X354Tracteur avec corps de 107 cm (42 po)

Les formes arrondies et fluides donnent une apparence moderne et élégante :

• Le capot stylisé est doté de grilles d’admission d’air pleine longueur efficaces, de chaque côté plutôt que sur le dessus.
  • Diminution de la température de fonctionnement du moteur
  • Réduction du niveau sonore dans le poste de conduite
• L’air chaud est évacué par la calandre, loin du conducteur.
• Le capot, dont la couleur est intégrée au matériau, est très durable.
  • Excellente résistance aux chocs
  • Résistant aux intempéries
  • À l’épreuve des bosses et de la rouille
• Une calandre distincte et un grand capot des ailes monopièce complètent l'ensemble.

Pour obtenir des performances de coupe optimales, le corps de tondeuse doit être à niveau latéralement et correctement réglé sur le plan longitudinal. Un indicateur de niveau de corps embarqué et amovible et une clé hexagonale sont fournis pour faciliter le réglage. Ils sont rangés en toute sécurité sous le siège du tracteur.

Des orifices de mise à niveau pour réglage de précision sont situés de chaque côté du poste de conduite au-dessus des boulons de rappel de niveau de la tondeuse. Combinés à l’outil hexagonal, ils fournissent un accès pratique pour un réglage facile et rapide de la tondeuse, afin d’obtenir la meilleure qualité de coupe possible.

Le réglage de précision est une caractéristique de série sur tous les tracteurs X300, X500 et sur tous ceux de la série Select™ :

• Il n’est pas nécessaire d’accéder au dessous du capot des ailes pour régler le niveau de la tondeuse.
• L’indicateur de niveau de corps embarqué, les orifices pour réglage de précision et l’outil hexagonal fonctionnent ensemble.
  • Mettez le corps à niveau le corps en sens latéral
  • Définissez le bon taux de ratissage (selon l’axe longitudinal du corps)
  • Calibrez la hauteur de coupe par rapport à la position du bouton de réglage de la hauteur de coupe
• Le système de réglage de précision simplifie la mise à niveau du corps de tondeuse si celle-ci est équipée d’un souffleur Power Flow™.
  • Pour une coupe optimale, le niveau de la tondeuse doit être réglé à chaque fois que vous posez et que vous déposez le souffleur durant les travaux de tonte. Le système de réglage de précision facilite ce réglage.

Consultez le livret d’entretien pour connaître les procédures de réglage appropriées pour chaque modèle de tracteur. Une bonne mise à niveau du corps de tondeuse comprend les étapes de réglage de base suivantes :

• Garez le tracteur sur une surface de niveau.
• Gonflez les pneus à la pression appropriée.
• Consultez l’étiquette du bouton de réglage de hauteur de coupe qui se situe sur la console de la machine. Cette étiquette montre la position de mise à niveau du corps et les points permettant de procéder au réglage du niveau.
• Tournez le bouton de réglage de la hauteur de coupe jusqu’à la position correspondant au bon réglage du niveau de corps.
  • Pour les modèles X300, utilisez la position 2,75.
  • Pour tous les autres modèles, utilisez la position 2,5.
• Réglez les roues de la tondeuse au besoin afin d’éviter qu’elles soient en contact avec le sol.
• Retirez l’indicateur de niveau de corps embarqué situé sous le siège.
• À l’aide de l’outil et des orifices de réglage de précision, réglez le niveau du corps de tondeuse latéralement jusqu’à ce que l’indicateur de niveau de corps puisse passer légèrement sous les bords inférieurs droit et gauche du corps au niveau des points de réglage désignés. L’emplacement des points de réglage varie légèrement d’un corps de tondeuse à l’autre.
  • Les points de réglage arrière gauche et droit se trouvent sous le rebord du corps près des roues arrière de la tondeuse, si celle-ci en est équipée.
• Réglez le niveau du corps de tondeuse selon l’axe longitudinal, si nécessaire.
  • Desserrez les écrous arrière de manière égale de chaque côté de la biellette de relevage avant.
  • Vissez les écrous avant uniformément de chaque côté dans le sens horaire pour relever l’avant de la tondeuse et dans le sens antihoraire pour l’abaisser, jusqu’à ce que l’indicateur puisse tout juste passer sous le point de réglage avant.
  • Resserrez les écrous arrière lorsque le réglage est terminé.
• Remettez l’indicateur en position de remisage.

REMARQUE : L’outil de réglage fourni avec le tracteur est une clé hexagonale à bille de 8 mm (numéro de pièce M162737). L’extrémité arrondie permet un certain désalignement avec le boulon pendant le réglage du corps.

Le châssis fabriqué en acier plié et soudé robuste est renforcé aux endroits critiques pour une solidité accrue :

• Il est fabriqué à partir d’un acier de calibre 12 de 2,66 mm (0,105 po) d’épaisseur pour une longue durée d’utilisation.
• Le pare-chocs avant et la plaque d’attelage de série, en acier de calibre 9 de 3,8 mm (0,15 po) d’épaisseur, complètent l’assemblage du châssis.
• La plaque d’attelage arrière peut supporter deux masses d’alourdissement Quik-Tatch de 19 kg (42 lb).
  • Le support de masse d’alourdissement intégré au châssis des modèles à deux roues directrices.
  • Les modèles à quatre roues directrices nécessitent l’installation d’un support de masse offert en option.

Le tracteur est propulsé par un groupe moteur iTorque™ de John Deere ; l’ensemble des caractéristiques du moteur et le capot de conception exclusive offrent une puissance de traction accrue, un refroidissement uniforme et une grande durabilité.

 

Les principales caractéristiques du moteur sont les suivantes :

• Une puissance de 13,8 kW (18,5 hp)
• Une grosse cylindrée de 603 cm³
• Une configuration à 2 cylindres en V avec refroidissement à l’air produisant une puissance constante, sans bruit excessif
• Parmi les caractéristiques de qualité, il y a notamment :
  • Les chemises de cylindre en fonte
  • Les soupapes en tête
  • Le graissage pressurisé
  • Le filtre à huile interchangeable
  • Le filtre à air à double effet
• Conception à 2 cylindres en V :
  • Une puissance et un rendement supérieurs
  • Des démarrages faciles
  • Un fonctionnement en douceur

Alternateur à volant-moteur

Un alternateur à volant-moteur génère suffisamment d’électricité pour recharger rapidement la batterie et alimenter les accessoires électriques, comme les phares ou un pulvérisateur :

• Capacité de 15 ampères
• Régulé afin de maintenir la pleine charge de la batterie sans la surcharger

Le corps de tondeuse Accel Deep de 107 cm (42 po) en acier embouti, caractérisé par une coque profonde et un dessus plat, offre une coupe d’excellente qualité et une productivité remarquable, en plus d’être facile à nettoyer, durable et polyvalent. Il fournit un rendement optimal et assure une excellente dispersion des brins d’herbe coupée, même à grande vitesse :

• Profondeur de 12,6 cm (4,97 po) sur l’ensemble de la coque pour un rendement optimal lors de la tonte, du hachage et de l’ensachage
  • Accessoire MulchControl™ en option pour des performances de hachage supérieures et une grande polyvalence
• Conception en acier embouti qui élimine les arêtes vives et les recoins où la matière pourrait s’accumuler et réduire le performances de tonte
• Corps de tondeuse suspendu à la machine pour une coupe uniforme et de niveau
  • Roues de tondeuse réglables situées juste au-dessus du niveau du sol, réduisant les dégâts sur le terrain

Excellente qualité de coupe

Le corps de tondeuse profond en acier embouti offre une coupe d’excellente qualité. Il offre à l’herbe coupée en suspension suffisamment d’espace pour être évacuée sans être recoupée :

• La puissance de la tondeuse sert à couper l’herbe une seule fois, ce qui améliore grandement sa capacité de coupe.
  • Cela permet de garder une excellente qualité de coupe à grande vitesse.
• Le débit d’éjection constant empêche la matière déjà coupée d’entrer en contact avec l’herbe à couper, ce qui assure une coupe nette.
• Même en mode de hachage, la coupe est plus uniforme que celle qu’offrent d’autres types de conception. En effet, la profondeur accrue du corps permet une circulation continue, une deuxième coupe optimale et une distribution uniforme des brins d’herbe coupée.

Productivité – accélère le travail

Le corps de tondeuse profond en acier embouti permet d’accroître la productivité, donc d’accélérer le travail. Il offre à l’herbe coupée en suspension suffisamment d’espace pour être évacuée rapidement du corps, réduisant la quantité d’herbe coupée deux fois, ce qui permet de concentrer la puissance de la tondeuse sur l’herbe à couper :

• Améliore grandement la capacité de la tondeuse à assurer un excellent rendement de tonte dans des conditions difficiles et à grande vitesse

La grande goulotte d’éjection, à la fois haute et large, permet de traiter un plus grand volume de matière :

• Elle assure une éjection uniforme des brins d’herbe coupée quelle que soit la vitesse de tonte
• Elle réduit les risques d’obstruction, ce qui est particulièrement important durant la tonte de gazon épais, dense ou humide ou durant l’ensachage
• La goulotte d’éjection d’herbe coupée comporte une entrée large optimisée qui facilite la récupération de la matière grâce au débit d’air en provenance de la grande ouverture du corps de la tondeuse.

Propreté – à la fois pour la tondeuse et pour le conducteur

Grâce à son dessus plat, le corps de tondeuse en acier embouti demeure propre et permet au conducteur de ne pas se salir :

• Que ce soit sur le dessus ou le dessous, le corps de tondeuse ne présente que très peu d’endroits où l’herbe coupée peut s’accumuler.
  • Le dessus du corps demeure propre, ce qui réduit le temps et les efforts nécessaires au nettoyage et à l’entretien.
  • Le dessous du corps est autonettoyant, ce qui prévient l’accumulation de matières pouvant nuire à la circulation de l’air et des brins d’herbe coupée et lui assure un rendement optimal.
  • Il n’est pas nécessaire de procéder aussi souvent au nettoyage et au retrait des matières accumulées dans la partie inférieure du corps.
• La profondeur du corps de tondeuse Accel Deep réduit la quantité de brins d’herbe coupée qui s’échappent par l’avant du corps.
  • La quantité de brins d’herbe coupée qui aboutissent sur le conducteur et sur le corps de tondeuse est négligeable.
  • Grâce au débit uniforme de matière éjectée par la goulotte et à la réduction de la quantité d’herbe coupée deux fois, les brins d’herbe coupée sont plus gros et ont moins tendance à aboutir sur le conducteur.
  • Le hachage empêche complètement l’éjection de matières et l’accessoire MulchControl fait en sorte que le hachage constitue une solution pratique dans la plupart des situations de tonte.

Le nettoyage du corps de tondeuse, sur le dessus et en dessous, est l’une des activités d’entretien les plus fréquentes :

• Le dessus plat du corps de tondeuse offre peu d’endroits où les brins d’herbe coupée peuvent s’accumuler et facilite le retrait des matières qui réussissent malgré tout à s’y accumuler.

Un orifice de nettoyage est prévu pour faciliter le nettoyage de la partie inférieure du corps de tondeuse.

• Un raccord de tuyau souple est inclus avec le corps de tondeuse.

• La poignée MulchControl se trouve sur le dessus du corps de tondeuse et sert à ouvrir ou à fermer le déflecteur d’éjection.
  • Le conducteur doit donc descendre de la machine pour activer ou désactiver le mode de hachage.
• Le passage du mode de hachage au mode d’éjection latérale ou inversement ne prend que quelques secondes.

L’accessoire MulchControl convient aux situations de tonte suivantes :

• Lorsque le conducteur procède habituellement au hachage de l’herbe, mais qu’il veut passer au mode d’éjection latérale quand l’herbe est trop longue
• Lorsque le conducteur utilise habituellement l’éjection latérale, mais qu’il souhaite pouvoir fermer la goulotte afin de contrôler la quantité de brins d’herbe coupée
• Lorsque le conducteur souhaite rester en mode de hachage sur la pelouse principale, mais qu’il a souvent recours à l’éjection latérale sur les pelouses secondaires
• Lorsque le conducteur procède à l’ensachage des brins d’herbe coupée, mais qu’il veut tondre le plus longtemps possible avant de devoir vider les sacs

En mode d’éjection latérale, l’accessoire MulchControl continue de hacher environ le tiers de l’herbe coupée. Par conséquent, il s’agit d’un mode de hachage partiel. Ce mode peut être avantageux durant l’éjection latérale de l’herbe coupée ou l’ensachage, car il réduit le volume d’herbe rejetée. Néanmoins, il présente parfois des inconvénients dans les cas suivants :

• Lorsque l’herbe est coriace, comme le gazon de Manille et l’herbe des Bermudes dans le sud des États-Unis
• Lorsque l’herbe est humide ou très longue, comme dans la région du Nord-Ouest Pacifique, aux États-Unis
• Lorsqu’un ensachage optimal et un nettoyage de la pelouse sont souhaités

 

La durabilité supérieure est intégrée à la conception.

Le corps de tondeuse 42A est doté de logements robustes pour les moyeux de lames afin de garder les lames alignées, même après des années d’utilisation intensive :

• Les nervures accroissent la robustesse de la coque.
• Le poids global du corps de tondeuse 42A est de 16 pour cent supérieur à celui du corps de tondeuse Edge™ Xtra de 107 cm (42 po).

Les roues de la tondeuse ont un double ancrage :

• Cela accroît leur robustesse et leur durabilité pour une durée d’utilisation plus longue et sans problèmes.
• Le réglage de la hauteur des roues et donc de la hauteur de coupe est facilité et accéléré grâce à l’utilisation d’un seul boulon.

La conception du système d’entraînement par courroie à basse tension réduit la charge latérale exercée sur le roulement inférieur de moteur et les roulements de corps de tondeuse, ce qui accroît la durée d’utilisation.

Le bord extérieur laminé du corps accroît sa robustesse et offre une meilleure protection.

La peinture appliquée en deux étapes par électrodépostion et par peinture en poudre fournissent une protection supplémentaire contre la rouille.

Polyvalence – il est facile de passer du mode d’éjection latérale aux modes de hachage et d’ensachage

La tondeuse 42A est conçue pour offrir une polyvalence maximale, en permettant de passer facilement d’un mode d’éjection à un autre :

• La conception d’éjection d’herbe coupée de la tondeuse permet l’ensachage en ajoutant simplement la goulotte, une fois que les lames d’ensachage spéciales ont été posées.
  • La goulotte d’éjection d’herbe coupée de la tondeuse 42A est facile à poser et est maintenue fermement en place à l’avant et à l’arrière. Elle offre ainsi un raccord étanche avec le corps de tondeuse.
    • Le dispositif de verrouillage arrière réglable permet d’optimiser le réglage pour une utilisation simple et un raccord parfaitement étanche.
  • Les lames d’ensachage conviennent aussi à l’éjection latérale.
• Avec l’accessoire MulchControl disponible en option (en plus des lames de hachage spéciales), il est possible de passer du mode d’éjection latérale au mode de hachage ou inversement en faisant simplement basculer un levier.
• Le sac récupérateur d’herbe arrière peut être utilisé avec les lames MulchControl posées.
• Le déflecteur avant, inclus avec la goulotte du sac récupérateur d’herbe arrière ou avec MulchControl (B), peut rester en place lors de l’éjection latérale.
  • Ce déflecteur peut être retiré afin d’optimiser les performances d’éjection latérale.
• L’accessoire MulchControl en option comprend un déflecteur MulchControl arrière (A) maintenu en place par deux boulons de carrosserie au niveau du bord arrière de l’ouverture d’éjection. Ce déflecteur :
  • Doit être retiré pour poser le sac récupérateur d’herbe arrière à l’aide d’une clé de 13 mm (0,51 po) (la goulotte du sac récupérateur d’herbe ne peut être posée sans retirer ce déflecteur)
  • N’a pas besoin d’être reposé pour l’éjection latérale
  • Doit être reposé pour le hachage

Option MulchControl

L’accessoire MulchControl conçu pour le corps de tondeuse 42A rend le hachage plus pratique dans de nombreuses situations de tonte. En effet, il offre non seulement d’excellentes performances en matière de hachage, mais il permet également de passer facilement au mode d’éjection latérale ou au mode d’ensachage, selon les besoins. Le hachage de l’herbe en brins d’herbe coupée offre notamment les avantages suivants :

• Il donne une pelouse magnifique.
• Il empêche la projection des brins d’herbe coupée sur le conducteur, les allées ou dans les plates-bandes.
• Il réduit la quantité d’engrais nécessaire.
• Il élimine l’effort nécessaire pour se débarrasser des brins d’herbe coupée.

Fonctionnement de l’accessoire MulchControl

L’accessoire MulchControl, de conception simple et innovante, est facile à utiliser et à entretenir :

• L’accessoire MulchControl inclut des déflecteurs permettant de réguler la circulation des brins d’herbe coupée sous le corps de tondeuse.
  • Lorsque le déflecteur MulchControl est ouvert, la plus grande partie de l’herbe coupée passe par l’ouverture d’éjection.
  • Lorsque le déflecteur MulchControl est fermé, l’herbe coupée reste sous le corps de tondeuse et est hachée et déposée sur le gazon.

Sac récupérateur d’herbe arrière de 247 l (7 boisseaux)

Un système de récupération arrière par sac d’une contenance de 247 l (7 boisseaux) est disponible en option pour la tondeuse Accel Deep de 107 cm (42 po). Ce système permet de ramasser efficacement les brins d’herbe coupée et les feuilles.

La conception moderne de la trémie offre d’excellentes performances d’ensachage, un fonctionnement plus propre et des sacs faciles à vider :

• Capacité de 247 l (7 boisseaux)
• Goulotte inférieure facile à attacher (commandée séparément)
• Conduite d’évacuation de l’air
• Verrou à ressort pratique
• Indicateur de remplissage selon le débit d’air
• Système de montage Quik-Tatch
• Haut de trémie étanche
• Sacs en tissu souple disponibles

Lames de tondeuse

Les lames d’ensachage à grande aspiration sont comprises avec la goulotte. Elles offrent des performances optimales lors de l’ensachage dans des conditions difficiles, comme lorsque l’herbe est humide, dense ou longue :

• Les lames d’ensachage à grande aspiration conviennent aussi très bien à l’éjection latérale.

Des lames de hachage sont comprises avec l’accessoire MulchControl. Elles peuvent servir au hachage, à l’éjection latérale et à l’ensachage dans la plupart des conditions.

Tableau d’utilisation des lames de tondeuse

REMARQUE : Sur l’illustration présentée ci-dessus, le trait plein représente la trajectoire d’un tracteur doté de quatre roues directrices, tandis que le trait hachuré représente la trajectoire d’un tracteur doté de deux roues directrices.

Une direction sur les quatre roues offre un net avantage quant à la maniabilité et à la capacité de taillage par rapport aux tracteurs dotés de deux roues directrices.

Par exemple, avec le tracteur Select X384 équipé d’une tondeuse Accel Deep™ de 122 cm (48 po) (les chiffres ci-dessous correspondent à ceux qui figurent sur l’illustration ci-dessus) :

1. Le rayon du cercle complet passe de 53 cm (21 po) pour un tracteur X380 à deux roues directrices à seulement 23 cm (9 po), ce qui élimine ou réduit considérablement la nécessité de reculer pour achever la tonte près des arbres, des buissons, etc.
2. Les roues du tracteur ne nuisent pas au fonctionnement de la tondeuse puisqu’elles se trouvent à plusieurs centimètres de l’obstacle autour duquel la tonte est effectuée.
3. Le rayon de braquage extérieur est plus faible, ce qui réduit le temps nécessaire pour effectuer les virages et accroît l’efficacité de la tonte.

En outre, la tonte autour des massifs de fleurs et d’autres aménagements est plus complète lorsqu’un tracteur à quatre roues directrices est utilisé.

Virages serrés

Le système de direction aux quatre roues est conçu pour les virages serrés, ce qui améliore le rendement de la tonte :

• Les angles de chasse, de carrossage et de pivot de fusée sont optimisés afin de réduire l’effort nécessaire, surtout lorsque la machine se déplace en ligne droite juste avant l’exécution d’un virage.
• La géométrie du système de direction a été conçue avec l’aide de la modélisation 3D afin de veiller à ce que les quatre roues travaillent de concert.
• Les roulements à billes étanches de l’arbre de torsion et des fusées de roue arrière permettent de réduire la friction.
• Le petit rayon de frottement, qui est de moins de 2,5 cm (1 po) à l’arrière réduit les éraflures et les secousses.

Conçu pour faciliter la direction

Les roulements à billes scellés sont utilisés aux principaux joints de direction sur les quatre roues pour un frottement réduit, une durée d’utilisation prolongée et un entretien minime.

Il est essentiel que la direction soit souple pour que la tonte soit agréable :

• Le grand volant de direction de 35,6 cm (14 po) de diamètre offre un effet de levier accru et facilite les virages.
• Le grand secteur denté offre un rapport de démultiplication de la direction amélioré (supérieur).
  • Plus le rapport de direction est élevé, moins le braquage nécessite d’effort.
• La bielle de direction double aide à équilibrer les charges auxquelles la direction est soumise et procure une direction plus précise.
• Les joints à rotule aux deux extrémités des biellettes de direction permettent de réduire l’usure et de conserver la précision de la direction.
• Les longs bras de direction procurent au système de direction un avantage mécanique supplémentaire, quel que soit le mouvement.
• L’arbre de direction pivote sur un roulement à billes étanche à son extrémité inférieure, près du pignon d’engrenage, ce qui permet de réduire l’effort de braquage et d’assurer la souplesse de la direction pendant la durée de vie du tracteur.
• Le secteur denté pivote sur un arbre plutôt que sur une bague, ce qui assure un bon engrènement et élimine les coincements.
• L’arbre du secteur denté pivote sur un roulement à billes étanche à ses deux extrémités, ce qui permet de réduire l’effort de braquage et d’assurer la souplesse de la direction pendant la durée de vie du tracteur.
• Les fusées de direction avant graissables réduisent la friction et l’usure au fil du temps.

Every owner of a John riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak™ or ZTrak™ mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

• The cart has a premium molded, high-density polyethylene box construction.
• Compression molding process allows polyethyl­ene to be the optimum thickness in all areas for superior strength and durability.
• Polyethylene body will not rust or dent; it stays looking new longer.
• 0.75-in. (2-cm) x 2-in. (5-cm) stake pockets are molded in to make the addition of side extensions easy.
• Two vertical 0.75-in. (2-cm) molded channels on each side allow easy use of dividers to separate the box into two or three compartments.
• Ribs in the box bottom add strength and prevent the shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• Pneumatic tires provide turf tread for good flotation, shock absorption, and minimal rolling resistance.

Wheels

Wheels are mounted on a solid, one-piece axle for durability.
 
Iron and Oilite® wheel bearings with grease fittings provide lubrication for long life.

The pneumatic tires offer the following:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Sloped tailgate

A sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.

Tractor hitch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

Tilt latch

An easy-to-use, spring-loaded dump latch allows tilting the box for easier unloading. A steep dump angle makes emptying the cart easier.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

7P Poly Utility Cart
Order number: LP21935

Oilite is a trademark of Beemer Precision, Incorporated.

The 8-cu-ft (0.23-m³), 300-lb (136-kg) capacity 8Y Convertible Cart can be used to haul a variety of materials including lawn debris, sand, dirt, mulch, and plants. The unique convertible hitch allows changing the cart from tow-behind mode to push mode without tools.

Key features include:

• Compatible with riding lawn tractors and garden tractors
• Durable poly construction
• All-terrain pneumatic tires
• Converts from tow cart to push cart without tools
• Large handle is provided for ease of use

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes. Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
 
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck. 

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not  exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite® bearings	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

8Y Convertible Cart
Order number: LP22755

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

The 10P Utility Cart is designed, painted, and decaled to be compatible with other John Deere equipment:

• Large 650-lb (295-kg) capacity
• 10-cu ft (283-L), heavy-duty, 0.25-in. (6.4-mm) thick poly bed
• Will not dent or rust
• 15x6 tubeless pneumatic tires with turf tread for maximum traction
• Easy, hands-free foot pedal dump release
• Steep dump angle for complete emptying

 

A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.

 

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite® bearings	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (2) 42-lb (19-kg) plastic shell wheel weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information
Please contact a local John Deere dealer for availability and pricing information.

10P Utility Cart
Order number: LPPCT10JD

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials, including firewood, lawn debris, dirt, sand, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

Welded box construction provides maximum reliability:

• Requires less setup time than the bolted construction.
• Box sides and bottom are one piece and have rounded corners and no hardware for easy cleaning.

Wheels and tires

Wheels are mounted on a solid, one-piece axle for durability.

Iron/Oilite® wheel bearings with grease fittings provide lubrication for long life.

Pneumatic tires offer:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Turf-tread tires are used on the 13 Utility Cart.

Deluxe tailgate is hinged for easy emptying and can also be quickly removed without the use of tools.

Easy hookup and tilt-dump latch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

The easy-to-use latch allows tilting the bed for easier unloading:

• Steep dump angle makes emptying easier.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

13 Utility Cart
Order number: LPHDC13JD

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential user of a high-quality, affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

 

Key features of the 17P Utility Cart:

• 1,000-lb (454-kg), 17-cu ft (0.48-m³) load capacity.
• Cart has premium molded high-density polyethylene box construction.
• Compression molding process allows polyethyl­ene to be the optimum thickness in all areas for superior strength and durability.
• Polyethylene body will not rust or dent, staying new-looking longer.
• 0.75- x 2-in. (19- x 51-mm) stake pockets are molded in to make addition of side extensions easy.
• Two vertical 0.75-in. (19-mm) molded channels on each side allow for easy use of dividers to separate the box into two or three compartments.
• Ribs in box bottom add strength and prevent a shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• 16x6.5 pneumatic tires with turf tread give good flotation, shock absorption, and minimal rolling resistance.
• Wheels are mounted on a solid one-piece axle.
• Wheels turn on iron/Oilite® bushings with grease fitting for long life.
• Spring-loaded dump latch is easy to use.

A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

 

17P Utility Cart
Order number: LPPCT17JD

Oilite is a trademark of Beemer Precision Incorporated.

The 12-V outlet kit can be installed on the tractor to provide power for various 12-V equipment.

35 W sealed-beam bulb provides additional lighting for evening operation.

Light swivels and tilts to allow positioning beam on work area.

Light is designed for mounting on rear fender by drilling a hole in the desired location.

The 40-in. (102-cm) Tractor Shovel expands the usefulness of any John Deere Select Series^TM X300 or X500 Multi-Terrain Tractor by allowing it to pick up and move material. It utilizes a high-capacity electric actuator that provides lift, lower, dump, and down force functions. No front blade is required.

The tractor shovel takes the back-breaking labor out of jobs like moving mulch, spreading gravel, ground grading, and more. It installs using the tractor's existing frame holes. After initial installation, it can be removed or installed without tools.

The innovative opening design of the tractor shovel, combined with the lift height, assures complete emptying of material. The tractor shovel can also be used for scraping and grading by locking the shovel in the raised position.

Tractor recommendations and requirements:

• Rear tractor ballast recommended for improved traction
• Tire chains recommended for moving snow
• No tractor requirements

 Key features:

• Can be used when upper part of shovel is locked in the raised position as a blade (without angling capability)
• Raised and lowered with electric actuator
• Provides down force to increase scraping effectiveness of blade
• Pick-up, transport, and empty a variety of loose material including soil, gravel, mulch, and snow
• Can be removed in 10 minutes or less

Compatibility:

• LP63767 40-in. (102-cm) Tractor Shovel is Compatible with:
• Select Series X300, X300R, X304, X310, X320, X324, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

 

Unique shovel design

The unique design of the 40-in. (102-cm) Tractor Shovel allows an operator who has a Select Series™ X300 Series (including X300R and X350R) or X500 Series Multi-Terrain Tractor to use the tractor shovel for lifting and moving material as well as for typical blade functions (without blade angling), such as blading, leveling, and scraping:

• Unique shovel design empties material completely.
• Shovel can be locked in the raised position for blading applications.

Operation

The tractor shovel is operated from the tractor seat with the use of a control rod and an electric switch.

An electric actuator provides power to raise, lower, and empty the shovel.

To raise or lower the tractor shovel, use the electric switch on the tractor shovel panel.

Depress the bottom of the switch to raise the shovel and depress the top of the switch to lower the shovel.

To open the shovel for emptying, raise it completely and then pull the control rod to the yellow area of the rod and press the upper end of the electric switch.

To close the shovel, press the lower end of the electric switch until the control rod releases to the black area of the rod.

Operation of the shovel for blading or leveling

To use the tractor shovel for blading, use the handle on the right side of the shovel to raise it and then use the locking lever to lock it in the raised position.

 Specifications

 

Length of tractor shovel	40 in. (101.6 cm)
Depth of tractor shovel	11 in. (27.9 cm)
Capacity	1.7 ft3 (48 L)
Cutting blade material	0.250-in. (6.4-mm) hardened steel
Material thickness, shovel	0.125 in. (3.2 mm)
Load capacity	150 lb (68 kg), evenly distributed
Lift height	4 in. to 6 in. (10.2 cm to 15.2 cm), depending on the tractor model
Shipping weight	110 lb (50 kg)
Warranty	One-year limited warranty on parts

Tractor compatibility and requirements

The 40-in. (102-cm) Tractor Shovel is compatible with the following tractors:

• Select Series X300, X300R, X304, X310, X320, X324, X330, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

Requirements and/or recommendations:

1. Rear ballast is recommended for best performance.
2. Tire chains are helpful and recommended when operating in snow.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tractor Shovel
Order number: LP63767

This fully automatic 1.5-amp battery charger and maintainer safely charges lawn and garden, RV, deep-cycle, and most batteries that require long storage periods. It is particularly useful during winter months when the vehicle is not being used regularly, to ensure the battery stays charged:

• Automatically determines if the battery is 6- or 12-V and adjusts accordingly
• Helps maintain battery in good condition and ensures it is fully charged
• Powers on to charge battery and powers off when fully charged
• 'Onboard' feature allows mounting next to the battery on collector, street rods, and other occasional-use vehicles
• 1.5-amp trickle charges small batteries in 2 to 12 hours
• Maintains large battery charges
• Hookup protection guards battery and charger from damage 

 

Includes a choice of battery connection methods:

• Standard color-coded clips to connect to any battery
• Cable with quick-disconnect plug and end loops that can be bolted to battery terminals and easily unplugged from charger when not in use

Transporting mulch, plants or debris is easier with the double bucket holder. Just attach the holder bracket to the rear of any Select Series™ X300, X500 Series Multi-Terrain, or X700 Ultimate™ Series Tractor. It is designed to carry up to 70 lb (32 kg) of material.

 

For use with standard 5-gal. (19-L) buckets - ordered separately. 

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket holder (double)
Order number: LPJD301

Bucket (5-gal.)

Order number: LPJD400 (2 required)

Transporting mulch, plants, or debris is easier with the double bucket holder. Just attach the holder bracket to the rear of any Select Series™ X300, X500 Series Multi-Terrain, or X700 Series Tractor. It is designed to carry up to 70 lb (32 kg) of material for transporting mulch, plants, yard waste, or for adding ballast.

For use with the included John Deere 5-gal. (19-L) buckets.

NOTE: May not fit all tractor models with a weather enclosure or cab installed.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket holder (double) with buckets
Order number: LPJD301W

This black 5-gal. (19-L) bucket perfectly complements the CargO Mount™ single and double bucket holders. It is made of sturdy black plastic.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket - 5 gal. (19-L)
Order number: LPJD400

The electric power lift kit makes winter work easier by taking the effort out of raising and lowering front blade and snow blower attachments:

• Designed for Select Series™ model X350, X354, X380, X384, and X570 Tractors with foot lift
• For use with X300 and X500 front blade and snow blower attachments

Key features include:

• Includes convenient dash-mounted control switch and all electrical components
• Heavy-duty powder-coated steel components
• Controlled down force for increased usability of front blades and snow blowers
  • Provides ability to have down pressure and set implement height during work
• 4-in. (10-cm) to 6-in. (15-cm) lift height (depending on tractor model) and controllable, limited down force
• Helpful when maneuvering near curbs and for trailer loading
• Heavy-duty electric actuator designed for high-hour usage for effortless lift and lower
• Installation with simple hand tools

NOTE: The electric power lift is separate from the tractor's lift system and cannot be used to raise the mower deck. The front implement hitch uses the same tractor frame holes as the mower front draft arms; therefore, the mower deck and the snow blower or front blade cannot be mounted on the tractor at the same time.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Electric Lift Kit, X300/X500

Order number: LP64865

John Deere Fuel-Protect gasoline stabilizer is a unique formula developed to ensure optimum performance and protection year-round: 

• Has corrosion preventers
• For lawn and garden equipment and other gasoline-powered vehicles
• Ensures quick starts in all two- and four-cycle engines
• Use in gasoline, gasoline-oil mixture, and ethanol blends
• Use to treat gas cans at each fill-up or use at every fill-up of vehicle
• Keeps fuel fresh for 12 months
• Contains a fuel injector and carburetor cleaner
• 1 oz treats 2 gal.

Always use fuel stabilizer in your gasoline.

Fuel sitting in gas tanks or gas containers for more than 30 days begins to degrade. Also, blended fuels and water in gasoline can form acids that corrode fuel-system components. Protect your investment - use John Deere fuel stabilizer with corrosion preventers and prevent hard starting, surging, lack of power, poor idle, flooding, and will not run or stay running conditions caused by poor-quality fuel. Ask your local John Deere dealer or visit JDParts.

Helpful tips:

• Add fuel stabilizer every time you purchase fuel.
• Deere gasoline-powered equipment is recommended to run on a minimum of 87 octane gasoline.
• John Deere Fuel-Protect for gasoline is safe to use in all types of gasoline, including gasoline/oil mixtures and blended fuels containing up to 10 percent ethanol.
• Use plastic fuel containers to store fuel; ask your local John Deere dealer.
• For best results, use a spill-proof gas can that automatically seals the gas can vent.
• Store fuel in a cool, dry, dark place in a sealed fuel can.
• Fill tank to the top every time the machine is put away.
  • Make sure tank is drained if stored for the winter or treated if left for prolonged periods of time.

Please refer to the operator’s manual for additional recommendations and warranty information.

Fuel related issues are not considered a warrantable condition as there is no defect in the materials or workmanship of the machine. 

For more information on fuel, visit John Deere Groundscare.

Adjustable lift assist spring kit is available to lower the effort required to operate the implement lift system:

• Kit includes spring, hardware, decal, and installation instructions.
• Kit is required for use of 48-in. (122-cm) Mower Deck or 44-in. (111.8-cm) Snow Blower on a X330, X350 or X354 Tractor shipped less deck or with a 42A or 42M Mower Deck that did not include the lift assist spring.
• BM25887 lift assist spring kit is not compatible with tractors equipped with hydraulic lift.

NOTE: Lift assist is provided as standard equipment on X380 and X384 Tractors shipped with a 48-in. (122-cm) or 54-in. (137-cm) Mower Deck.

The manual angling kit makes using the 44-in. Front Blade more efficient and enjoyable. It is compatible with the 44-in. Front Blade used on all Select Series™ X300 Tractors, including the X300R rear-discharge model, and most other John Deere tractors.

 

Key features include:

• Change blade angle from the seat of the tractor with a conveniently mounted control handle
• Utilizes a three-position spring-loaded mechanism that automatically locks into place when the blade is in the proper position
• A simple twist of the conveniently mounted control handle and an easy push or pull to change blade angle to center or 20 degrees left or right
• No more stopping and getting off the tractor to angle the blade, increasing efficiency
• Powder-coated steel components
• 2-year residential warranty

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

Manual angling kit (44-in. Front Blade)

Order number: LP33712

Seat net kit provides a convenient storage area for gloves, and other small items. It is available for open-back seats.

LG265 home maintenance kit

Home maintenance kits are a handy and convenient way for dealers to supply a customer with the maintenance-interval parts as specified in their operator's manual.

 

The LG265 home maintenance kit includes the following:

 

Quantity	Description
1	Engine oil filter
2	Engine oil quart
1	Fuel filter
1	Air filter element
1	Air filter element foam
2	Spark plug

The rear bagger chute for the 42-in. (107-cm) Accel Deep™ Mower Deck (42A) is required for use of the two-bag, 7-bu (247-L) rear bagger:

• The chute is a two-piece design to allow easy installation at the mower deck, without the rear of the chute being encumbered by the hopper.
• A convenient handle is included on the top section of the chute to make installation and removal easier.
• The top section of the chute slides into the flexible hose that is attached to the hopper and is held securely to the bottom section with an easy-to-use bungee cord.
• A fill indicator tells the operator when the bags are getting full.

The rear bagger chute attachment includes special bagging blades, a toe guard (A) with features for installing the bagger chute, and a front bagger baffle (B) to direct the material rearward into the bagger chute:

• The replacement toe guard is intended to remain on the mower deck and to be used for any mower application - bagging, side discharging, or mulching.
• A baffle to narrow the side-discharge opening (where the bagger chute is installed on the mower deck) and direct the material into the chute is provided with the rear bagger chute and needs to be bolted underneath the deck at the front.
  • This baffle may remain in place when the bagger chute is removed for side discharging material, however for ultimate side-discharge performance it could be removed.
  • This front baffle included with the bagger chute attachment is not required if the mower deck is equipped with the MulchControl™ attachment. The MulchControl front baffle can remain with the gate open for bagging and serves the same purpose.

Installing the chute is easy:

• First, slide the front mounting pin into the tube that is on the front end of the toe guard.
• Next, swing the chute toward the back and lock it in place at the rear.

The bagger chute is securely held in place at the front and rear to provide a tight seal between the mower deck and the chute.

The rear latch is adjustable to allow for the optimum setting for easy use and a tight seal.

When a mower deck is equipped with both the optional MulchControl attachment and a rear bagger

The operator's manuals provided with the rear bagger chute and the MulchControl attachment should be used as the primary guide, however these tips may be helpful to keep in mind:

• Both the rear bagger chute and the MulchControl attachment come with a baffle that bolts inside the mower deck along the front edge to narrow the discharge opening, which has been optimized for side discharging material, and direct the material into the bagger chute.
  • If the mower deck is equipped with MulchControl, the front bagger baffle included with the bagger chute is not used.
• The front baffle, either the one included with the rear bagger chute or the one included with MulchControl (B), can remain in place for side discharging.
  • For ultimate side-discharge performance this baffle can be removed.
• The optional MulchControl attachment includes a rear MulchControl baffle (A), held in by two carriage bolts, at the rear edge of the discharge opening. This baffle:
  • Must be removed for installation of the rear bagger chute, a 13-mm (0.51-in.) wrench is required (the bagger chute cannot be installed without removing this baffle)
  • Can remain removed for side discharging material
  • Must be re-installed for mulching

Mower blades

High lift bagging blades are included with the chute. They provide optimum performance when bagging in difficult conditions, such as when the grass is moist, dense, or long:

• High-lift bagging blades also work well when side discharging material.

Mulching blades are included with the MulchControl attachment. They can be used for mulching, side discharging, and bagging in most conditions.

Mower blade use chart

Mode(s) of operation	Mower blade
Side discharging mode only	M170639 side-discharge blade (shipped with mower)
Bagging mode only	GX25668 bagging blade (shipped with BG20754 rear bagger chute)
Mulching mode only	M170642 mulching blade (shipped with BM24794 MulchControl)
Side discharge and mulching	M170642 mulching blade (shipped with BM24794 MulchControl)
Side discharge and bagging	GX25668 bagging blade (shipped with BG20754 rear bagger chute)
Side discharge, mulching, and bagging	M170642 mulching blade (shipped with BM24794 MulchControl)

The 7-bu (247-L) hopper provides an efficient means of collecting grass clippings and leaves using either the cut-and-throw rear bagger or the Power Flow material collection system (MCS):

• 38-in. (97-cm) and 42-in. (107-cm) mower decks use the cut-and-throw system.
• 48-in. (122-cm) and 54-in. (137-cm) mower decks use the Power Flow system.

The hopper design provides modern styling, great bagging performance, cleaner operation, and easy-to-empty bags.

The 7-bu (247-L) MCS features:

• 7-bu (247-L) capacity
• Easy-to-attach lower chute (ordered separately)
• Handle on chute
• Air exhaust duct
• Convenient spring-latch
• Airflow fill indicator
• Quik-Tatch mounting
• Sealed hopper top
• Loose-knit bags available

A loose-knit bag is available as an option for use with 7-bu (247-L) cut-n-throw rear baggers and Power Flow™ baggers:

• Two loose-knit bags are required.
• The loose-knit bag allows more air to flow through and provide more complete bag filling in wet and heavy grass conditions.

Dump from the seat capability for X300 Series Tractors

The MCS 7 attachment is designed to provide dump from the seat grass collection/expulsion for John Deere X300 Series Tractors equipped with the 2-bag material collection system (MCS). The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.

The aluminum body is lightweight and easy to handle. Conveniently located hand lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere MCS, installation is a breeze with simple hand tools.

 

Features:

• Lightweight aluminum construction
• Designed for full material expulsion
• Easy access self-latching spring tripped handle
• Ships almost fully assembled (5 minute handle assembly)
• Installs in seconds (after initial assembly)

Benefits:

• Easy - Convenient Access to dump handle directly from seat 
• Clean - No material handling, no mess 
• Efficient - Unload and go without leaving the seat 

NOTE: Fits John Deere X300 Series 2-bag material collection systems. Not compatible with EZtrak Zero-Turn Mowers or the X300R Rear Discharge Tractor.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MCS 7 attachment
Order number: LP47168

A durable cast-iron weight can be mounted to each front wheel.

These weights are recommended for use when operating on slopes, especially when the tractor is equipped with a rear grass bagger or other rear-mounted equipment.

Each weight requires BM17978 mounting hardware.

The 42-lb (19-kg) Quik-Tatch can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.

This weight is constructed of cast iron and weighs approximately 42 lb (19 kg).

Some vehicles have built-in front and/or rear weight brackets to hang the weights on; others require a weight bracket that must be ordered separately.

X400/X500 Heavy-Duty Garden Tractors and X700 Series Tractors require the following parts when weights are installed on the front of the tractor:

• One  M147986 weight retaining rod (Parts)
• Two  M40461 spring clip (Parts)

The optional front weight bracket/bumper is available to replace the standard front bumper on the following tractors:

• Select Series™ X300, X300R, X304, X305R, X310, X320, X324, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Model year 2007 and later (SN 020001-) Select Series model X500 Tractor
• All X530 Select Series Tractors
• Model year 2011 and later (SN 060001-) Select Series model X534 Tractor
• X570 Select Series Tractor

NOTE: Weights are ordered separately.

Holds up to four 42-lb (19.1-kg) Quik-Tatch weights:

• Provides an alternative to front-wheel weights for ballasting rear-mounted equipment
• Makes the 42-in. (106.7-cm) Hydraulic Tiller compatible with the X530 Tractor
• Functions as a bumper when weights are not installed

 

Can be used in combination with all John Deere equipment, except the following:

• Styled front bumper (BM23056)
• 40-in. (101.6-cm) Tractor Shovel

Rear weight bracket is designed to hold two suitcase weights on X300 Tractors and up to four suitcase weights on X500 Multi-Terrain Tractors.

• This item required for 4-wheel-steer tractors only; weight bracket is built into frame of 2-wheel-steer tractors.
• It is particularly useful to counterbalance a front-mounted attachment such as a snow blower or blade.
• Weight bracket can be quickly mounted to the rear of the tractor.
• Weight bracket will not interfere with rear grass bagger mounting bracket.

Hardware is required for installing each front-wheel weight.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front-wheel weights are not available for special edition tractors because the styled front-wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.

StarLock™ blade design

StarLock™ blade design

StarLock™ blade design

Features and benefits

• Homeowners can now achieve results just like the professionals
• Brush is easy to adjust for varying mower cutting height
• Brush adjusts to varying ground conditions and allows the operator to freely maneuver the vehicle without damaging the turf
• The brush striping kit is a very economical and functional attachment

Compatible with the following:

• 42A - 42-in. (107-cm) Side Discharge Mower for X350, X354, and X370 Tractors

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

42A - 42-in. (107-cm) tractor grass groomer

Order number: LP63762

Leveling gauge allows quick and accurate mower deck leveling and cutting height adjustment.

Can be used for:

• Lawn tractors
• Lawn and garden tractors
• Riding mowers
• Front mowers
• Commercial walk-behind mowers
• Zero-turn-radius mowers

MulchControl advantages and benefits

MulchControl for the 42-in. (107-cm) Accel Deep (42A) Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• MulchControl includes baffles to control the flow of material under the deck.
  • When the MulchControl baffle is open, most of the material passes through the discharge opening.
  • When the MulchControl baffle is closed, the material stays within the deck and gets chopped into mulch and deposited in the turf.

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
  • The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

MulchControl limitations

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses, such as Zoysia and Bermuda
• When cutting in wet, high-growth conditions, such as those found in the Pacific Northwest United States
• When optimum bagging and lawn clean-up is desired

The brush guard adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

By removing one spring clip and pin, the brush guard may be lowered to permit opening the hood.

The front bumper adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

Features include:

• Bumper can be easily mounted to the front of the tractor.
• Bumper can remain on the tractor when the front blade or snow blower are used.

Features include:

• Wipe-clean reinforced bottom around mower deck
• Easy-on side handles makes snugging down cover a snap
• Dual reinforced air vents let air circulate and help prevent ballooning in wind
• Interior lining and integrated muffler heat shield
• Heavy-duty fabric will not shrink or stretch and is coated for maximum water resistance
• Easy-on split back for fast fitting and easy access after installation
• Handy storage pocket reverses into an attractive storage case
• Two-year warranty

Cover provides heavy-duty protection for 100 Series, LT, LX, and S240 Tractors.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

Protective cover (medium deluxe)

Order number: LP93617

Features include:

• Dual vents let air circulate and help prevent ballooning in wind
• Elastic shock cord in bottom hem for a quick, custom-like fit
• Coated fabric for maximum water protection
• One-year warranty

Cover provides all-season protection for 100 Series, S240 Sport and Select Series™ X300 Series Tractors.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

Protective cover (standard)

Order number: LP93917

Deluxe thick-cushioned seat cover provides superior protection, all-day riding comfort, and lots of storage:

• Access to lumbar adjustment controls
• Large-capacity rear-zippered cargo pocket
• Two side mesh beverage pockets
• Elastic cord in bottom hem for a custom fit
• Medium size fits seats with backrests up to 15 in. (38.1 cm)

Ordering information

Contact your local John Deere dealer for availability and pricing information.

Seat cover, deluxe medium
Order number: LP92624

Seat cover protects new seats and renews old seats:

• Cushioned seat for extra comfort
• Four convenient pockets for keeping tools and gear within reach
• Elastic cord in bottom hem for a custom fit
• Medium size fits seats with backrests up to 15 in. (381 mm)

Ordering information

Contact your local John Deere dealer for availability and pricing information.

Seat cover, standard medium
Order number: LP92324

Spark arrester is available to meet the law in the State of California requiring use of a spark arresting muffler under certain conditions.

Applies in other states and Canada when needed to comply with local ordinances or customer requests.

NOTE: This law basically requires that purchasers of certain products be given written notice that it is illegal to use such machines on forest-covered, brush-covered, or grass-covered land (except watered lawns) without a spark arrester. For further information on this law, consult No. 4442.5 of the California Public Resources Code.

Features and benefits:

• 100-psi (689-kPa) SHURflo® diaphragm-type pump is designed for high-hour commercial applications; it can be run dry without damage.
• It is easy to assemble the custom mounting brackets.
  • Brackets use the existing frame holes.
• Brass-tipped spray wand is included as standard equipment; it is constructed of noncorrosive polypropylene material with Viton® components for multi-use applications.
• Check valves in the boom tips prevent siphoning and dripping, which can cause lawn spotting.
• Control valve directs spray to either the boom or spray wand for added convenience
  and versatility.
• Electrical hookup is simple with a convenient on/off switch.
• Sprayer contains a rugged translucent-yellow tank with molded fill-level indicators (in gallons).
• It is only a 15-second no-tools mounting after assembly.

Specifications

Item number	LP22861
Tank capacity	25 gal. (95 L)
Boom	60-in. (152.4-cm) boom, 90-in. (228.6-cm) spray
Spray wand reach	30 ft (9.1 m)
Hose length	19 ft (8 m)
Shipping weight	35 lb (16 kg)
Warranty	2-year consumer warranty

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

25-gal. (95-L) Mounted Sprayer for X300 and X500 Tractors

Order number: LP22861

SHURflo is a trademark of SHURflo, LLC.

Viton is a trademark DuPont Performance Elastomers.

Sprayer comes complete with a boom that sprays 60 in. (152.4 cm) wide. It also has a 12-ft (3.7-m) hose with an adjustable handgun for spot spraying lawns, shrubs, etc.

Features include:

• This sprayer is an excellent choice for spraying small- to moderate-size lawns and shrubs.
• Handgun with adjustable spray pattern is helpful when spraying fruit trees and can be used to spray trees up to 30-ft (9.1-m) high.
• A 14-in. (35.6-cm) wand on the handgun is standard equipment to give added convenience when spraying trees.

NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).

This sprayer is especially suited for maintaining residential and small commercial properties:

• Sprayers provide an excellent way to apply liquid fertilizer.
• Herbicides and pesticides can be applied along with liquid fertilizer or separately.

Advantages of using liquid fertilizer over dry fertilizer:

• Fertilizer is more readily available to plants.
• The fertilizer need not be worked into the soil by watering or rain before it will work.
• Herbicides are more effective when applied with liquid fertilizer.

NOTE: Use these sprayers with liquid-base lawn care chemicals only. They are not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

15-gal. (57-L) Tow-Behind Sprayer

Order number: LP19478

Sprayer comes with a wider boom that sprays a 90 in. (228.6 cm) width. A 15-ft (4.6-m) hose and handgun are provided.

Features include:

• 100 psi Shurflo® diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage.
• Sprayer is designed to be a good choice for customers with larger lawns with trees to care for or for light commercial spraying.
• Handgun with adjustable spray pattern is helpful when spraying fruit trees and can be used to spray trees up to 30 ft (9.1 m) in height.
• The 14-in. (35.6-cm) wand on the handgun is included as standard equipment.

NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).

This sprayer is especially suited for maintaining residential and small commercial properties.

• Sprayers provide an excellent way to apply liquid fertilizer.
• Herbicides and pesticides can be applied along with liquid fertilizer or separately.

Advantages of using liquid fertilizer over dry fertilizer:

• Fertilizer is more readily available to plants.
• The fertilizer need not be worked into the soil by watering or rain before it will work.
• Herbicides are more effective when applied with liquid fertilizer.

NOTE: Use this sprayer with liquid-based lawn care chemicals only. It is not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

25-gal. (95-L) Tow-Behind Sprayer

Order number: LP19479

SHURflo is a trademark of SHURflo, LLC.

The mounted electric broadcast spreader for Select Series and Signature Series Tractors is ideal for medium- to large-size jobs and can be used to apply fertilizer, weed killer, sand, lime, and de-icer:

• Compatible with X300 and X500 Select Series and X700 Signature Series Tractors
  • X300 Series Tractors must be equipped with 35-lb (16-kg) front wheel weights or front weight bracket and two 42-lb (19.1-kg) Quik-Tatch weights.
  • The electric broadcast spreader is not compatible with the X300R Rear Discharge Tractor.
  • When used on X700 Series Tractors, the spreader is not compatible with the weather enclosure, cabs, rear receiver hitch, or 3-point hitch.

Key features are as follows:

• 125-lb (57-kg) capacity injection molded poly hopper
• Durable welded, powder-coat frame
• Ice-melt capability
• Gear motor with 5-to-1 reducer
• Stainless-steel shutoff plates
• Directional control
• Hopper cover is standard equipment
• Available option: Barrier shield, 125-lb (57-kg) spreader

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Select Series Electric Spreader

Item number: LP35439

The barrier shield is used to direct product downward (36-in. [914-mm] width), converting the rotary spreader into a drop spreader. Perfect for ice melt and salt spreading, or for targeting specific areas.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

125-lb electric broadcast spreader barrier shield
Order number: LP23117

 

John Deere spin spreaders have features and a choice of sizes to satisfy many operators. They are a popular attachment for both homeowner and commercial operators who use them for even distribution of a variety of materials:

• Seed
• Fertilizer
• Insecticide
• Salt

All spreaders have rust-resistant stainless-steel or polyethylene hoppers as well as many stainless-steel components to ensure lasting appearance and long, trouble-free operation.

Features include:

• Positive on/off system (no cables)
• 125-lb (57-kg) capacity corrosion-resistant polyurethane hopper
• 13-in. (33-cm) pneumatic tires for easy rolling
• Enclosed gearbox (metal gears)
• Ergonomic dual handle featuring Accu-way™
• Accu-way even spread pattern adjustment
• Includes screen and cover

Accu-way is a trademark of Spyker Spreaders, Inc.

Hopper screen and throat opening

Hopper screens keep out debris and serve as chunk graters.

A stainless-steel hopper bottom plate/throat opening resists rust and corrosion, which extends the life of the spreader.

Spinner

Spinners are made of high-impact plastic that will not crack or break.

Dial-A-Matic rate control

The Dial-A-Matic rate control lets the operator fine-tune the rate application:

• Dial position locks and unlocks automatically.
• More than 80 settings provide an accurate application of materials.

Specifications

 

	125-lb (57-kg) Pull-Type Spreader	175-lb (79-kg) Pull-Type Spreader
Recommended market	Homeowner	Homeowner
Type	Tow-behind	Tow-behind
Bundle number	LP25353
Box capacity	125 lb (57 kg), 2.5 cu ft (0.07 m3)	175 lb (79 kg), 3.5 cu ft (0.1 m3)
Hopper size, in. (cm)	14.5x25.25x19.75 (36.8x64.1x50.2)	18.5x27.5x21.5 (47x69.9x54.6)
No-rust versatility
Hopper	Polyethylene	Polyethylene
Hopper screen	Aluminum	Aluminum
Hopper bottom plate	Stainless steel	Stainless steel
Throat opening, in. (cm)	0.81x2.75 (2.1x7)	0.81x2.75 (2.1x7)
Connecting hardware	Stainless steel	Stainless steel
Accurate application
Rate control	80-setting Dial-A-Matic knob	80-setting Dial-A-Matic knob
Rate gate	No-stick nylon	No-stick nylon
Rate gate linkage	Stainless steel	Stainless steel
Even dispersal
Spinner, in. (cm)	12 (366)	12 (366)
Spread pattern, ft (m)	10 to 12 (3.1 to 3.7) wide	10 to 12 (3.1 to 3.7) wide
Spread pattern equalizer	Accu-way™	Accu-way
Spinner shaft	Zinc-plated steel	Zinc-plated steel
Rotary agitator	Stainless steel	Stainless steel
Miscellaneous
Frame	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm) 1.13-in. (2.86-cm) tubular steel	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm), 1.25-in. (3.2-cm) tubular steel
Frame width, in. (cm)	18 (45.7)	18 (45.7)
Drive gears	Heavy-duty die-cast metal	Heavy-duty die-cast metal
Axle	0.63-in. (15.9-cm) solid steel, zinc plated	0.63-in. (15.9-cm) solid steel, zinc plated
Wheels/tires	13-in. x 5-in. (33-cm x 13-cm) pneumatic	13-in. x 5-in. (33-cm x 13-cm) pneumatic
Recommended travel speed	3.5 mph (5.6 km/h)	3.5 mph (5.6 km/h)
Warranty	One-year limited	One-year limited
Net weight, lb (kg)	29 (13.2)	34 (15.4)

 

Accu-way is a trademark of Spyker Spreaders, Inc.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

125-lb Pull-Type Spin Spreader

Order number: LP25353

John Deere spin spreaders have features and a choice of sizes to satisfy many operators. They are a popular attachment for both homeowner and commercial operators who use them for even distribution of a variety of materials:

• Seed
• Fertilizer
• Insecticide
• Salt

All spreaders have rust-resistant stainless-steel or polyethylene hoppers as well as many stainless-steel components to ensure lasting appearance and long, trouble-free operation.

Features include:

• Positive on/off system (no cables)
• 175-lb (79.4-kg) capacity corrosion-resistant polyurethane hopper
• 13-in. (33-cm) pneumatic tires for easy rolling
• Fully enclosed gear box with metal gears for long life
• Accu-way even spread pattern adjustment
• Includes screen and cover

 

Hopper screen and throat opening

Hopper screens keep out debris and serve as chunk graters.

A stainless-steel hopper bottom plate/throat opening resists rust and corrosion, which extends the life of the spreader.

Spinner

Spinners are made of high-impact plastic that will not crack or break.

Dial-A-Matic rate control

The Dial-A-Matic rate control lets the operator fine-tune the rate application:

• Dial position locks and unlocks automatically.
• More than 80 settings provide an accurate application of materials.

Specifications

 

	125-lb (57-kg) Pull-Type Spreader	175-lb (79-kg) Pull-Type Spreader
Recommended market	Homeowner	Homeowner
Type	Tow-behind	Tow-behind
Bundle number	LP25353
Box capacity	125 lb (57 kg), 2.5 cu ft (0.07 m3)	175 lb (79 kg), 3.5 cu ft (0.1 m3)
Hopper size, in. (cm)	14.5x25.25x19.75 (36.8x64.1x50.2)	18.5x27.5x21.5 (47x69.9x54.6)
No-rust versatility
Hopper	Polyethylene	Polyethylene
Hopper screen	Aluminum	Aluminum
Hopper bottom plate	Stainless steel	Stainless steel
Throat opening, in. (cm)	0.81x2.75 (2.1x7)	0.81x2.75 (2.1x7)
Connecting hardware	Stainless steel	Stainless steel
Accurate application
Rate control	80-setting Dial-A-Matic knob	80-setting Dial-A-Matic knob
Rate gate	No-stick nylon	No-stick nylon
Rate gate linkage	Stainless steel	Stainless steel
Even dispersal
Spinner, in. (cm)	12 (366)	12 (366)
Spread pattern, ft (m)	10 to 12 (3.1 to 3.7) wide	10 to 12 (3.1 to 3.7) wide
Spread pattern equalizer	Accu-way™	Accu-way
Spinner shaft	Zinc-plated steel	Zinc-plated steel
Rotary agitator	Stainless steel	Stainless steel
Miscellaneous
Frame	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm) 1.13-in. (2.86-cm) tubular steel	Powder-coated gloss enamel, 16 ga, 0.6 in. (1.5 mm), 1.25-in. (3.2-cm) tubular steel
Frame width, in. (cm)	18 (45.7)	18 (45.7)
Drive gears	Heavy-duty die-cast metal	Heavy-duty die-cast metal
Axle	0.63-in. (15.9-cm) solid steel, zinc plated	0.63-in. (15.9-cm) solid steel, zinc plated
Wheels/tires	13-in. x 5-in. (33-cm x 13-cm) pneumatic	13-in. x 5-in. (33-cm x 13-cm) pneumatic
Recommended travel speed	3.5 mph (5.6 km/h)	3.5 mph (5.6 km/h)
Warranty	One-year limited	One-year limited
Net weight, lb (kg)	29 (13.2)	34 (15.4)

Accu-way is a trademark of Spyker Spreaders, Inc.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

175-lb Pull-Type Spin Spreader
Order number: LP25354

The 40-in. (102-cm) Aerator Spreader can do two jobs at once. It perforates the soil while the calibrated drop-spreader follows with seed, lime, or fertilizer. It can also be used to just aerate the lawn:

• 40-in. (102-cm) width, with up to 2 in. (5.1 cm) of penetration
• 132 steel-tine tips on 8-in. (20-cm) diameter tine stars
• Three-position, full-sized lift lever
• Direct spreader drive for consistent performance
• Adjustable flow control
• 100-lb (45-kg) spreader capacity
• 4.10/3.5-4 pneumatic tires for easy pulling
• 75-lb (34-kg) capacity weight tray

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications 

Width	40 in. (101.6 cm)
Aerator depth	Up to 2 in. (5.1 cm), two positions
Spreader capacity	100 lb (45 kg)
Tines
Number of tips	132
Diameter	8 in. (20.3 cm)
Material	Steel
Lift adjuster	Manual
Wheels	4.10/3.5-4, pneumatic
Drive	Direct
Weight-tray capacity	100 lb (45 kg)

Vehicle compatibility and requirements

Requirements and/or recommendations: tow-behind equipment

1. Rear wheel weights are recommended for additional traction.
2. The 48-in. (122-cm) Tow-Behind Plug Aerator is not recommended for Select Series™ X300s, D100, LA100, 100, or L100 Series, 100 Series, LT, LTR, LX Lawn Tractors, EZtrak™ Mower or Residential ZTrak™ Mower.
3. The loaded weight of the utility cart not to exceed the weight of the vehicle and operator.
   The loaded weight of any attachment towed by an EZtrak or Residential ZTrak not to exceed 250 lb (113 kg).
4. For EZtraks and Residential ZTraks, only the 7P Utility Cart, 10P Utility Cart, or 42-in. (107-cm) Lawn Sweeper are recommended for towing.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Aerator Spreader

Order number: LPAS40JD

Broadcasts fertilizer, weed control, grass seed or ice melter products while towing behind a riding lawn tractor. 130-lb (59-kg) polyethylene hopper resists rust and is easier to clean. Spread pattern will go up to 12 ft (31 cm) depending on speed and material. New direct rod control with easy to reach handle opens and closes the material gate. Heat treated steel gears with plastic enclosure are protected from corrosive material. Large knobby tread tires roll easily over turf.

 

Two-year warranty.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

130-lb Pull-Type Spin Spreader
Order number: LP39087

This 175-lb (79-kg) pull-type broadcast spreader is designed for homeowner use:

• The polyethylene hopper will not dent or rust.
• All stainless-steel interior hardware, shaft, and agitator help to prevent corrosion.
• Large pneumatic turf tires ensure a positive drive and smooth operation.
• High-speed, 6:1 reduction glass-filled nylon gears provide the widest spread pattern at the slowest speeds.
• Fully enclosed gearbox eliminates downtime and maintenance.
• Autoflow feature stops the flow of materials - automatically - to prevent burns.
• Directional spread-pattern control feature provides positive shutoff along sidewalks and driveways.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

175-lb (79-kg) Broadcast Spreader

Order number: LPBS36JD

The sturdy sun shade provides an effective way to keep the sun off of the operator for more comfortable warm-weather operation of the tractor:

• Frame is made of strong 1.25-in. (32-mm) diameter steel tube with 0.063-in. (1.6-mm) wall thickness.

• The sun shade mounts to the heavy-duty CargO Mount™ system.

  • Sun shade includes the 4-wheel-steer rear weight bracket to provide a sturdy
    Quik-Tatch mounting system.
    • Holds up to two 42-lb (19-kg) Quik-Tatch weights on X300 Series Tractors
    • Holds up to four 42-lb (19-kg) Quik-Tatch weights on X500 Multi-Terrain Tractors
• Cloth top measures 32-in. (81.3-cm) long by 34-in. (86.4-cm) wide.
• Rear panel is made of cloth mesh material to provide additional protection from the sun while permitting the operator to see through it.
• Two bolts with hand knobs on the mounting posts allow easy removal of the sun shade.
• Elastic strap with clip is included to hold the 7-bu (247-L) hopper top open when the hopper is installed.
• Overall height to the top of the sun shade is 72 in. (182.9 cm).

 

The sun shade is compatible with the following:

• Select Series™ X300, X304, X320, X324, X340, X350, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

The 7-bu (247-L) 2-bag hopper or 14-bu (493-L) 3-bag hopper can be installed and used with the sun shade installed. The sun shade installation instructions explain how to install the hoppers with the sun shade.

Ordering Information

Please contact your local John Deere dealer for availability and pricing information.

 

X300/X500 Sun Shade

Order number: BM23054

The thatcher, used on a regular basis, reduces excessive thatch buildup that can be damaging to a lawn's health.
 
Since it provides more gentle, less aggressive action than a power rake, it can be used as a preventive maintenance tool each time the lawn is mowed.

Ordering information

 

Please contact a local John Deere dealer for availability and pricing information.

38-in. (97-cm) Front Thatcher

Order number: LP48004

An 8-in. (20-cm) extension is available to provide widths of 46 in. (117 cm) and 54 in. (137 cm) (Add an extension to one end of front thatcher to make it 46-in. [117-cm] wide; add an extension to both ends for a 56-in. [142-cm] width.)

A thatcher mounting frame is required to install the 38-in. (97-cm) front-mounted thatcher on a vehicle.

The 40-in. (102-cm) Thatcherator can be used as a dethatcher or an aerator. It can also be used to prepare an area for seed:

• 40-in. (102-cm) width to cover ground fast
• 20 spring-loaded tines for maximum performance
• Three-position adjustment
• Weight tray to allow increased scratching power

An 8-in. (20-cm) extension is available to provide widths of 48 in. (122 cm) and 56 in. (142 cm) (Add an extension to one end of Thatcherator to make it 48-in. (122-cm) wide and an extension to both ends for a 56-in. (142-cm) width.)

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	40 in. (101.6 cm)
Tines
Number	20, spring-loaded tips
Diameter	0.19 in. (0.5 cm)
Material	Steel
Weight tray capacity	100 lb (45 kg)
Lift adjuster	Three positions
Wheel
Size	8 in. (20.3 cm)
Tread	Rib
Material	Steel
Optional extension	8 in. (20.3 cm)

Requirements and/or recommendations: tow-behind equipment

1. Rear wheel weights are recommended for additional traction.
2. The 48-in. (122-cm) Tow-Behind Plug Aerator is not recommended for Select Series™ X300s, D100, LA100, 100, or L100 Series, 100 Series, LT, LTR, LX Lawn Tractors, EZtrak™ Mower, or Residential ZTrak™ Mower.
3. The loaded weight of the utility cart not to exceed the weight of the vehicle and operator. The loaded weight of any attachment towed by an EZtrak or Residential ZTrak Mower not to exceed 250 lb (113 kg).
4. For EZtraks and Residential ZTraks, only the 7P Utility Cart, 10P Utility Cart, or 42-in. (107-cm) Lawn Sweeper are recommended for towing.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Thatcherator

Order number: LPTA40JD

Chains are recommended for extra traction when using attachments such as a snow blower or front blade.

One pair of chains is included in each bundle.

TY15959 tire chains - 20x8-8
NOTE: For LA105, LA115, LA125, D100, D105, D110, D120, and D125 Tractors.

TY16200 tire chains - 20x10-8, 20x10-10
NOTE: For LA135 SE, LA145, LA155, D130, D140, D150, D155, S240, X300/less deck, X300/38X, X300/42M, X300/42X, X300/48X, X300R, X304, and X324 Tractors.
NOTE: 20x10-8 tires and 20x10-10 tires use the same chains as the height and width are the same. The rim diameter is larger for four-wheel steer tires, but does not affect chain requirements.

TY25229 tire chains - 22x9.5-12
NOTE: For LA165, LA175, D160, and D170 Tractors.

TY24327 tire chains - 22x11-10
NOTE: For X320, X340, and X360 Tractors.

TY15956 tire chains - 23x10.5-12
NOTE: For 190C Tractor.

TY26227 tire chains - 23x9.5-12, 24x9.5-12
NOTE: For X534 Tractor.

TY24328 tire chains - 24x12-12
NOTE: For X500, X520, X530, X540, and X590 Tractors. Also use with 26x10.5-12 tires on model year 2016- (SN 040,000-) X734 and X754.

TY25326 tire chains - 26x10.5-12
NOTE: For model year -2015 (SN -040,000). For X724, X734, X744, and X754 Tractors. Fits turf, bar, and heavy-duty all-purpose (HDAP) tire treads.

TY15958 tire chains - 26x12-12
NOTE: For X700, X710, X720, X730, X728, X738, X729, X739, X740, X750, X748, X758, and X749 Tractors. Will fit turf, bar, and HDAP tire treads. X729, X739, and X749 require BM22725 wheel spacer kit to provide clearance when installing tire chains.

The 42-in. (107-cm) Lawn Sweeper offers great performance and hauls an incredible 17 bu (599 L) of material. Its design gives superior brush-to-ground contact to prevent skipping and provide maximum performance for a clean path the first time through.

Features include:

• 42-in. (107-cm) clearing width
• 17-bu (599-L) capacity to make fast work of picking up material
• Convenient brush-height adjuster has eight positions for easy selection of the optimum sweeping height
• Hitch has seven positions to match up correctly with a variety of vehicles
• Large 12-in. (305-mm) x 3-in. (76-mm) wheels with bar tread have good gripping action to ensure positive brush rotation
• A unique storage feature allows the sweeper to collapse and be stored vertically to minimize storage space

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Brush height	Sweeping conditions
Ground level to 1 in. (25 mm) above	Smooth surfaces - driveways, parking lots, and sidewalks
1 in. (25 mm) to 2 in. (50 mm)	Mowed lawns under normal conditions, or light leaves
2 in. (50 mm) to 3 in. (75 mm)	High grass, heavy leaves, or heavy grass clippings

 

 

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

42-in. (107-cm) Tow-Behind Lawn Sweeper
Order number: LPSTS42JD

This John Deere dethatcher kit has two rows of individually flexing tines that gently but effectively remove grass clippings, leaves, and other lawn debris from your lawn. The kit easily attaches to the front of John Deere's 42-in. (107-cm) Lawn Sweeper (LPSTS42JD) to add thatch pickup to the sweeper's cleaning abilities. The dethatcher does not need to be removed to resume regular sweeping use.

 

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

Dethatcher kit for sweeper

Order number: LP42108

The Multi Tool includes one platform and two separate attachments, saving space and money.

 

• Includes 40-in. (101.6-cm) weight tray - capable of holding up to 100 lb (45.4 kg) of weight
• Includes pre-assembled core aerator - reduces soil compaction allowing air, water, and fertilizer to the grass roots
• Includes dethatcher - removes unwanted debris from the top of the soil to allow nutrients to reach the grass roots
• Elongated handle - makes it easier to raise into transport or lower for use
• Spring assisted lever - makes changing the attachments quick and easy

John Deere has combined the best lawn tools into one package.

Two-year warranty.

 

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

Multi Tool

Order number: LP39089

The Lawn Roller packs down sod, seed, and mole ridges. Its tough polyethylene drum does not dent or rust. The drum's rounded ends do not gouge the lawn or make ruts:

• 36-in. (91-cm) wide polyethylene drum
• 390-lb (177-kg) weight for excellent leveling
• Rounded end caps to reduce gouging
• 42-U.S. gal. (159-L) capacity
• Long-lasting Nylatron® bearings

Nylatron is a trademark of QUADRANT AG or its affiliates or licensors.

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	36 in. (91 cm)
Roller
Size	36 in. x 18 in. (91 cm x 46 cm)
Capacity	42 U.S. gal. (159 L)
Weight (filled)	390 lb (176.4 kg)
Drum/end-cap material	High-density polyethylene (HDPE)
Bearings	Nylatron

 

Requirements and/or recommendations: tow-behind equipment

1. Rear wheel weights are recommended for additional traction.
2. The 48-in. (122-cm) Tow-Behind Plug Aerator is not recommended for Select Series™ X300s, D100, LA100, 100, or L100 Series, 100 Series, LT, LTR, LX Lawn Tractors, EZtrak™ Mower or Residential ZTrak™ Mower.
3. The loaded weight of the utility cart not to exceed the weight of the vehicle and operator. The loaded weight of any attachment towed by an EZtrak or Residential ZTrak not to exceed 250 lb (113 kg).
4. For EZtraks and Residential ZTraks, only the 7P Utility Cart, 10P Utility Cart, or 42-in. (107-cm) Lawn Sweeper are recommended for towing.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

36-in. (91-cm) Tow-Behind Lawn Roller

Order number: LPPRT36JD

The 40-in. (102-cm) Plug Aerator removes plugs of soil up to 3-in. (7.6-cm) deep to allow penetration of air, water, and nutrients. It also helps relieve soil compaction:

• 40-in. (102-cm) width with up to 3 in. (7.6 cm) of penetration
• Three-position lift handle for 2-in. (5-cm) or 3-in. (7.6-cm) plug lengths
• 28 carbonized, 16-gauge, 0.06-in. (1.5-mm) steel, individually serviceable plugging tines
• 1-in. (2.5-cm) diameter high-carbon steel-tine shaft
• 4.10/3.50-4 pneumatic tires for easy pulling
• 175-lb (79-kg) capacity weight tray

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	40 in. (101.6 cm)
Aerator depth	Up to 3 in. (7.6 cm)
Tines
Number of tips	28
Spacing	6 in. (15.2 cm) apart
Material	Carbonized, 16-gauge, 0.6-in. (1.5-mm) steel
Lift adjuster	Manual, three position
Wheels	4.10/3.5-4, pneumatic
Weight-tray capacity	175 lb (79.4 kg)

Vehicle compatibility and requirements

Requirements and/or recommendations: tow-behind equipment

1. Rear wheel weights are recommended for additional traction.
2. The 48-in. (122-cm) Tow-Behind Plug Aerator is not recommended for Select Series™ X300s, D100, LA100, 100, or L100 Series, 100 Series, LT, LTR, LX Lawn Tractors, EZtrak™ Mowers, or Residential ZTrak™ Mowers.
3. The loaded weight of the utility cart not to exceed the weight of the vehicle and operator.
   The loaded weight of any attachment towed by an EZtrak or Residential ZTrak not to exceed 250 lb (113 kg).
4. For EZtraks and Residential ZTraks, only the 7P Utility Cart, 10P Utility Cart, or 42-in. (107-cm) Lawn Sweeper are recommended for towing.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Plug Aerator

Order number: LPPA40JD

The 40-in. (102-cm) Spiker Aerator penetrates soil, allowing air, water, and nutrients to enter the lawn. It also relieves soil compaction:

• 40-in. (102-cm) width with up to 2 in. (5 cm) of penetration
• 10-in. (25-cm) diameter steel-tine stars
• 132 steel-tine tips on 11 spike wheels
• 3.5-in. (9-cm) spike-wheel spacing
• Full-sized lift lever
• 4.10/3.5-4 pneumatic tires for easy pulling
• 100-lb (45-kg) capacity weight tray 40-in. (102-cm) width with up to 3 in. (7.6 cm) of penetration

Quality design

John Deere tow-behind lawn care tools are compatible with all John Deere lawn and garden tractors, as well as competitive tractors.

This implement features legendary John Deere performance and quality.

Specifications

 

Width	40 in. (101.6 cm)
Aerator depth	Up to 2 in. (5.1 cm)
Tines
Number of tips	132
Diameter	10 in. (25.4 cm)
Spacing	3.5 in. (8.9 cm) apart
Material	Steel
Lift adjuster	Manual
Wheels	4.10/3.5-4, pneumatic
Weight tray capacity	100 lb (45 kg)

Requirements and/or recommendations: tow-behind equipment

1. Rear wheel weights are recommended for additional traction.
2. The 48-in. (122-cm) Tow-Behind Plug Aerator is not recommended for Select Series™ X300s, D100, LA100, 100, or L100 Series, 100 Series, LT, LTR, LX Lawn Tractors, EZtrak™ Mower, or Residential ZTrak™ Mower.
3. The loaded weight of the utility cart not to exceed the weight of the vehicle and operator. The loaded weight of any attachment towed by an EZtrak or Residential ZTrak not to exceed 250 lb (113 kg).
4. For EZtraks and Residential ZTraks, only the 7P Utility Cart, 10P Utility Cart, or 42-in. (107-cm) Lawn Sweeper are recommended for towing.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tow-Behind Spiker Aerator

Order number: LPSAT40JD

The roomy steel-frame cab shields the operator against snow, rain, sun, and wind.
Key features include:

• Easy entry with hinged-door access
• Double-zippered access hole for control maneuverability
• Super-clear vinyl windows that are cold-crack tested to -4°F (-20°C)
• Zippered windows that allow for additional airflow
• Assembles and installs with standard hand tools in one hour
• Overall height from ground to top of cab of 78 in. (198 cm)

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

Weather enclosure

• Discontinued - LP36740 Weather Enclosure - Select Series™ X300, X304, X310, X320, X324, X340, and X360 Tractors
• LP55438 Weather Enclosure - Select Series™ X300, X304, X310, X320, X324, X340, X350, X360, X354, X370, X380, X384, X390, and X394 Tractors
• Discontinued - LP36741 Weather Enclosure - Select Series X500, X520, X530, X534, X540, and X590 (model year 2015) Multi-Terrain Tractors
• LP55439 Weather Enclosure - Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors