompact Tractor

SHARE

Features

DOC/DPF

Passive filter cleaning

Active filter cleaning

Parked filter cleaning

Twin Touch foot controls

Integrated hydrostatic pump and motor

Cruise control

Left-side step

Premium seat

2038R Video Gallery

More Videos

Specs & Compare

Add Model

Key Specs

Engine

Electrical

Fuel system

Transmission

Hydraulics

3-point hitch

Power take-off (PTO)

Fluid capacities

Final drive

Operator station

Cab

Dimensions

Tires

Miscellaneous

Additional information

Offers and Discounts

Offers and Discounts

Up to $2,225 off PLUS 0% APR/ACR for 60 months

Get $325 Off†

0% APR/ACR for 60 Months AND Get up to $1,600 off†

3.9% APR/ACR for 84 Months AND Get up to $450 off†

0% APR/ACR for 60 Months†

0% APR/ACR for 72 Months†

15% OFF Select Fall & Winter Attachments†

Related Products

Shop and Buy

Maintenance and Support

You May Also Be Interested In