XUV590EVéhicules utilitaires multisegments

Moteur à essence de 586-cc (35.8- cu in.)

Radiateur

The Gator™ XUV590E Crossover Series Utility Vehicle is powered by a 586-cc (35.8-cu in.), inline twin-cylinder, electronic fuel-injected (EFI) gasoline engine. Ce moteur est commandé électroniquement par un contrôleur de moteur afin d’offrir un rendement optimal.

Il présente les caractéristiques de rendement et de fiabilité suivantes :

• 23.8 kW (32 hp*) at 5600 rpm
• Vitesse maximale de 77 km/h (48 mi/h)
• Injection électronique avec contrôleur du moteur
• Refroidissement par liquide
• Conçu pour le démarrage à froid (testé à -28.9°C [-20°F])
• Système de lubrification à carter humide
• Filtre à huile vissable et dispositif de vidange du carter d’huile accessibles simplement en déposant une plaque de protection, pour un entretien facile
• Filtre à air à grand débit
• Circuit de charge de 875 W (65 A maximum) pour les accessoires (consulter la section sur les moteurs pour voir la courbe du courant de sortie de l’alternateur)
• Silencieux pare-étincelles approuvé par le United States Forest Service (USFS)
• Faible consommation de carburant et grand réservoir de 28 l (7,4 gal)
• Conforme aux normes de l’Environmental Protection Agency (EPA) et du California Air Resources Board (CARB)

* Les renseignements sur la puissance du moteur sont fournis par le fabricant du moteur à des fins de comparaison seulement. La puissance réelle sera moindre.

Tableau de bord et interrupteurs rétroéclairés

Rangement étanche sous le capot

Position ergonomique des commandes

Porte-gobelets dans le tableau de bord et boîte à gants étanche

Rangement optionnel sous le siège pour le modèle S4

• La conception axée sur le conducteur offre une ergonomie et un confort inégalés dans cette catégorie
  • Entrée, sortie et déplacements faciles pour le conducteur et le passager
  • Position assise optimale offrant plus d’espace pour les jambes
  • Ergonomie semblable à celle des voitures
  • Excellent confort pendant la conduite
• Meilleur volume de rangement étanche de sa catégorie de 34 l (9 gal) avec une grande boîte à gants intégrée au tableau de bord et un espace de rangement sous le capot. Un espace de rangement supplémentaire de 34 l (9 gal) est offert sous les sièges des modèles S4.
• Le capot à charnière s’ouvre sans outils et donne accès à un espace de rangement
• Des sièges côte à côte offrent suffisamment d’espace pour un conducteur et un passager
  • Les sièges s’inclinent vers l’avant pour faciliter l’entretien et les tenir au sec lorsque le véhicule demeure à l’extérieur
• Deux porte-gobelets à la portée de la main dans le poste de conduite
• Une prise de 12 V en courant continu est placée à un endroit pratique sur le tableau de bord
• Sept emplacements dotés de capuchons à pression sont déjà percés sur le tableau de bord afin d’accueillir des interrupteurs pour différents accessoires électriques.
• Structure de protection des occupants avec ceintures de sécurité à trois points et une main courante côté passager sur le montant avant
• Démarrage rapide à partir d’une vitesse ou du point mort Le frein de service doit être engagé lors du démarrage

La caisse de chargement est faite d’un composite copolymère de polyéthylène haute densité qui empêche la formation de rouille et de bosses, et atténue le bruit. La grande caisse monopièce a des coins intérieurs arrondis qui permettent la dépose des matériaux lorsqu’elle est inclinée. La caisse en composite est dotée de grosses nervures et est soutenue par une structure en échelle en acier qui assure un excellent rendement pour les tâches ardues et une longue durée de vie. Les trois pièces extérieur très stylisées sont faites de polyoléfine thermoplastique (TPO) pour une durabilité accrue.

Hayon de la caisse de chargement

Poignée du hayon

Pivot du hayon et dispositif de dépose

Cordons de retenue amovibles

Le hayon s’ouvre et se dépose, ce qui facilite le nettoyage et le transport de longs articles. Il possède les caractéristiques d’un hayon de camion et peut être ouvert avec une seule main.

Le point d’articulation du hayon est fait d’acier trempé pour offrir une bonne durabilité et est conçu pour une dépose sans outil. Il est aussi possible de détacher les cordons de retenue de série sans outil afin de déposer le hayon et ainsi faciliter le chargement et le déchargement.

Inclinaison et dépose de la caisse de chargement

Poignée intégrée pour l’inclinaison manuelle de la caisse de chargement (des deux côtés)

Caisse de chargement inclinée

La facilité d’utilisation de la caisse de chargement est essentielle pour réaliser un travail rapide et efficace. La dépose du contenu de la caisse de chargement est facilitée, notamment par le hayon de type camion.The manual release also functions as the lift lever, done in a smooth, one-step motion. La caisse de chargement peut même être inclinée à partir des deux côtés du véhicule. Pour réduire l’effort global du levage, le point d’articulation de la caisse de chargement se situe plus près du centre. Ensemble, les caractéristiques facilitant son utilisation font de cette caisse de chargement la meilleure de sa catégorie.

La caisse peut aussi facilement être déposée pour l’entretien des systèmes du véhicule. Il suffit de déposer deux boulons pour la retirer du châssis du véhicule.

Points d’arrimage intégrés

Point d’arrimage intégré à la caisse de chargement

Points d’arrimage supplémentaires

La caisse de chargement comprend des points d’arrimage intégrés qui augmentent sa polyvalence. Ils se trouvent aux endroits suivants :

• Anneaux en D relevables aux quatre coins intérieurs de la caisse de chargement
• Multiples points le long des bords des parois latérales de la caisse de chargement
• Barres d’arrimage de chaque côté de la caisse avec le colis optionnel de rail de caisse de chargement. Ce colis fournit aussi un système de montage avec des accessoires ayant une bride de serrage rapide de 25,4 mm (1 po).

Accessoires en option

Système de rails pour caisse de chargement

Box mat

Relevage électrique de la caisse de chargement

Rallonge de panneau de caisse de chargement (ici, sur un véhicule utilitaire Gator RSX)

Les accessoires optionnels de la caisse de chargement incluent (consulter les pages de prix ou JDConfigurator pour obtenir la liste complète) :

• Système de rails pour caisse de chargement
• Cargo box mat
• Relevage électrique de la caisse de chargement
• Rallonges de panneau de caisse de chargement
• Support de roue de secours
• Support de benne

Spécifications

ATTENTION : Le transport d’un contenu beaucoup plus long que la caisse peut nuire à sa stabilité.

Détail de la suspension avant du véhicule utilitaire Gator XUV

Les modèles XUV560 et XUV590 sont équipés d’une suspension indépendante aux quatre roues, complémentaire à leur poste de conduite confortable. Cette suspension unique permet un confort de conduite inégalé sur les terrains accidentés et une maniabilité exceptionnelle dans les virages.

L’équipe d’ingénierie a travaillé en collaboration avec des bureaux d’études spécialisés qui conseillent les équipes de Formule 1®, NASCAR®, and INDYCAR® et a mis au point un système de suspension efficace offrant au conducteur un confort de première classe, peu importe le terrain.

Caractéristiques de la suspension avant à double bras triangulaire :

• La conception à double bras triangulaire et arc large assure une maîtrise maximale des roues avant, une direction précise et une garde au sol maximale jusqu’aux roues
• Le débattement des roues de 203 mm (8 po) offre une compression et une extension importantes, qui permettent de maintenir les quatre roues au sol pour une traction supérieure et une meilleure maîtrise du véhicule
• Les amortisseurs à ressort réglables s’adaptent aux terrains les plus exigeants
• La barre stabilisatrice solide et les axes de pivotement et la tringlerie entièrement isolés de caoutchouc sont réglés de façon à offrir la meilleure maniabilité et prévisibilité possible.
• Le carrossage lors de la compression compense le roulis du véhicule et maintient une surface de contact optimale des pneus au sol pour améliorer l’adhérence dans les virages serrés
• La largeur du véhicule augmente pendant la compression pour accroître sa stabilité.
• La fusée et le bras triangulaire supérieur sont en fonte ductile haute résistance ASTM 80-55-06 pour supporter les contraintes élevées des amortisseurs, de l’arbre de transmission à joint homocinétique et des roues
• Les bras triangulaires inférieurs en caisson faits d’acier soudé haute résistance de type automobile réduisent la masse suspendue et augmentent la solidité du dispositif
• Les pivots de torsion des bras triangulaires en caoutchouc sans entretien procurent une longue durée d’utilisation et un fonctionnement silencieux.
• Les bras triangulaires inférieurs en caisson en acier soudé haute résistance de type automobile réduisent la masse non suspendue et augmentent la solidité
• De par sa géométrie antiplongée, la suspension avant constitue une plateforme solide permettant de freiner en toute confiance.
• La géométrie optimisée de la direction par suite de la simulation ADAMS CAR minimise l’effort de direction et augmente la sensibilité de celle-ci en fonction du terrain

Détail de la suspension arrière du véhicule utilitaire XUV

Voici les caractéristiques de la suspension arrière indépendante :

• Le débattement des roues de 203 mm (8 po) offre une compression et une extension importantes, qui permettent de maintenir les quatre roues au sol pour une traction supérieure et une meilleure maîtrise du véhicule
• La conception unique et indépendante de la suspension arrière offre un excellent confort de conduite et une bonne protection des arbres de tramnsmission à joint homocinétique.
• Les amortisseurs à ressort réglables s’adaptent aux terrains les plus exigeants
• Le carrossage lors de la compression compense le roulis du véhicule et maintient une surface de contact optimale des pneus au sol pour améliorer l’adhérence dans les virages serrés
• La largeur du véhicule augmente pendant la compression pour accroître sa stabilité.
• La fusée de roue, le bras triangulaire inférieur et le maillon supérieur sont en fonte ductile haute résistance ASTM 80-55-06 pour supporter les contraintes importantes des amortisseurs, de l’arbre de transmission à joint homocinétique et des roues, et ont la robustesse nécessaire pour encaisser l’impact d’un rocher
• Les pivots de torsion des bras triangulaires en caoutchouc sans entretien procurent une longue durée d’utilisation et un fonctionnement silencieux.

NASCAR est une marque de commerce de NASCAR. INDYCAR est une marque de commerce de Brickyard Trademarks Incorporated. Formule 1 est une marque de commerce de Formula One Licensing BV, une entreprise de Formula One Group.

Les amortisseurs Fox™ en option sont disponibles en pose en usine

Amortisseurs de course monotube haute pression en aluminium exclusifs FOX Racing

• Précharge de ressort entièrement réglable pour différents styles de conduite
• Un piston flottant interne sépare l’azote haute pression de l’huile d’amortissement. Cette séparation évite l’aération (moussage) et la dégradation de la viscosité de l’huile, ce qui améliore l’uniformité de l’amortissement et évite la diminution du rendement.
• La production de pression et de chaleur dans le monotube est inférieure à celle que l’on retrouve dans les amortisseurs bitubulaires classiques, ce qui permet un meilleur contrôle du véhicule dans des conditions de conduite rigoureuses.
• L’enveloppe unique en aluminium du monotube permet un rejet de chaleur plus efficace et diminue le total de la masse non suspendue.
• Le montage de l’extrémité de l’arbre de l’amortisseur sur le bras de suspension diminue la masse non suspendue du système de suspension, ce qui en améliore la réaction.

NASCAR est une marque de commerce de NASCAR. INDYCAR est une marque de commerce de Brickyard Trademarks Incorporated. Formule 1 est une marque de commerce de Formula One Licensing BV, une entreprise de Formula One Group.

StarFire™ 3000 Receiver and GreenStar™ display (GS) installed on Gator™ RSX

The AMS integration kit allows the operator to mount a StarFire receiver and GS display (both receiver and display sold separately) to the Gator Utility Vehicle.

Key features of the AMS integration kit:

• Compatible with StarFire iTC™ and 3000 Receivers
• Compatible with GS2 1800, GS2 2600, and GS3 2630 Displays
• GS display mounts to the occupant protective structure (OPS) for convenient access
• Ability to mount receiver to the poly roof, or on the OPS alone
• Switched power to receiver and display allows the operator to run the AMS equipment even when the vehicle’s ignition is off. Receiver and display will not turn off when the vehicle’s ignition is turned on and off.

Common applications:

• Boundary mapping
• Flagging field obstacles
• Soil sampling

Compatibility:

• Compatible with Gator XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Gator Utility Vehicles. Compatible with full windshield, poly cab.

Backup alarm components

A must for any worksite, the backup alarm kit alerts pedestrians when the Gator™ Utility Vehicle is operating in reverse. This kit includes an alarm, mounting bracket, wire harness, and switch. Does not include grease.

Front CV guards

Rear CV guards

CV guards add additional protection for the A-arms, brake lines, and CV half shafts:

• Aluminum guards handle impacts while maintaining a low, unsprung mass
• Includes front and rear guards
• Easily bolts to the A-arms with three bolts per corner (12 bolts total)
• Drainage holes provided to prevent buildup of dirt, grass, and other loose materials

Gator™ XUV 550, shown with front brushguard and Hella® performance spot lights (BM24108)

The front brushguard for the Gator XUV 550, XUV550 S4, XUV560, XUV560 S4, XUV590, and XUV590 S4 not only looks great, but it is also tough enough to take on the toughest terrain:

• The aggressive appearance is no accident – the brushguard is made of large-diameter, 1.75-in. (44.45-mm) tubing and thick steel plates to protect the critical elements of the front of the vehicle, including the grille, lights, and hood.
• Possesses welded brackets for quick installation of the Hella light kits
• Rotates forward without tools for easy access to service points and additional storage under the hood
• Design permits easy access under hood without modification
• Design provides good approach angle for leveraging over obstacles in front of vehicle
• Removable plate permits installation of optional winch and front receiver

Hella is a trademark of Hella KG Heuck & Co.

Shown on Gator™ XUV 550 with optional front brushguard and HELLA® performance spotlights

Tire shown at angle

Protect the Gator XUV 550, XUV550 S4, XUV560, XUV560 S4, XUV590, and XUV590 S4 by adding front fender guards to the vehicle. Large, 44.45-mm (1.75-in.) diameter tubing provides superb protection for the front grille, lights, and fenders.

HELLA is a trademark of HELLA KG Hueck & Co.

Nerf bars

Add additional protection to the Gator™ XUV590 or RSX Utility Vehicle.

• Adds extra protection to chassis and body panels
• Easy to install

Nerf bars

Add additional protection to the Gator™ XUV590E/M, XUV560E/M or RSX860E/M Utility Vehicle.

• Adds extra protection to chassis and body panels
• Easy to install

Shown on Gator™ XUV 550

Rear bumper detail

Add additional protection to the rear of the Gator XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicle by adding BM23362 rear bumper.

Cargo box pail holder

Cargo box pail holder

The 5-gal. (18.9-L) pail holder is ideal for operators who want to maximize the work capability of their Gator™ Utility Vehicle. The 5-gal. (18.9-L) pail holder keeps pails in place within the cargo box, ensuring that they stay safe and secure. Featuring the quick-clamp mounting system, it mounts easily to the cargo rails of the cargo box with just one clamp.

Shown on Gator™ XUV 550

The cargo box bed mat not only protects the floor of the cargo box from scratches and dents, but it also provides additional cushioning and slip resistance to items being hauled in the cargo box.

Cargo box power lift installed

Backlit dash-mounted switch for easy operation

The Gator™ XUV Series can be equipped with an optional power lift for the cargo box. This is one of the most important accessories for increasing work efficiency. It is an excellent complement to this highly capable utility vehicle.

The power lift offers the following features:

• Linear actuated
• Capable of lifting a maximum vehicle cargo box load of 182 kg (400 lb)
• Lifts box to 45 degrees from horizontal for ease of service and cargo box load removal
• Quick horizontal-to-45-degree time
• Can be installed in minutes using the vehicle's prewired connectors and mounting points
• Compact design fits nicely around transmission and linkages, providing full protection
• Weather-resistant enclosure and seals (IP 65 capable)
• Driven by 12-VDC motor
• Motor is protected with auto reset breaker inside the motor housing

Shown on Gator™ XUV 550

Increase the versatility of cargo box on Gator XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles by adding cargo box rails. These sturdy rails attach easily to the cargo box, and allow for a variety of accessories to be added and removed with ease.

For use with select accessories featuring the 25-mm (1-in.) quick-clamp mounting system.

Increase the cargo capacity of Gator™ XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles by adding cargo box wall extensions to the cargo box. This accessory is easy to attach to, and remove from, the cargo box rails, thanks to the quick-clamp mounting system. The tailgate is able to be opened and closed while the extensions remain in place, allowing for easy dumping.

NOTE: Not compatible with operator protection system (OPS) poly cab.

Cargo box side extension kit (required, sold separately)

Cargo box side extension cover

Tailgate down, side extension flipped up

Key features:

• The cover closes off the top of the side extensions, ideal for hauling hunting dogs, and small animals
• Easily attaches to the side extension kit (required, sold separately)
• Dimensions: 47.6” (120.9 cm) wide x 25” (63.6 cm) tall x 32.3” (82.4 cm) deep

Compatibility:

• Gator™ XUV 550, XUV 550 S4, XUV560E/M, XUV560E/M S4, XUV590E/M, XUV590E/M S4, and RSX860E/M Utility Vehicles

Spare tire rack

The spare tire rack is ready to be put to good use if the terrain claims a tire. The tire rack will hold either the front or rear tire. It mounts to both the cargo bed and the cargo box rails (required) to keep the spare tire secured through the roughest terrain.

Compatible with Gator™ RSX, XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, and XUV590 S4 Utility Vehicles.

21 Steel Utility Cart

The 21 Steel Utility Cart is the ideal companion for the Gator™ Utility Vehicle:

• 454-kg (1000-lb) load limit
• Dump angle of 35/40 degrees
• Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
• Large pneumatic tires
  • Provide good flotation in mud, sand, and other wet or soft areas
  • Flex over bumps and ruts for a smoother, more controlled ride
  • Minimize ground compaction to save turf and prevent ruts in soft ground
• Unique bracket less tailgate means no side channels to obstruct materials when emptying
• When shoveling, recessed flat bolt heads stay out of the way
• Heavy-duty, reinforced one-piece solid undercarriage
• Contoured corner bed design
• Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1-7/8-in.) ball hitch, including Gater™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models

Ordering information

Contact the local John Deere dealer for availability and pricing information.

21 Steel Utility Cart
Order number: LPUT21JD

Gator XUV560/590i front seat cover - black

Available through OrderZone

Each kit contains one bench base cover, one backrest cover, and installation instructions.

Special Features:

• Exceptional abrasion, tear, and puncture resistance
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Available in black or REALTREE HARDWOODS HD® pattern
• Front seat has modular lightweight load-carrying equipment (MOLLE) webbing between driver and passenger for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Compatible with Gator XUV560i and XUV590i Utility Vehicles.

REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited. Cordura is a trademark of Invista.

Gator XUV560/590i front seat cover - camo

Available through OrderZone

Each kit contains one bench base cover, one backrest cover, and installation instructions.

Special Features:

• Exceptional abrasion, tear, and puncture resistance
• Constructed with military-grade Cordura™ fabrics
• Protects original equipment manufacturer (OEM) seats from mud, snow, and debris
• Quick and easy installation
• Available in black or REALTREE HARDWOODS HD® pattern
• Front seat has modular lightweight load-carrying equipment (MOLLE) webbing between driver and passenger for MOLLE pouches
• Limited 1-year warranty
• Made In U.S.A.

Compatible with Gator XUV560i and XUV590i Utility Vehicles.

REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited. Cordura is a trademark of Invista.

Front seat cover - yellow

A yellow front seat cover for Gator™ utility vehicles is available through Order Zone. 

Special features:

• Protect seats from mud and stains
• Cushioned for extra comfort
• Includes pockets for storing tools and gear
• Easily adjusted elastic hem cord closure for a more custom fit
• Easy access to seatbelts
• Large-capacity, zippered, rear mesh cargo pocket
• Compatible with the XUV560 and XUV590
• Includes covers for the bench and base (two-piece set)
• Limited 2-year warranty

Vehicle cover - black

• Provides year-round weather protection to a vehicle equipped with an operator protection system (OPS), rollover protective structure (ROPS) or full enclosure (cab)
• Heavyweight polyester fabric for maximum durability and resistance to tears
• Polyurethane-coated for maximum water resistance and repellency
• Dual-reinforced air vents let air circulate and help to prevent ballooning in wind
• Reinforced rear corners for added durability 
• Elastic shock cord in the bottom hem for a quick custom-like fit
• Compatible with Gator™ XUV 550, XUV560, XUV590, and RSX Utility Vehicles

Ordering information

Contact the local John Deere dealer for availability and pricing information.

Vehicle cover - black
Order number: LP37036

Transportable vehicle cover - black

All-season protection against sun damage, rain, dust, and tree sap. Additionally:

• Black
• Dual-reinforced air vents let air circulate and help prevent ballooning in winds
• Reinforced corners for added durability
• Tension panels allow cover to be used while trailering
• Heavy-duty coated fabric will not stretch for maximum water resistance and repellency
• Elastic cord in bottom hem for a quick and custom fit
• Fits all Gator™ HPX, XUV 620i, XUV 625i, XUV 825i, XUV 855D, XUV 550, XUV560, XUV590, and RSX Utility Vehicles

Ordering information

Contact a local John Deere dealer for availability and pricing information.

Transportable vehicle cover - black

Order number: LP37040

Transportable vehicle cover - camo

All-season protection against sun damage, rain, dust, and tree sap. Additionally:

• Camo
• Dual-reinforced air vents let air circulate and help prevent ballooning in winds
• Reinforced corners for added durability
• Tension panels allow cover to be used while trailering
• Heavy-duty coated fabric will not stretch for maximum water resistance and repellency
• Elastic cord in bottom hem for a quick and custom fit
• Fits all Gator™ HPX, XUV 620i, XUV 625i, XUV 825i, XUV 855D, XUV 550, XUV560, XUV590, RSX Utility Vehicles

Ordering information

Contact a local John Deere dealer for availability and pricing information.

Transportable vehicle cover - camo

Order number: LP37041

Receiver hitch and recovery loops shown installed

Rugged and versatile, this is not an ordinary front receiver hitch. Made from welded steel, the recovery loops are strong enough to pull even the toughest loads, and are perfect for securing the vehicle to a trailer. This receiver hitch serves as the platform for the winch base. The receiver-type front hitch accepts the 51-mm (2-in.) drawbar (sold separately).

Required for mounting BM23995 (Warn® winch – Gator™ XUV 550), BM24019 (Warn winch – XUV 550 S4), BM26248 (Warn winch – XUV560, XUV560 S4, XUV590, XUV590 S4), and BM24437 (Warn winch – RSX Utility Vehicle).

Warn is a trademark of Warn Industries, Inc.

48-mm (1-7/8-in.) ball hitch shown

The 51-mm (2-in.) ball hitch attaches to the drawbar or rear hitch to allow towing.

The ball hitch is available through Service Parts.

48-mm (1-7/8-in.) hitch ball

The 48-mm (1-7/8-in.) ball hitch attaches to the drawbar or rear hitch to allow towing.

The ball hitch is available through Service Parts.

Drawbar kit for receiver hitch

Description:

• Kit includes a 51-mm (2-in.) drawbar, 10-mm (0.39-in.) pin, and hair cotter pin
• Steel construction has a 25-mm (1-in.) ball hole size
• Can be mounted in the standard rear receiver hitch or the optional front receiver hitch
• Compatible with all Gator model year 2011-current XUV560, XUV560 S4, XUV590, XUV590 S4, XUV 625i, XUV 825i, XUV 855D, RSX860, and M-Gator™ A2 Utility Vehicles
• Compatible with XUV 620i and XUV 850D Utility Vehicles

NOTE: Compatible with all Gator HPX Utility Vehicles if equipped with an optional 51-mm (2-in.) front receiver hitch. An optional 51-mm (2-in.) rear receiver is not available for the Gator HPX models. A 32-mm (1-1/4-in.) rear receiver hitch and drawbar are available for the Gator HPX models.

Shown on XUV 550 S4

Expand the work capabilities and cargo capacity of Gator™ XUV 550, XUV550 S4, XUV560, XUV560 S4, XUV590, and XUV590 S4 by adding the front rack. Made of heavy-duty materials, the front rack not only increases the functionality of the Gator, it is also designed to enhance the aesthetics of the vehicle. This generously sized rack, 1270-mm (50-in.) long by 381-mm (15-in.) wide by 102-mm (4.5-in.) deep - outside dimensions, will haul up to a 45.4-kg (100-lb) payload.
 
The rack easily mounts to the required front brush guard. Once the rack is mounted, it tilts forward in conjunction with the brush guard to allow full access to under-hood storage and service points.

MOLLE device pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Velcro flap closure
• Padded to protect device and contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6-in. (152.4-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE device pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Velcro flap closure
• Padded to protect device and contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6-in. (152.4-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE fire extinguisher pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Military-grade rapid extraction clips
• Fits standard round 2.5-lb (1.1-kg) fire extinguishers
• Padded to protect contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6–in. (152.4-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE fire extinguisher pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Military-grade rapid extraction clips
• Fits standard round 2.5-lb (1.1-kg) fire extinguishers
• Padded to protect contents
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 6–in. (152.7-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE large storage pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 5–in. (127-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE large storage pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Dual military-grade zippers and pulls
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 5–in. (127-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Built-in drain hole
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE small storage pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 5–in. (127-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

MOLLE small storage pouch

Available through OrderZone

Compatible with bench seat covers and operator protection system (OPS) MOLLE storage panel

Special features:

• Military-grade zippers and pulls
• Constructed with military-grade Cordura™ fabrics
• Utilizes the MOLLE attachment system
• Pair of 5–in. (127-mm) MOLLE sticks included
• Available in black or REALTREE HARDWOODS HD™ pattern
• Inner liner made of high-density coated pack-cloth nylon fabric
• Limited 1-year warranty
• Made In U.S.A.

Cordura is a trademark of INVISTA for durable fabrics. REALTREE HARDWOODS HD is a trademark of Jordan Outdoor Enterprises Limited.

Heater kit

Heater kit

The heater kit conveniently mounts under the storage tub, and provides both heat and defrost.

Parts in the kit:

• Heater core and blower
• Wire harness
• (2) 2-in. (25-cm) adjustable vents
• Windshield vent
• Three-position blower switch (off, low, high)
• Mounting hardware

Horn components

Kit includes:

• Horn
• Mounting brackets
• Wire harness and switch

The switch mounts on the dash of the vehicle, while the wiring harness connects to the main vehicle harness.

Beacon light

Features and benefits:

• 3-in. (76-mm) round, light-emitting diode (LED) strobe light provides excellent visibility for vehicle bystanders
• Especially useful for working around properties and job sites
• Acrylic amber lens resists scratching and scuffing
• Impact-resistant nylon housing
• SAE J845 (Class 3)-compliant
• UL recognized
• Stands 4.4 in. (111.5 mm) tall

Compatible with the following vehicles:

• Model year 2006 to current Gator™ HPX Utility Vehicles
• Requires poly roof and operator protection system (OPS) switch bank for mounting
• Requires beacon light harness kit
• Gator XUV 620i and 850D Utility Vehicles
• Requires poly roof and OPS switch bank for mounting
• Requires beacon light harness kit
• Model year 2011 to current Gator XUV 625i, 825i, 825i S4, 855D, and 855D S4 Utility Vehicles
• Requires poly roof and OPS switch bank for mounting
• Requires beacon light harness kit
• Gator XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590i, XUV590i S4 Utility Vehicles
• Requires OPS switch bank and brake/tail light for brake light mounting or OPS switch bank and poly roof for roof mounting
• Requires beacon light harness kit
• Gator RSX Utility Vehicles
• Requires OPS switch bank and brake/taillight for brake light mounting or OPS switch bank and poly roof for roof mounting
• Requires beacon light harness kit

Beacon light harness kit (shown on Gator™ XUV560)

The beacon light harness kit is required when installing the beacon light.

The kit includes the switch to mount in the operator protection system (OPS) switch bank and wire harness between the OPS switch bank and beacon light.

Brush guard light harness kit

The brush guard light harness kit is required when installing the light kits to the brush guard or PreRunner bumper on the Gator™ RSX.

The kit includes the switches and wire harnesses.

Front OPS / roof light harness kit

The front OPS/roof light harness kit is required when installing the light kits to the front of the OPS or roof. Also requires OPS switch bank.

The kit includes the switch and wire harnesses from the OPS switch bank to the lights.

Roof mounted

Brush guard mounted

Rigid Industries LED driving lights (two lights per kit)

Lux = measure of intensity of light that hits or passes through a surface

Mounted on the front operator protection system (OPS)/roof or brush guard for extreme night driving lights.

LED light specifications:

• 50,000+ hour lifespan
• IP69K certified
• Polycarbonate lens
• Aluminum housing
• Powder-coat finish
• Sealed Deutsch connectors
• Operating Temp -40°F – 145°F
• MIL810-STDG vibration certified
• ASTMB117 salt / fog certified
• Standard black lens covers

The LED lights are compatible with the HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, XUV560, XUV560 S4, XUV590i, XUV590i S4, RSX Utility Vehicles.

These lights are not compatible with Jensen radios or deluxe cab frame.

The LED lights can be mounted on the brush guard, roof (front or rear), or directly on the OPS (front or rear). Roof or OPS mount requires the OPS Switch Bank.  The LED light kits also require the necessary Light Harness Kit based on the desired light mounting location:

Front OPS/roof light harness kit

Rear OPS/roof light harness kit

Brush guard light harness kit

Roof mounted

Rigid Industries LED work lights (two lights per kit)

Lux = measure of intensity of light that hits or passes through a surface

Ideally mounted on the front or rear operator protection system (OPS)/roof for light around the vehicle to work at all hours of the night.

LED light specifications:

• 50,000 or more hour lifespan
• IP69K certified
• Polycarbonate lens
• Aluminum housing
• Powder-coat finish
• Sealed Deutsch connectors
• Operating temperature - 40°F – 145°F (4°C-63°C)
• MIL810-STDG vibration certified
• ASTMB117 salt / fog certified
• Standard black lens covers

The LED lights are compatible with the Gator™ HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, XUV560, XUV560 S4, XUV590i, XUV590i S4, RSX Utility Vehicles.

These lights are not compatible with Jensen radios or deluxe cab frame.

The LED lights can be mounted on the brush guard, roof (front or rear), or directly on the OPS (front or rear). Roof or OPS mount requires the OPS switch bank.  The LED light kits also require the necessary light harness kit based on the desired light mounting location:

Front OPS/roof light harness kit

Rear OPS/roof light harness kit

Brush guard light harness kit

OPS with power wire and switch bank

Switch bank (detail)

Product attributes:

• Accommodates up to three sets of OPS lights
• Allows for simple wire routing - only two wires run through the OPS or roll-over protective structure (ROPS) tubes; each light kit has its own switch and wiring harness
• Switches are located in the OPS or rollover protective structure (ROPS)

Compatible with:

• Model year 2011 - current Gator™ XUV, HPX Gas, HPX Diesel, and M-Gator A2 Non-Military Utility Vehicles
• Model year 2012-2013 Gator XUV 550, XUV 550 S4, and RSX Utility Vehicles
• Model year 2013 - current Gator XUV 825i S4 and XUV 855D S4 Utility Vehicles
• Current Gator XUV560, XUV560 S4, XUV590, and XUV590 S4 Utility Vehicles

Rear OPS / roof light harness kit

The rear OPS/roof light harness kit is required when installing the light kits to the rear of the OPS or roof. Also requires OPS switch bank.

The kit includes the switch and wire harnesses from the OPS switch bank to the lights.

Work lights (rear mounted)

Increase the capability of the Gator™ Utility Vehicle by adding work lights. Lights mount to the front or rear of the poly roof or directly to the operator protection system (OPS).

Kit includes the pair of work lights and hardware. Requires necessary light harness kit based on desired mounting location.

Lights can also be installed in a low mount position behind the front bumper.

Product attributes:

• This flood light kit provides a wide range of light, making it ideal for tasks at night
• Especially useful for working around properties and job sites
• Requires OPS switch bank when mounted to roof or OPS

Compatible with:

• XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590i, XUV590i S4
• HPX
• XUV 625i, XUV 825i, XUV 825i S4, XUV 855D, and XUV 855D S4
• RSX Utility Vehicles

Shown mid-size XUV

The OPS rearview mirror for Gator™ Utility Vehicles can be installed when equipped with an OPS.

The rearview mirror can be positioned in multiple locations on the OPS and offers expanded visibility for the operator.

Product attributes include:

• Composite components made of impact resistance materials
• Installs with quick clamp to OPS tube
• Compatibility with all Gator Utility Vehicles equipped with an OPS

Shown on Gator™ HD XUV

Shown on HD XUV

The OPS side mirrors for Gator Utility Vehicles can be installed when they are equipped with OPS.

The side mirrors can be positioned in multiple locations on the OPS and offers expanded visibility for the operator.

Product attributes include:

• Composite components made of impact-resistant materials
• Installs without tools and easily adjustable
• Compatibility with all Gator HPX, XUV 620i, XUV 850D, XUV 625i, XUV 825i, XUV 825i S4, XUV 855D, XUV 855D S4, XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, RSX, M-Gator A2, and M-Gator A3 Utility Vehicles equipped with an OPS

NOTE: OPS side mirrors are not compatible with the deluxe cab or poly cabs (poly cabs include standard mirrors).

Shown on Gator™ XUV550 Utility Vehicle

Shown on RSX

The side mirrors are secured to the poly door and offers expanded visibility for the operator.

Product attributes include:

• Composite components made of impact-resistant materials
• Easily adjustable
• Compatibility with all Gator XUV550, XUV550 S4, and RSX Utility Vehicles equipped with the poly cab doors

Comfort straps

Kit includes two comfort straps for the left and right seat belts.

• Provides relief to the operator's and passenger's upper body when driving over rough terrain by allowing the seat belt to stretch when the seat belt locks
• Moves the upper mounting point of the seat belt down 6 in. (152 mm)
• Can be mounted to both the driver- and passenger-side upper mounting point of the three-point seat belt
• Compatible with all model year 2017 - current Gator™ HPX, XUV625i, XUV825i, XUV825i S4, XUV855D, XUV855D S4, XUV560, XUV560 S4, XUV590i, XUV590i S4, and RSX860i Utility Vehicles when equipped with standard Occupant Protective Structure (OPS)
• Compatible only with standard Occupant Protective Structure (OPS), for deluxe cab frame, order BM22703

Canvas cab doors

Features of the canvas cab doors:

• Made from premium, heavy-duty 600 denier-solution dyed, water-resistant polyester with UV stabilizers, for mold and tear resistance
• Durable PVC window resists yellowing or cracking. Window opens easily with a zipper and can be secured in place with straps.
• Automotive-style handle and latch for easy entry
• Aluminum inner frame for strength and to reduce weight of door
• Integrated storage pockets
• Installs in minutes with basic tools
• These doors are meant to be for basic weather protection, the doors do not have a bulb seal, therefore do not seal tightly against the operator protection system (OPS) frame like the poly cab doors.
• Compatible with full poly windshield, glass windshield, poly roof, canvas roof/rear panel (if poly windshield is installed), rear panel, poly rear window

Floor mats

This washable rubber floor mat provides an added layer of protection to the floor of the vehicle and guards against dents, dings, and scratches.

Kit comes with front left and right floor mats.

Glove box lock (locked position)

Glove box lock (unlocked position)

Keep gear secure by adding the BM24200 glove box lock to Gator™ XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles.

OPS net

The OPS net kit is a replacement for the factory-installed occupant side retention (OSR) nets, or can be installed on vehicles that had the OSR doors installed from the factory.

Compatible with model year 2016 or later Gator™ XUV560 and two-passenger XUV590 Utility Vehicles.

• OPS certified to SAE J2194
• Nets meet ANSI B71.9 certification
• Nets feature one-handed operation, easy entry/exit, and great visibility

OPS rear panel (shown with poly roof, deluxe light kit, rear-mounted mid-range light kit)

The OPS rear panel for the OPS poly cab is ideal for outdoor enthusiasts and others desiring four-season weather protection.

The poly cab can be sold as individual components; OPS poly or glass windshield, OPS poly roof, OPS rear panel, and doors kit. This gives operators the flexibility to configure the vehicle to meet their unique needs.

The OPS rear panel can be coupled with the half or full windshield to help reduce dust and airflow in the operator’s station.

Key features of the rear panel:

• Rear panel is thermoformed from thick acrylonitrile butadiene styrene (ABS) plastic for impact resistance, durability, and style
• Three-piece sliding glass window, which provides excellent visibility and ventilation
• Installs in minutes with quick clamps to the OPS structure

Compatible with:

• XUV 550, XUV560, and XUV590 Utility Vehicles
• RSX Utility Vehicles

Shown on Gator™ XUV 550 (front)

Shown on XUV 550 (rear)

Product attributes:

• Provides additional protection to the operator and passenger when a Gator™ XUV 550, XUV560, or XUV590 Utility Vehicle is equipped with an OPS
• Perforated, black metal screen is easy to attach to, and remove from, the side and upper tubes of the OPS with the quick clamp mounting system
• Compatible with all Gator model year 2012-current XUV 550, XUV560, and XUV590 Utility Vehicles when equipped with an OPS

Poly cab door closeout panels

The poly cab door closeout panels are required on the Gator™ XUV590i and XUV590i S4 Utility Vehicles when the poly cab doors are installed on the vehicle. These closeout panels provide the close off between the poly cab doors and styled components and fuel tank.

Not required on the Gator XUV560 or XUV560 S4.

Poly doors

The poly doors kit for the operator protection system (OPS) poly cab is ideal for outdoor enthusiasts and others desiring four-season weather protection. It is designed to conform and integrate with the Gator™ XUV550, XUV560, and XUV590 Utility Vehicles equipped with OPS.

For a complete poly cab, the user would also order the poly roof, and one of the three following windshields.  When installed on the XUV590, the rear panel is also required.

• OPS full poly windshield
• OPS full abrasion-resistant flip-out windshield
• OPS glass windshield with wiper

Sport steering wheel

The must-have option to give the Gator™ RSX, XUV560, XUV560 S4, XUV590, and XUV590 S4 Utility Vehicles the customization they deserve. Color accents and a comfortable feel make this a must have for the sport enthusiast.

Installed stereo and speaker kit

Enhance the Gator™ XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles by adding the stereo and speaker kit. The kit includes lights (not including brake light shown above), speakers, and a convenient netted pouch for extra storage.

The stereo and speaker kit can be easily mounted to the operator protection system (OPS) or rollover protective structure (ROPS) with the quick clamp mounting system. The waterproof top allows this kit to be used without a poly roof; however, it can be used with the poly roofs as well.

The operator must choose one of the following three head units to have complete stereo:

• SWJHD1120 stereo, heavy-duty AM/FM/weatherband/auxiliary
• SWJHD1620 stereo, heavy-duty AM/FM/weatherband//SiriusXM® satellite/iPod® device ready
• SWJHD3620 stereo, heavy-duty AM/FM/weatherband/CD/SiriusXM satellite/USB 2.0
• SWJDABIPDL iPod adaptor cable for SWJHD1620 and SWJHD3620

NOTE: Must order head unit through Parts.
NOTE: Installation requires AM140972 harness.

iPod is a trademark of Apple, Inc.  Sirius is a trademark of Sirius XM Radio Inc.

SWJHD1120 stereo head unit

SWJHD1620 stereo head unit

SWJHD3620 stereo head unit

Canvas roof/rear panel shown with canvas doors and full flip-out poly windshield

Canvas roof/rear panel

Features of the canvas roof/rear panel:

• This canvas roof/rear panel is a single-piece construction that mounts to the top and rear of the operator protection system (OPS)
• Made from premium, heavy-duty 600 denier-solution dyed, water-resistant polyester with UV stabilizers, for mold and tear resistance
• Durable PVC window resists yellowing or cracking. Window opens easily with a zipper and can be secured in place with straps
• Installs in minutes
• Compatible with canvas doors on Gator™ XUV590i Utility Vehicles
• Compatible with poly doors
• Compatible with full flip-out poly windshield
• Not compatible with glass windshield

Shown on mid-size XUV with additional attachments

The OPS poly roof provides all-year-round weather protection to the operator and passenger. This roof is compatible with model year 2012-current mid-size XUV’s and RSX Utility Vehicles.

Features and benefits:

• Features the OPS quick-clamp mounting system; the one-piece ABS roof easily attaches/detaches to the vehicles OPS or roll-over protective structure (ROPS) with four clamps
• Sturdy design allows for the Gator to be towed at highway speeds while the roof is installed
• Useful for minimizing sun exposure to the operator, passenger, and vehicle operating station
• Molded-in water troughs route water away from the operator and passenger
• Acts as the foundation to build an OPS poly full cab enclosure (designed to work with the OPS full windshield kits, OPS poly rear panel and doors kit)
• Compatible with a variety of OPS lights kits

Shown on Gator™ XUV camo, with optional brake and tail light kit, OPS rear screen, and OPS half windshield (front)

Shown with optional brake and tail light kit, OPS rear screen, and OPS half windshield (back)

The OPS poly roof – camo provides all-year-round weather protection to the operator and passenger.

Features and benefits:

• Features the OPS quick-clamp mounting system; the one-piece ABS roof easily attaches/detaches to the vehicles operator protection system (OPS) or rollover protective structure (ROPS) with four clamps. No tools required.
• REALTREE HARDWOODS HD® camo pattern matches the camo Gator XUV Utility Vehicle
• Sturdy design allows for the Gator XUV 550, XUV590, or RSX to be towed at highway speeds while the roof is installed
• Useful for minimizing sun exposure to the operator, passenger, and vehicle operating station
• Molded-in water troughs route water away from the operator and passenger
• Acts as the foundation to build an OPS poly full enclosure (designed to work with the OPS poly full windshield kit and OPS poly rear panel and doors kit)
• Compatible with a variety of OPS lights kits

REALTREE HARDWOODS HD is a U.S.-registered trademark of Jordan Outdoor Enterprises Limited

Speed limiter

The Gator™ XUV590i and XUV590i S4 Gator Utility Vehicles are equipped with electronic fuel injection (EFI), controlled by an electronic controller unit (ECU).

Utilizing this ECU and the speed limiter kit, the top speed of the vehicle can be limited to 28 mph (45 km/h).

The speed limiter offers the following:

• Mounts directly in the glove box
• Limits top speed to 28 mph (45 km/h) in the ON position without having to operate the vehicle in low gear
• Vehicle has full acceleration and work capability between 0 mph to 45 mph (72 km/h) when the speed limiter is in the OFF position
• Controlled with a key that can be removed in the ON or OFF position
• Two keys per kit

25-gal. (94.6-L) bed sprayer

The 25-gal. (94.6-L) Gator™ bed sprayer is designed to work with the XUV 550 and RSX Series Gator vehicles. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and deicer. It comes complete with a 43-in. (1.1-m) boom that sprays a 120-in. (3-m) swath. It is equipped with a 19-ft (5.8-m) hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable, brass spray wand tip achieves streams up to 30 ft (9 m). It comes equipped with rubber feet and custom brackets, which secure to the Gator bed for a no-tools mount.

Special features:

• 25 gal. (94.6 L) capacity
• Includes sprayer remote control for added convenience
• Brackets secure to Gator bed, no bungee or straps required
• No-tools mounting (after initial install)
• Convenient side mount hose wrap

This product requires accessory wire harness (AM140972) sold through John Deere.

Additional features:

• 100 psi SHURflo® diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage
• The fully adjustable, brass spray wand tip achieves streams up to 30 ft (9 m)
• Equipped with a 19-ft (5.8-m) hand-wand hose with side-mount hose tender for convenience
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• Remote control on/off switch with 100-ft (30-m) range
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill-level indicators (in gallons)

Ordering information

Contact a local John Deere dealer for availability and pricing information.
 

SHURflo is a trademark of SHURflo, LLC.

45-gal. (170.3-L) bed sprayer

The 45-gal. (170.3-L) Gator™ bed sprayer is designed to work with the Gator XUV 550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Series Utility Vehicles. It provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and deicer. It comes complete with a 43-in. (1.1-m) boom that sprays a 120-in. (3-m) swath. It is equipped with a 19-ft (5.8-m) hose and a spray wand for spot spraying lawns, shrubs, trees, etc. The fully adjustable brass spray wand tip achieves streams up to 30 ft (9 m). It comes equipped with rubber feet and custom brackets, which secure to the Gator bed, for a no-tools mount.

Special features:

• 45-gal. (170.3-L) capacity
• Includes sprayer remote control for added convenience
• Brackets secure to Gator bed, no bungee or straps required
• No tools mounting (after initial install)
• Convenient side mount hose wrap

This product requires accessory wire harness (AM140972) sold through John Deere.

Additional features:

• 100 psi SHURflo® diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage.
• The fully adjustable brass spray wand tip achieves streams up to 30 ft (9 m)
• Equipped with a 19-ft (5.8-m) hand wand hose with side mount hose tender for convenience
• Check valves in boom tips prevent siphoning and dripping, which can cause lawn spotting
• Remote control on/off switch 100-ft (30.5-m) range
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Ordering information

Contact the local John Deere dealer for availability and pricing information.

SHURflo is a trademark of SHURflo, LLC.

45-gal. (170.3-L) high-performance bed sprayer

The high-performance bed sprayer is designed to work with Gator™ XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles. With a 45-gal. (170.3-L) capacity, high-volume electric pump, and premium pistol-grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and deicer. It is the perfect match for the operator who wants extreme performance. Custom brackets secure the sprayer to the cargo bed for a no tools mount. Cover ground quickly with flexible boom options; a 150-in. (3810-mm) precision folding, 120-in. (3048-mm) standard 3-tip, 30-ft (9.1-m) boomless, or no boom at all (boom sold separately).

High-performance features:

• 45 psi, 3.6 gpm SHURflo™ diaphragm-type pump is designed for high-hour applications and can be run dry without damage
• Premium pistol-grip spray gun, designed for single-hand mist to 35-ft (10.7-m) stream
• Side-mount hose tender for easy hose access and storage
• Glycerin-filled pressure gauge
• TeeJet™ pressure regulation/recirculation valve
• Includes sprayer remote control (LP22912)

Boom options (sold separately): 

• Choice of standard boom (LP22911)
• 150-in. (3810-mm) precision spray boom (LP22885)
• 24-ft (7.3-m) boomless spray nozzles (LP22884)

Additional features 

• Custom-engineered brackets secure to Gator cargo bed with no tools or additional straps (after initial set up)
• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gallons)

Ordering information

Contact the local John Deere dealer for availability and pricing information.

45-gal. (170.3-L) high-performance sprayer
Order number: LP39098

Shown on TH 6x4 with HP 45-gal. Sprayer

The standard Gator boom is compatible with all Gator sprayer models and is sold separately for the HP Gator sprayers. This fixed boom is conveniently sized at 43 in. (1.1 m) and does not extend wider than the Gator bed, but it is perfect for covering ground quickly and thoroughly with a 120-in. (3-m) spray swath.

The boom is ideal for basic spraying application. Three tips and check valves round out this offering (boom only, mounting brackets are provided with sprayers).

Boom Features:

• 43-in. (1.1-m) boom with three tips
• Check valves prevent siphoning and dripping
• Sold separately for:
  • HP 45-gal. Gator Bed Sprayer
  • HP 90-gal. Gator Bed Sprayer
  • HP 45-gal. Gator Bed Sprayer – XUV 550

Shown on TH 6x4 with HP 45-gal. Sprayer

Shown on TH 6x4 with HP 45-gal. Sprayer

The 150-in. (3.81-m) precision boom is compatible with the HP sprayers. This folding boom is made to cover ground quickly and thoroughly with five precision spray tips, TeeJet™ nozzle bodies and commercial grade diaphragm check valves. The outer tips offer versatility with built-in shut offs to allow an adjustable 90-in. (2.3-m), 120-in. (3-m), or 150-in. (3.8-m) spray swath.

150-in. (3.8-m) precision boom features:

• Folding spring hinge
• Breakaway design
• Five TeeJet tips and nozzle bodies
• Adjustable spray swath (90 in., 120 in., 150 in.)
• 1/2-in. industrial-grade rubber hose
• Designed to work with
  • HP 45-gal. Gator™ Bed Sprayer
  • HP 90-gal. Gator Bed Sprayer
  • HP 45-gal. Gator Bed Sprayer – XUV 550

TeeJet is a registered trademark of Spraying Systems Company.

Shown on TH 6x4 with HP 90-gal. Sprayer

HP 90-gal. Sprayer

The 24-ft (7.3-m) boomless spray nozzles are compatible with all HP sprayers. This boom is perfect for covering ground quickly and thoroughly with a 24-ft (7.3-m) spray swath. It is ideal for uneven terrain or where precision spray application is not necessary. TeeJet™ nozzle bodies and commercial grade diaphragm check valves round out this offering.

Boomless spray nozzles feature

• Three TeeJet tips and nozzle bodies
• Commercial-grade diaphragm check valves
• 1/2-in. (12.7-mm) industrial-grade rubber hose
• Designed to work with all HP sprayers :
• HP 45-gal. Gator™ Bed Sprayer
• HP 90-gal. Gator Bed Sprayer
• HP 45-gal. Gator Bed Sprayer – XUV 550

 TeeJet is a registered trademark of Spraying Systems Company.

45-gal. (170- L) Tow-Behind Sprayer

The HP 45-gal. (170-L) Tow-Behind Sprayer offers the ultimate in performance and versatility. With a 45-gal. capacity, high volume electric pump, and premium pistol grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray and deicer. It is the perfect match for the customer who wants extreme performance. 

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options; a 150 in. (3.8 m) precision folding, 120-in. (3-m) standard three tip, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).

HP features:

• 45 psi, 3.6 gpm SHURflo® diaphragm-type pump is designed for high hour applications and can be run dry without damage
• Premium pistol grip spray gun, designed for single hand mist to 35 ft (10.7 m) stream
• Front-mount hose tender for easy hose access and storage
• Glycerin filled pressure gauge
• TeeJet™ pressure regulation/recirculation valve
• Includes sprayer remote control

Additional features

• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill level indicators (in gal.)

Boom options (sold separately):

• 150-in. (3810-mm) precision spray boom
• 24-ft  (288-in.) boomless spray nozzles

SHURflo is trademark of SHURflo, LLC. TeeJet is a registered trademark of Spraying Systems Company.

45-gal. (170-L) tow-behind sprayer

The 45-gal. (170-L)  trail-type sprayer is equipped with a boom that sprays a wide, 120-in. width.

• Three nozzles for efficient broadcast spraying
• Boom folds up against the tank for storage

A 20-ft hose and handgun are provided.

• The 20-ft hose and handgun are helpful when spraying trees or other remote areas that cannot be reached with the sprayer itself
• A 14-in. wand on the handgun is standard equipment

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction.

• Low center of gravity gives excellent stability
• Equipped with a 4-position hitch
• Rear of the frame is designed so the sprayer will stand upright during storage to reduce the amount of space required

Additional features include:

• Diaphragm-type pump designed for high-hour commercial applications; it can be run dry without damage
• The spray wand is constructed of non-corrosive polypropylene material with Viton® components for remote spray jobs
• Two-wire fused wiring harness complete with quick-disconnects for convenient electrical hookup
• Large cap to easily fill up the tank
• Control valve to channel the spray to the boom or handgun
• Rugged translucent yellow tank with molded fill-level indicators (in gallons)

Specifications

Ordering information

Contact the local John Deere dealer for availability and pricing information.

45-gal. (170-L) tow-behind sprayer
Order number: LP20485

SHURflo is a U.S.-registered trademark of SHURflo, LLC. Viton is a U.S.-registered trademark of DuPont Performance Elastomers. Santoprene is a trademark of Exxon Mobil Corporation.

17AT Cart

• 17-ft ³ capacity
• 1000-lb load limit
• Copolymer polypropylene is compression molded for optimum thickness in all areas and maximum durability
• Heavy-duty, reinforced structural frame with a 25.4-mm (1-in.) diameter, one-piece axle to handle weight, speed, and bumps
• Spring-loaded dump latch for easy dumping and positive lock to prevent accidental unlocking when being towed
• Double-sealed, high-speed roller bearings to handle a 48-km/h (30-mph) maximum speed
• Heavy-duty polyethylene bed
  • Accepts dividers to separate cargo (template included)
• All-terrain knobby tires
  • Provides good flotation and traction in mud, sand, and other wet or soft areas
  • Flexes over bumps and ruts for a smoother, more controlled ride
  • Minimizes ground compaction to save turf and prevent ruts in soft ground
• Poly fenders to keep the operator, cart, and vehicle clean
• Suitable for use with most John Deere utility vehicles equipped with a 48-mm (1-7/8-in.) ball hitch, including Gator™ Utility Vehicle models TX, TX Turf, TH 6x4, TH 6x4 Diesel, all HPX 4x4 models, and all XUV models
• Quality and styling compatible with other John Deere equipment

Ordering information

Contact the local John Deere dealer for availability and pricing information.

17AT Cart

Order number: LPPCT17ATJD

OPS overhead organizer - black

Increase storage capacity on Gator™ XUV 550, XUV 550 S4, and RSX Utility Vehicles by adding the OPS overhead organizer to the OPS or rollover protective structure (ROPS) of the vehicle.

Product attributes:

• Three large cargo compartments, zippered mesh pockets, and pockets for tools and other small items keeps gear organized
• Heavy-weight polyester fabric for maximum durability and resistance to tear
• PVC coated for maximum water resistance and repellency
• One-piece design easily attaches and detaches to the OPS or ROPS with four straps - no tools required
• Compatible with the OPS rear screen, OPS soft roof, and OPS poly roof
• Compatible with Gator XUV 550, XUV 550 S4, and RSX Utility Vehicles

Ordering information

Contact the local John Deere dealer for availability and pricing information.

OPS overhead organizer - black
Order number: LP37044

Front turn signals

Rear turn signals and reverse lights

The turn signal kit includes turn signals (front and rear), reverse lights, and four-way flashers (hazards). The turn signal and hazard switch mounts on the dash of the vehicle.

Requires turn signal light harness kit.

Compatible with XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590i, XUV590i S4

NOTE: Not intended for use on public roadways.

Turn signal light harness kit

The turn signal light harness kit is required when installing the turn signal light kit.

The kit includes the switches and wire harnesses.

Compatible with Gator™ HPX, XUV560, XUV550, XUV590i, XUV590i S4, XUV625i, XUV825i, XUV825i S4, XUV855D, and XUV855D S4 Utility Vehicles.

1587.6-kg (3500-lb) winch (shown on XUV590i)

This winch also requires a winch mount kit and a 50.8-mm (2-in.) front receiver with recovery loops.

Parts in the kit:

• WARN ProVantage 1587.6-kg (3500-lb) winch
• Roller fairlead assembly
• Hook
• Hook strap
• 3-m (10-ft) hand-held remote
• Winch contactor

WARN and ProVantage are trademarks of Warn Industries, Inc.

Winch accessories kit

Double the pulling power, change the pulling direction, and keep the winch in proper working order.

The accessories kit is essential gear for operators getting the most out of their winch:

• Effectively anchors to trees/boulders
• Change the pulling direction
• Double the pulling capacity

The accessories kit includes:

• Flexible tree strap
• Snatch block
• Shackle

Each kit comes in a black Cordura® heavyweight-nylon soft case.

Cordura is a trademark of INVISTA.

Winch mount for non winch-ready vehicles

For utility vehicles not winch-ready from the factory.

Parts in the kit:

• Main winch wiring harness
• Winch disconnect harness (to glovebox)
• Harness to run from winch body to main winch wiring harness
• Positive battery cable for winch
• Winch fairlead support
• Mount hardware
• Safety labels
• Winch operator manual
• Tunnel bracket

Shown with optional attachments

The abrasion-resistant half windshield is an excellent solution for operators that want to deflect the main force of wind, but still allow airflow through the operator’s station. 

• Made with high-impact-strength abrasion-resistant polycarbonate material
• No tools required - features the operator protection system (OPS) quick-clamp mounting system. The windshield attaches to the OPS or rollover protective structure (ROPS) with two quick clamps, making attaching and removing quick and easy

Canvas rear panel

NOTE: Picture shown is canvas roof/rear panel. Canvas rear panel would be rear portion only.

Features of the canvas rear panel:

• Made from premium, heavy-duty 600 denier-solution dyed, water-resistant polyester with UV stabilizers, for mold and tear resistance
• Durable PVC window resists yellowing or cracking. Window opens easily with a zipper and can be secured in place with straps.
• Installs in minutes
• Installed with full windshield and roof will help keep dust out of operator station
• Compatible with poly roof, canvas doors, poly doors

OPS full no-scratch windshield

Installed on Gator™ XUV 550

NOTE: Windshield is not tinted; picture is tinted to show details

The OPS poly full windshield is available for Gator XUV 550, XUV 550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles when equipped with an operator protection system (OPS) or rollover protective structure (ROPS) to provide additional protection for the operator and passenger.

• Manufactured from super premium, two-sided Makrolon AR grade abrasion-resistant polycarbonate.
• Increased UV longevity – resists yellowing longer than optical grade polycarbonate
• Increased chemical resistance over traditional optical grade polycarbonate
• Almost as hard as glass with greater impact strength
• 30 times less prone to scratching than standard poly windshield
• Designed to permit unfettered access to under-hood storage areas and service points (no tools required)
• Upper panel may be infinitely positioned to allow desired amount of ventilation
• Seals against the hood, OPS, and optional OPS roof
• Features the OPS quick-clamp mounting system; attach to/detach from the OPS or ROPS with ease

Expand the comfort and enjoyment of the Gator™ Utility Vehicle with the addition of the OPS glass windshield with integrated wiper kit. This windshield offers superior visibility that is clear and distortion free.

This durable, laminated glass windshield comes equipped with a standard windshield wiper.

No matter what the condition, the occupants of the vehicle will be protected from the elements; the lower section of the windshield seals tightly against the hood of the vehicle.

Requires the OPS switch bank.

The OPS glass windshield with wiper is compatible with OPS poly roofs, poly doors, side-mounted mirrors, and front hood racks.

Reservoir bottle

Spray nozzle

Especially useful for working around properties and job sites, the windshield washer kit includes these components:

• Mounting hardware
• Spray nozzle
• Large reservoir with electric pump, harness, and hose
• Three-position backlit rocker switch: off, wiper, washer

The reservoir assembly bolts to the frame. A convenient three-position rocker switch controls the windshield wiper and washer fluid. As with all Gator™ Utility Vehicle electrical kits, the washer kit ties into the vehicle's wiring harness for quick installation.

Compatible with the following vehicles:

• All Gator model year 2011-current HPX, XUV 625i, XUV 825i, XUV825i S4, XUV 855D, XUV855D S4, and M-Gator A3 Utility Vehicles
• All Gator model year XUV550, XUV550 S4, XUV560, XUV560 S4, XUV590, XUV590 S4, and RSX Utility Vehicles

Shown on Gator™ XUV550 Utility Vehicle

The operator protection system (OPS) poly rear window is an excellent solution for operators seeking to reduce dust and air flow throughout the operator station when coupled with a half or full windshield. Made out of high-impact-strength abrasion resistant polycarbonate material, this rear window is highly durable and scratch resistant. It also attaches to and detaches from the OPS or rollover protective structure (ROPS) with ease, thanks to the quick-clamp mounting system.

Compatible with model year 2017 Gator XUV560, XUV590, and RSX Utility Vehicles.

Prior to model year 2017, this is compatible with two-passenger XUV550, XUV560, XUV590, and RSX Utility Vehicles.