X584Tracteur avec corps de 122 ou 137 cm (48 ou 54 po)

Direction aux quatre roues

REMARQUE : Sur l’illustration présentée ci-dessus, le trait plein représente la trajectoire d’un tracteur doté de quatre roues directrices, tandis que le trait hachuré représente la trajectoire d’un tracteur doté de deux roues directrices.

La direction aux quatre roues offre un net avantage quant à la maniabilité et à la capacité de tonte par rapport aux tracteurs dotés de deux roues directrices (les numéros suivants correspondent au schéma affiché ci-dessus) :

1. Le diamètre du cercle non coupé est beaucoup plus petit, ce qui élimine ou réduit considérablement la nécessité de reculer pour tondre autour des arbres, des buissons, etc.

• Les braquages pour tondre autour des massifs de fleurs et d’autres aménagements sont plus efficaces avec un tracteur à quatre roues directrices.

2. Les roues du tracteur ne nuisent pas au fonctionnement de la tondeuse puisqu’elles se trouvent à plusieurs centimètres de l’obstacle autour duquel se fait la tonte.

• Les coins à angle droit des superficies rectangulaires peuvent être coupés de manière plus efficace.

3. Le rayon de braquage extérieur est plus faible, ce qui réduit le temps nécessaire pour les braquages et accroît l’efficacité de la tonte.

Servodirection hydraulique

La servodirection hydraulique est un équipement de série qui sert à optimiser les avantages des quatre roues motrices pour faire des braquages serrés et faciliter la direction :

• procure une direction souple comme celle dont bénéficient les automobilistes ;
• réduit la fatigue du conducteur et accroît sa productivité ;
• procure un rayon de braquage serré qui optimise la maniabilité ;
• simplifie et améliore la tonte autour des objets.

Virages serrés

Le système de direction aux quatre roues est conçu pour les virages serrés, ce qui améliore le rendement de la tonte :

• les angles de chasse, de carrossage et de pivot de fusée sont optimisés afin de réduire l’effort nécessaire, surtout lorsque le tracteur se déplace en ligne droite juste avant un virage.
• La géométrie du système de direction a été conçue avec l’aide de la modélisation 3D afin de veiller à ce que les quatre roues travaillent de concert.
• Les roulements à billes étanches des fusées de roue arrière réduisent la friction.
• Le petit rayon de frottement, qui est de moins de 2,54 cm (1 po) à l’arrière réduit les éraflures et les secousses.

Pour obtenir des performances de coupe optimales, le corps de tondeuse doit être à niveau latéralement et correctement réglé sur le plan longitudinal. Un indicateur de niveau de corps embarqué et amovible et une clé hexagonale sont fournis pour faciliter le réglage. Ils sont rangés en toute sécurité sous le siège du tracteur.

Des orifices de mise à niveau pour réglage de précision sont situés de chaque côté du poste de conduite au-dessus des boulons de rappel de niveau de la tondeuse. Combinés à l’outil hexagonal, ils fournissent un accès pratique pour un réglage facile et rapide de la tondeuse, afin d’obtenir la meilleure qualité de coupe possible.

Le réglage de précision est une caractéristique de série sur tous les tracteurs X300, X500 et sur tous ceux de la série Select™ :

• Il n’est pas nécessaire d’accéder au dessous du capot des ailes pour régler le niveau de la tondeuse.
• L’indicateur de niveau de corps embarqué, les orifices pour réglage de précision et l’outil hexagonal fonctionnent ensemble.
  • Mettez le corps à niveau le corps en sens latéral
  • Définissez le bon taux de ratissage (selon l’axe longitudinal du corps)
  • Calibrez la hauteur de coupe par rapport à la position du bouton de réglage de la hauteur de coupe
• Le système de réglage de précision simplifie la mise à niveau du corps de tondeuse si celle-ci est équipée d’un souffleur Power Flow™.
  • Pour une coupe optimale, le niveau de la tondeuse doit être réglé à chaque fois que vous posez et que vous déposez le souffleur durant les travaux de tonte. Le système de réglage de précision facilite ce réglage.

Consultez le livret d’entretien pour connaître les procédures de réglage appropriées pour chaque modèle de tracteur. Une bonne mise à niveau du corps de tondeuse comprend les étapes de réglage de base suivantes :

• Garez le tracteur sur une surface de niveau.
• Gonflez les pneus à la pression appropriée.
• Consultez l’étiquette du bouton de réglage de hauteur de coupe qui se situe sur la console de la machine. Cette étiquette montre la position de mise à niveau du corps et les points permettant de procéder au réglage du niveau.
• Tournez le bouton de réglage de la hauteur de coupe jusqu’à la position correspondant au bon réglage du niveau de corps.
  • Pour les modèles X300, utilisez la position 2,75.
  • Pour tous les autres modèles, utilisez la position 2,5.
• Réglez les roues de la tondeuse au besoin afin d’éviter qu’elles soient en contact avec le sol.
• Retirez l’indicateur de niveau de corps embarqué situé sous le siège.
• À l’aide de l’outil et des orifices de réglage de précision, réglez le niveau du corps de tondeuse latéralement jusqu’à ce que l’indicateur de niveau de corps puisse passer légèrement sous les bords inférieurs droit et gauche du corps au niveau des points de réglage désignés. L’emplacement des points de réglage varie légèrement d’un corps de tondeuse à l’autre.
  • Les points de réglage arrière gauche et droit se trouvent sous le rebord du corps près des roues arrière de la tondeuse, si celle-ci en est équipée.
• Réglez le niveau du corps de tondeuse selon l’axe longitudinal, si nécessaire.
  • Desserrez les écrous arrière de manière égale de chaque côté de la biellette de relevage avant.
  • Vissez les écrous avant uniformément de chaque côté dans le sens horaire pour relever l’avant de la tondeuse et dans le sens antihoraire pour l’abaisser, jusqu’à ce que l’indicateur puisse tout juste passer sous le point de réglage avant.
  • Resserrez les écrous arrière lorsque le réglage est terminé.
• Remettez l’indicateur en position de remisage.

REMARQUE : L’outil de réglage fourni avec le tracteur est une clé hexagonale à bille de 8 mm (numéro de pièce M162737). L’extrémité arrondie permet un certain désalignement avec le boulon pendant le réglage du corps.

Les formes arrondies et fluides donnent une apparence moderne et élégante :

• le capot stylisé est doté de volets d’admission d’air pleine longueur efficaces, de chaque côté.
  • Refroidissement du moteur plus efficace
  • Réduction du bruit au poste de conduite
• L’air chaud est évacué par la calandre avant, loin du conducteur.
• Le capot en résine Xenoy®, dont la couleur est intégrée au matériau, est très durable.
  • Excellente résistance aux chocs
  • Cache les éraflures
  • À l’épreuve des bosses et de la rouille
• Une calandre distinctive, un grand repose-pied, et les ailes monoblocs complètent le style.

Xenoy est une marque de commerce de SABIC Innovative Plastics.

Le corps de tondeuse Accel Deep de 122 cm (48 po) en acier embouti, doté d’une coque profonde et d’un dessus plat, offre une coupe d’excellente qualité et une productivité remarquable, et est facile à nettoyer, durable et polyvalent. Il fournit un rendement optimal et assure une excellente dispersion des brins d’herbe coupée, même à grande vitesse :

• Profondeur de 12,3 cm (4,8 po) sur l’ensemble de la coque, ce qui assure un rendement optimal lors de la tonte, du hachage et de l’ensachage
  • L’accessoire MulchControl™ offert en option est polyvalent et assure un hachage de rendement supérieur.
• Parce que le corps est fait en acier embouti, il ne présente aucune arête vive et aucun coin où la matière pourrait s’accumuler et réduire le rendement de la tonte
• Le corps de tondeuse est suspendu, ce qui assure une coupe uniforme et de niveau.
  • Les roues de la tondeuse sont réglables et sont situées juste au-dessus du sol, ce qui réduit les dégâts pouvant être causés sur le terrain.

Excellente qualité de coupe

Ce corps de tondeuse profond en acier embouti procure une coupe d’excellente qualité. Il offre suffisamment d’espace pour évacuer l’herbe coupée en suspension sans qu’elle soit coupée de nouveau :

• La puissance de la tondeuse sert à couper l’herbe une seule fois, ce qui améliore grandement sa capacité de coupe.
  • Cela permet de garder une excellente qualité de coupe à grande vitesse.
• Le débit constant des matières éjectées empêche l’herbe déjà coupée d’entrer en contact avec l’herbe à couper, ce qui assure une coupe nette.
• En mode de hachage, la coupe est également plus uniforme que celle qu’offrent d’autres types de conception ; la profondeur accrue du corps permet à l’herbe coupée de circuler de façon continue, ce qui optimise le hachage et assure une distribution uniforme des brins d’herbe coupée.

Productivité – accélère le travail

Le corps de tondeuse profond en acier embouti permet d’accroître la productivité, donc d’accélérer le travail. Il offre suffisamment d’espace pour évacuer l’herbe coupée en suspension sans la couper de nouveau, ce qui permet de concentrer la puissance de la tondeuse sur l’herbe à couper :

• Améliore grandement la capacité de la tondeuse à assurer un excellent rendement de tonte dans les conditions difficiles et à grande vitesse

La grande goulotte d’éjection, à la fois haute et large, laisse passer un grand volume de matière :

• Elle assure une éjection uniforme des brins d’herbe coupée quelle que soit la vitesse de tonte
• Elle réduit les risques d’obstruction, ce qui est particulièrement important durant la tonte de gazon épais, dense ou humide ou durant l’ensachage
• Le souffleur Power Flow™ de la tondeuse 48A est doté d’un boîtier d’entrée qui est 50 pour cent plus grand que celle des souffleurs Power Flow 48X utilisés sur les machines de génération antérieure

Propreté – à la fois pour la tondeuse et pour le conducteur

Grâce à son dessus plat, le corps de tondeuse en acier embouti demeure propre et permet au conducteur de ne pas se salir :

• Le corps de tondeuse ne présente que très peu d’endroits, sur le dessus ou en dessous, où l’herbe coupée peut s’accumuler.
  • Le dessus du corps demeure propre, ce qui réduit le temps nécessaire au nettoyage et à l’entretien.
  • La partie inférieure du corps est auto-nettoyante, ce qui prévient l’accumulation de matières pouvant nuire à la circulation de l’air et des brins d’herbe coupée et lui assure un rendement optimal.
  • Il n’est pas nécessaire de procéder aussi souvent au nettoyage et au retrait des matières accumulées au niveau de la partie inférieure du corps de la tondeuse.
• La profondeur du corps de la tondeuse Accel Deep réduit la quantité de brins d’herbe coupée qui s’échappe par l’avant de la tondeuse
  • La quantité de brins d’herbe coupée qui aboutissent sur le poste de conduite et sur le corps de tondeuse est négligeable.
  • Même en ce qui concerne les matières éjectées par la goulotte, les brins d’herbe sont plus longs, parce qu’ils ne sont coupés qu’une seule fois, ils sont donc moins susceptibles d’aboutir sur le conducteur
  • Le hachage empêche complètement l’éjection de matières et l’accessoire MulchControl fait en sorte que le hachage constitue une solution pratique dans la plupart des situations de tonte.

Le nettoyage du corps de tondeuse, sur le dessus et en dessous, est l’une des activités d’entretien les plus fréquentes :

• Le dessus plat du corps de tondeuse offre peu d’endroits où les brins d’herbe coupée peuvent s’accumuler et facilite le retrait des matières qui réussissent malgré tout à s’y accumuler.

Option MulchControl

L’accessoire MulchControl conçu pour le corps de tondeuse 48A fait du hachage le mode de choix dans de nombreuses situations de tonte. En effet, il offre non seulement un excellent rendement en matière de hachage, mais il permet également de passer facilement au mode d’éjection latérale ou d’ensachage, selon les besoins. Le hachage des brins d’herbe coupée procure les avantages suivants :

• Il donne une pelouse magnifique
• Il prévient la projection des brins d’herbe coupée sur le conducteur, les allées ou les massifs de fleurs
• Il réduit la quantité d’engrais nécessaire
• Il élimine l’effort nécessaire pour récupérer les brins d’herbe coupée

Un orifice facilite le lavage de la partie inférieure du corps de tondeuse.

• Un raccord de tuyau est offert de série avec le corps de tondeuse.

La durabilité supérieure est intégrée à la conception

Le corps de tondeuse 48A est doté de logements robustes pour les moyeux de lames ; les lames demeurent donc alignées, même après des années d’utilisation intensive :

• Les nervures accroissent la robustesse de la coque.
• Le poids global du corps de tondeuse 48A est de 23 pour cent supérieur à celui du corps de tondeuse Edge™ Xtra de 122 cm (48 po) utilisé sur les machines de génération antérieure.

Les roues de la tondeuse sont renforcées :

• Cet accroissement de leur robustesse et de leur durabilité en prolonge donc l’utilisation et en réduit l’entretien.
• Le réglage de la hauteur des roues pour obtenir la hauteur de coupe souhaitée est facile et rapide.

Grâce à la conception du système d’entraînement qui utilise une courroie à faible tension, la charge latérale subie par les roulements inférieurs du moteur et les roulements du corps de tondeuse est plus faible, ce qui accroît la durée d’utilisation.

Le corps de tondeuse 48A est doté d’un pare-chocs fabriqué à partir d’une tige d’acier massif de 16 mm (5/8 po) de diamètre qui accroît sa robustesse et offre une meilleure protection.

La peinture appliquée en deux étapes avec une machine à enduire de type E et la peinture en poudre fournissent une protection supplémentaire contre la rouille.

Polyvalence – il est facile de passer du mode d’éjection latérale aux modes de hachage et d’ensachage.

La tondeuse 48A est conçue pour offrir une polyvalence optimale, en permettant de passer facilement d’un mode à un autre :

• Avec l’accessoire MulchControl, offert en option (en plus des lames de hachage spéciales), le passage du mode d’éjection latérale au mode de hachage, et vice-versa, se fait simplement au moyen d’un levier.
• Le sac récupérateur d’herbe arrière Power Flow peut être utilisé lorsque l’accessoire MulchControl et les lames sont posés ; pour ce faire, il suffit de placer le levier de l’accessoire MulchControl en position d’éjection latérale.

Fonctionnement de l’accessoire MulchControl

L’accessoire MulchControl, de conception simple et innovante, est facile à utiliser et à entretenir :

• L’accessoire MulchControl des déflecteurs permettant de réguler la circulation des brins d’herbe coupée sous le corps de tondeuse.
  • Le déflecteur, ou séparateur, de l’accessoire MulchControl est situé entre les moyeux central et de gauche et se trouve environ à mi-chemin du sol. Sa hauteur permet d’assurer l’équilibre entre les modes de hachage et d’éjection latérale.
  • Lorsque le déflecteur MulchControl est ouvert, le séparateur situé entre les moyeux central et de gauche fait passer une partie de la matière par l’orifice d’éjection, en plus de la matière provenant des zones situées autour des moyeux centraux et de droite.
  • Lorsque le déflecteur MulchControl est fermé, l’herbe coupée reste sous le corps de tondeuse et est hachée et déposée sur le gazon.

• La poignée de l’accessoire MulchControl se trouve sur le dessus du corps de tondeuse et sert à ouvrir et à fermer le déflecteur d’éjection.
  • Le conducteur doit donc descendre de la tondeuse pour engager ou désengager le mode de hachage.
• Le passage du mode de hachage au mode d’éjection latérale ou vice-versa ne prend que quelques secondes.

L’accessoire MulchControl convient aux situations suivantes :

• Lorsque le conducteur procède habituellement au hachage de l’herbe, mais qu’il veut passer au mode d’éjection latérale si l’herbe est trop longue
• Lorsque le conducteur utilise habituellement l’éjection latérale, mais qu’il souhaite pouvoir fermer la goulotte afin de réduire la quantité de brins d’herbe coupée
• Lorsque le conducteur souhaite rester en mode de hachage sur la pelouse principale, mais qu’il a souvent recours à l’éjection latérale sur les pelouses secondaires
• Lorsqu’il procède à l’ensachage des brins d’herbe coupée, mais qu’il veut tondre le plus longtemps possible avant de devoir vider les sacs

L’accessoire MulchControl permet au conducteur de décider du traitement de l’herbe coupée. Désormais, le conducteur bénéficie de tous les avantages du hachage tout en ayant la possibilité de passer facilement à l’éjection latérale ou à l’ensachage au besoin.

Sac récupérateur d’herbe arrière Power Flow de 247 l (7 boisseaux)

Un système récupération arrière de 247 l (7 boisseaux) est disponible en option. Ce système permet de ramasser efficacement les brins d’herbe coupée et les feuilles :

• Le souffleur Power Flow et la goulotte sont faciles à poser. Le souffleur Power Flow pivote vers l’extérieur, ce qui facilite le vidage et le nettoyage.
• La conception de la trémie, de style moderne, offre un excellent rendement lors de l’ensachage, un fonctionnement plus propre et des sacs faciles à vider :
  
  • Capacité de 247 l (7 boisseaux)
  • Souffleur Power Flow facile à poser (à commander séparément)
  • Goulotte facile à poser (à commander séparément)
  • Conduite d’évacuation de l’air
  • Verrou à ressort pratique
  • Indicateur de remplissage selon le débit d’air
  • Système de montage Quik-Tatch
  • Haut de la trémie étanche
  • Sacs en tissu souple disponibles

En mode d’éjection latérale, l’accessoire MulchControl continue de hacher environ le tiers de l’herbe coupée. Par conséquent, il s’agit d’un mode de hachage partiel. Ce mode peut être avantageux durant l’éjection latérale de l’herbe coupée ou l’ensachage, car il réduit le volume d’herbe rejetée. Néanmoins, il présente parfois des inconvénients dans les cas suivants :

• Lorsque l’herbe est coriace, comme le gazon de Manille et l’herbe des Bermudes dans le sud des États-Unis
• Lorsque l’herbe est humide ou très longue, ce qui est fréquent dans la région du Pacifique nord-ouest des États-Unis
• Lorsqu’il est souhaitable de débarrasser le plus possible la pelouse des brins d’herbe coupée en optimisant l’ensachage

Le châssis est fabriqué en acier robuste formé et soudé et est renforcé en certains points afin d’en améliorer la solidité :

• Le châssis est fabriqué en acier de calibre 12 et de 2,66 mm (0,105 po) d’épaisseur.
• La plaque d’attelage arrière en acier de 6,4 mm (0,25 po) complète l’assemblage du châssis.
• La plaque d’attelage arrière peut supporter jusqu’à quatre masses Quik-Tatch de 19 kg (42 lb).
• Le pare-chocs avant optionnel pour le tracteur X570 peut supporter jusqu’à quatre masses Quik-Tatch de 19 kg (42 lb).

Le tracteur est propulsé par un groupe moteurs iTorque™ de John Deere ; l’ensemble des caractéristiques du moteur et le capot de conception exclusive assurent une puissance de traction accrue, un refroidissement uniforme et une grande durabilité. Les principales caractéristiques du moteur sont les suivantes :

• 17,9 kW (24 HP)
• Grosse cylindrée de 726 cm³
• Moteur à 2 cylindres en V refroidi à l’air
  • Une puissance et un rendement supérieurs
  • Moteur à fonctionnement régulier et silencieux
  • Démarrages faciles
• Parmi les caractéristiques de qualité, il y a notamment :
  • Les chemises de cylindre en fonte
  • Les soupapes en tête
  • Le système de lubrification sous pression intégral
  • Le filtre à huile interchangeable
  • Le filtre à air à double effet
• Démarreur à solénoïde pour simplifier les démarrages, même par temps froid

Alternateur à volant

Un alternateur à volant génère suffisamment d’électricité pour recharger rapidement la batterie et alimenter les accessoires électriques, comme les phares ou un pulvérisateur :

• Capacité de 15 ampères
• Régulé afin de maintenir la pleine charge de la batterie sans la surcharger

Le corps de tondeuse Accel Deep de 137 cm (54 po) en acier embouti, qui est caractérisé par une coque profonde et un dessus plat, offre une coupe d’excellente qualité et une productivité remarquable, et est facile à nettoyer, durable et polyvalent. Il offre un rendement optimal et assure une excellente dispersion des brins d’herbe coupée, même à grande vitesse :

• Profondeur de 12,3 cm (4,8 po) sur l’ensemble de la coque, ce qui assure un rendement optimal lors de la tonte, du hachage et de l’ensachage
  • L’accessoire MulchControl™ offert en option est polyvalent et assure un hachage de rendement supérieur.
• Parce que le corps est fait en acier embouti, il ne présente aucune arête vive et aucun coin où la matière pourrait s’accumuler et réduire le rendement de la tonte.
• Le corps de tondeuse est suspendu, ce qui assure une coupe uniforme et de niveau.
  • Les roues de la tondeuse sont réglables et sont situées juste au-dessus du sol, ce qui réduit les dégâts pouvant être causés sur le terrain.

Excellente qualité de coupe

Le corps de tondeuse profond en acier embouti offre une coupe d’excellente qualité. Il offre à l’herbe coupée en suspension suffisamment d’espace pour être évacuée sans être coupée à nouveau :

• La puissance de la tondeuse sert à couper l’herbe une seule fois, ce qui améliore grandement sa capacité de coupe.
  • Assure une excellente qualité de coupe à grande vitesse
• Le débit constant des matières éjectées empêche l’herbe déjà coupée d’entrer en contact avec l’herbe à couper, ce qui assure une coupe nette.
• En mode de hachage, la coupe est également plus uniforme que celle qu’offrent d’autres types de conception; la profondeur accrue du corps permet à l’herbe coupée de circuler de façon continue, ce qui optimise le hachage et assure une distribution uniforme des brins d’herbe coupée.

Productivité – accélère le travail

Le corps de tondeuse profond en acier embouti offre une productivité accrue, ce qui accélère le travail. Il offre à l’herbe coupée en suspension suffisamment d’espace pour être évacuée rapidement sans être coupée à nouveau, ce qui permet de concentrer la puissance de la tondeuse sur l’herbe à couper :

• Fait en sorte que la tondeuse offre un excellent rendement de tonte dans les conditions difficiles et à grande vitesse

La grande goulotte d’éjection, qui est à la fois haute et large, permet d’éjecter un grand volume de matière :

• Assure une éjection uniforme des brins d’herbe coupée quelle que soit la vitesse de tonte
• Réduit les risques d’obstruction, ce qui est particulièrement important durant la tonte de gazon épais, dense ou humide ou durant l’ensachage
• Le souffleur Power Flow™ de la tondeuse 54A est doté d’une entrée qui est 20 pour cent plus grande que celle des souffleurs Power Flow 54X utilisés sur les machines de génération antérieure

Propreté – à la fois pour la tondeuse et pour le conducteur

Grâce à son dessus plat, le corps de tondeuse en acier embouti demeure propre et permet au conducteur de ne pas se salir :

• Le corps de tondeuse ne présente que très peu d’endroits, sur le dessus ou en dessous, où l’herbe coupée peut s’accumuler.
  • Le dessus du corps demeure propre, ce qui réduit le temps et les efforts consacrés au nettoyage et à l’entretien
  • Le dessous du corps est autonettoyant, ce qui prévient l’accumulation de matières pouvant nuire à la circulation de l’air et des brins d’herbe coupée et lui assure un rendement optimal
  • Il n’est pas nécessaire de procéder aussi souvent au nettoyage et au retrait des matières accumulées sous le corps de la tondeuse
• La profondeur du corps de tondeuse Accel Deep réduit la quantité de brins d’herbe coupée qui s’échappe par l’avant de la tondeuse
  • La quantité de brins d’herbe coupée qui aboutissent sur le conducteur et sur le corps de tondeuse est négligeable
  • Même en ce qui concerne les matières éjectées par la goulotte, le fait que les brins d’herbe sont plus longs, parce qu’ils ne sont coupés qu’une seule fois, fait en sorte qu’ils sont moins susceptibles d’aboutir sur le conducteur
  • Le hachage empêche complètement l’éjection de matières et l’accessoire MulchControl fait en sorte que le hachage constitue une solution pratique dans la plupart des situations de tonte

Fonctionnement de l’accessoire MulchControl

L’accessoire MulchControl est de conception simple et innovante et est facile à utiliser et à entretenir.

• Il comprend des déflecteurs permettant de réguler la circulation des brins d’herbe coupée sous le corps de tondeuse.
  • La partie gauche du corps de tondeuse est complètement fermée et optimisée pour le hachage; le hachage a donc lieu même lorsque la tondeuse est en mode d’éjection latérale.
  • Les déflecteurs entourant la partie centrale et les lames du côté droit sont optimisés pour le hachage lorsque le déflecteur d’éjection est fermé.

Le nettoyage du corps de tondeuse, sur le dessus et en dessous, est l’une des activités d’entretien les plus fréquentes :

• Le dessus plat du corps de tondeuse offre peu d’endroits où les brins d’herbe coupée peuvent s’accumuler et facilite le retrait des matières qui réussissent malgré tout à s’accumuler.

Un orifice facilite le nettoyage du dessous du corps de tondeuse.

• Un raccord de tuyau est offert de série avec le corps de tondeuse.

La durabilité supérieure est intégrée à la conception

Le corps de tondeuse 54A est doté de logements robustes pour les moyeux de lames; les lames demeurent donc alignées, même après des années d’utilisation intensive :

• Les nervures de la coque lui confèrent une robustesse accrue
• Le poids global du corps de tondeuse 54A est de 3 pour cent supérieur à celui du corps de tondeuse Edge Xtra™ de 137 cm (54 po) utilisé sur les machines de génération antérieure.

Les roues de la tondeuse sont renforcées :

• Cela leur procure une robustesse et une durabilité accrues; elles peuvent donc être utilisées longtemps sans problèmes.
• Le réglage de la hauteur des roues pour obtenir la hauteur de coupe souhaitée est facile et rapide.

Grâce à la conception du système d’entraînement qui utilise une courroie à faible tension, la charge latérale subie par les roulements inférieurs du moteur et les roulements du corps de tondeuse est plus faible, ce qui accroît la durée d’utilisation.

Le corps de tondeuse 54A est doté d’un pare-chocs fabriqué à partir d’une tige d’acier massif de 16 mm (5/8 po) de diamètre qui accroît sa robustesse et offre une meilleure protection.

 

Le procédé de peinture en deux étapes, dont un revêtement selon la méthode électrophorétique et l’application d’une peinture en poudre, procure une protection supplémentaire contre la rouille.

Polyvalence – Il est facile de passer du mode d’éjection latérale, aux modes de hachage et d’ensachage

La tondeuse 54A est conçue pour offrir une polyvalence optimale, en permettant de passer facilement d’un mode à un autre :

• Lorsque l’accessoire MulchControl, offert en option, est installé (en plus des lames de hachage spéciales), il est possible de passer du mode d’éjection latérale au mode de hachage, et vice-versa, en faisant simplement basculer un levier.
• Le sac récupérateur d’herbe arrière Power Flow peut être utilisé lorsque l’accessoire MulchControl et les lames sont installés; pour ce faire, il suffit de placer le levier de l’accessoire MulchControl en position d’éjection latérale.

Option MulchControl

L’accessoire MulchControl conçu pour le corps de tondeuse 54A fait du hachage le mode de choix dans de nombreuses situations de tonte. En effet, non seulement il offre un excellent rendement en matière de hachage, mais il permet également de passer facilement au mode d’éjection latérale ou d’ensachage, selon les besoins. Le hachage de l’herbe coupée procure les avantages suivants :

• Une pelouse magnifique
• Prévient la projection de l’herbe coupée sur le conducteur, dans les allées ou sur les massifs de fleurs
• Réduit la quantité d’engrais nécessaire
• Aucun effort nécessaire pour éliminer les brins d’herbe coupée

Sac récupérateur d’herbe arrière Power Flow de 230 l (6,5 boisseaux)

Le souffleur Power Flow et la goulotte sont faciles à installer. Le souffleur Power Flow peut pivoter, ce qui facilite le vidage et le nettoyage.

• La poignée de l’accessoire MulchControl se trouve sur le dessus du corps de tondeuse et sert à ouvrir ou à fermer le déflecteur d’éjection.
  • Le conducteur doit donc descendre de la machine pour activer ou désactiver le mode de hachage.
• Le passage du mode de hachage au mode d’éjection latérale ou vice-versa ne prend que quelques secondes.

L’accessoire MulchControl convient aux situations suivantes :

• Lorsque le conducteur procède habituellement au hachage de l’herbe, mais qu’il souhaite pouvoir passer au mode d’éjection latérale si l’herbe est trop longue
• Lorsque le conducteur utilise habituellement l’éjection latérale, mais qu’il souhaite pouvoir fermer la goulotte afin de réduire la quantité de brins d’herbe coupée qui est rejetée
• Lorsqu’il est toujours en mode de hachage sur la pelouse principale, mais qu’il a souvent recours à l’éjection latérale sur les pelouses secondaires
• Lorsqu’il procède à l’ensachage des brins d’herbe coupée, mais qu’il souhaite tondre le plus longtemps possible avant de devoir vider les sacs

L’accessoire MulchControl permet au conducteur de décider comment disposer de l’herbe coupée. Désormais, le conducteur bénéficie de tous les avantages du hachage tout en ayant la possibilité de passer facilement à l’éjection latérale ou à l’ensachage au besoin.

 

En mode d’éjection latérale, l’accessoire MulchControl continue de hacher environ le tiers de l’herbe coupée. Par conséquent, il s’agit essentiellement d’un mode de hachage partiel. Ce mode peut être avantageux pour l’éjection latérale de l’herbe coupée ou pour l’ensachage, car il permet de réduire le volume d’herbe rejetée. Néanmoins, il présente parfois des inconvénients dans les cas suivants :

• Lors de la tonte d’herbe coriace, comme le gazon de Manille et l’herbe des Bermudes dans les régions du sud des États-Unis
• Lorsque l’herbe est humide ou très longue, ce qui est fréquent dans la région du Pacifique ou du nord-ouest des États-Unis
• Lorsqu’il est souhaitable de débarrasser le plus possible la pelouse des brins d’herbe coupée en optimisant l’ensachage

Every owner of a John riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak™ or ZTrak™ mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

• The cart has a premium molded, high-density polyethylene box construction.
• Compression molding process allows polyethyl­ene to be the optimum thickness in all areas for superior strength and durability.
• Polyethylene body will not rust or dent; it stays looking new longer.
• 0.75-in. (2-cm) x 2-in. (5-cm) stake pockets are molded in to make the addition of side extensions easy.
• Two vertical 0.75-in. (2-cm) molded channels on each side allow easy use of dividers to separate the box into two or three compartments.
• Ribs in the box bottom add strength and prevent the shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• Pneumatic tires provide turf tread for good flotation, shock absorption, and minimal rolling resistance.

Wheels

Wheels are mounted on a solid, one-piece axle for durability.
 
Iron and Oilite® wheel bearings with grease fittings provide lubrication for long life.

The pneumatic tires offer the following:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Sloped tailgate

A sloped tailgate design makes emptying the box easier; there is no tailgate to loosen or remove.

Tractor hitch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

Tilt latch

An easy-to-use, spring-loaded dump latch allows tilting the box for easier unloading. A steep dump angle makes emptying the cart easier.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

7P Poly Utility Cart
Order number: LP21935

Oilite is a trademark of Beemer Precision, Incorporated.

The 8-cu-ft (0.23-m³), 300-lb (136-kg) capacity 8Y Convertible Cart can be used to haul a variety of materials including lawn debris, sand, dirt, mulch, and plants. The unique convertible hitch allows changing the cart from tow-behind mode to push mode without tools.

Key features include:

• Compatible with riding lawn tractors and garden tractors
• Durable poly construction
• All-terrain pneumatic tires
• Converts from tow cart to push cart without tools
• Large handle is provided for ease of use

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials including firewood, lawn debris, sand, dirt, mulch, garden tools, plants, and bushes. Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.
 
NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck. 

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not  exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite® bearings	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

8Y Convertible Cart
Order number: LP22755

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

The 10P Utility Cart is designed, painted, and decaled to be compatible with other John Deere equipment:

• Large 650-lb (295-kg) capacity
• 10-cu ft (283-L), heavy-duty, 0.25-in. (6.4-mm) thick poly bed
• Will not dent or rust
• 15x6 tubeless pneumatic tires with turf tread for maximum traction
• Easy, hands-free foot pedal dump release
• Steep dump angle for complete emptying

 

A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.

 

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite® bearings	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (2) 42-lb (19-kg) plastic shell wheel weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information
Please contact a local John Deere dealer for availability and pricing information.

10P Utility Cart
Order number: LPPCT10JD

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential customer for a high-quality, affordable utility cart. Utility carts can be used to haul a variety of materials, including firewood, lawn debris, dirt, sand, mulch, garden tools, plants, and bushes.

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. See the appropriate vehicle pages for the weight of the vehicle and the mower deck.

Welded box construction provides maximum reliability:

• Requires less setup time than the bolted construction.
• Box sides and bottom are one piece and have rounded corners and no hardware for easy cleaning.

Wheels and tires

Wheels are mounted on a solid, one-piece axle for durability.

Iron/Oilite® wheel bearings with grease fittings provide lubrication for long life.

Pneumatic tires offer:

• Good flotation
• Minimal rolling resistance
• Shock absorption

Turf-tread tires are used on the 13 Utility Cart.

Deluxe tailgate is hinged for easy emptying and can also be quickly removed without the use of tools.

Easy hookup and tilt-dump latch

A large-diameter hitch pin provides plenty of strength:

• Fast, easy attachment to the tractor hitch
• Spring pin to ensure the pin stays in place

The easy-to-use latch allows tilting the bed for easier unloading:

• Steep dump angle makes emptying easier.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

13 Utility Cart
Order number: LPHDC13JD

Oilite is a trademark of Beemer Precision, Incorporated.

Every owner of a John Deere riding lawn and garden product is a potential user of a high-quality, affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

 

Key features of the 17P Utility Cart:

• 1,000-lb (454-kg), 17-cu ft (0.48-m³) load capacity.
• Cart has premium molded high-density polyethylene box construction.
• Compression molding process allows polyethyl­ene to be the optimum thickness in all areas for superior strength and durability.
• Polyethylene body will not rust or dent, staying new-looking longer.
• 0.75- x 2-in. (19- x 51-mm) stake pockets are molded in to make addition of side extensions easy.
• Two vertical 0.75-in. (19-mm) molded channels on each side allow for easy use of dividers to separate the box into two or three compartments.
• Ribs in box bottom add strength and prevent a shovel from hitting bolts when emptying the cart.
• Sloped tailgate design makes emptying the box easier; no tailgate to loosen or remove.
• Styling is compatible with other John Deere equipment.
• 16x6.5 pneumatic tires with turf tread give good flotation, shock absorption, and minimal rolling resistance.
• Wheels are mounted on a solid one-piece axle.
• Wheels turn on iron/Oilite® bushings with grease fitting for long life.
• Spring-loaded dump latch is easy to use.

A convenient foot pedal dump release kit, LP48017, which now comes standard on all 10P and 17P carts is available to retrofit existing poly carts. This kit allows the operator to use both hands to lift the cart bed for more natural and efficient unloading.

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

 

17P Utility Cart
Order number: LPPCT17JD

Oilite is a trademark of Beemer Precision Incorporated.

Everyone who owns a John Deere riding lawn and garden product is a potential user of a high-quality affordable utility cart.

Utility carts can be used to haul a variety of materials:

• Firewood
• Lawn debris
• Sand
• Dirt
• Mulch
• Garden tools
• Plants and bushes

Utility carts are designed, painted, and decaled to be compatible with other John Deere equipment.

Durable box design

Durable 18-gauge, 0.05-in. (1.2-mm) (10S) or 16-gauge, 0.06-in. (1.5-mm) (16S) steel components are bolted together.

 

Recessed bolts are used in the bottom of the box, so they will not interfere with emptying the cart.

Convenient emptying of box

The deluxe tailgate is hinged for easy emptying and can also be quickly removed without the use of tools.

 

Model comparison chart

Comparison with similar models

Model	Order through	Box capacity (heaped)	Material thickness	Maximum weight	Vehicle compatibility
7P	Order Zone	7 cu ft (0.20 m3)	Polypropylene	450 lb* (204 kg)	EZtrak™, ZTrak™, 100 Series, S240, X300 Series, X500 Series, X700 Series
8Y	Order Zone	8 cu ft (0.22 m3)	Polypropylene	300 lb* (136 kg) (tow)	100 Series, S240, X300 Series, X500 Series, X700 Series
10P	Order Zone	10 cu ft (0.28 m3)	Polypropylene	650 lb* (295 kg)	EZtrak, ZTrak, 100 Series, S240, X300 Series, X500 Series, X700 Series
13	Order Zone	13 cu ft (0.37 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,105 lb* (501 kg)	X500 Series, X700 Series
17P	Order Zone	17 cu ft (0.48 m3)	Polypropylene	1,000 lb* (454 kg)	100 Series, S240, X300 Series, X500 Series, X700 Series
18	Order Zone	18 cu ft (0.51 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,650 lb* (748 kg)	X500 Series, X700 Series
21	Order Zone	21 cu ft (0.59 m3)	16-gauge, 0.06-in. (1.5-mm) steel	1,016 lb* (461 kg)	X500 Series, X700 Series

*The total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower shoud not exceed 250 lb (113.4 kg). The maximum weight for the 21 Utility Cart is rated at 20 mph (32.2 km/h).

Specifications

 

	7P	8Y	10P	13	17P	18	21
Box capacity
Heaped	7 cu ft (0.20 m3)	8 cu ft (0.22 m3)	10 cu ft (0.28 m3)	13 cu ft (0.37 m3)	17 cu ft (0.48 m3)	18 cu ft (0.51 m3)	21 cu ft (0.59 m3)
Struck	5.6 cu ft (0.16 m3)	6.6 cu ft (0.19 m3)	8.3 cu ft (0.24 m3)	10 cu ft (0.28 m3)	14 cu ft (0.40 m3)	15 cu ft (0.42 m3)	15 cu ft (0.42 m3)
Maximum load	500 lb* (226 kg)	300 lb* (136 kg)	650 lb* (295 kg)	1,105 lb* (501 kg)	1,000 lb* (454 kg)	1,650 lb* (748 kg)	1,000 lb* (454 kg)
Box dimensions
Width	33 in. (84 cm)	33.68 in. (85.5 cm)	30.3 in. (77 cm)	30.25 in. (76.8 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Length	45 in. (114 cm)	45 in. (114 cm)	44.5 in. (113 cm)	48 in. (122 cm)	58.5 in. (148.6 cm)	48 in. (122 cm)	48 in. (122 cm)
Depth	10.5 in. (27 cm)	10.75 in. (27.3cm)	12 in. (30.5 cm)	12 in. (30.5 cm)	15.5 in. (39.4 cm)	18 in. (45.7 cm)	11 in. (27.9 cm)
Box construction	Molded	Molded	Molded	Welded	Molded	Welded	Bolted
Material	High-density polyethylene (HDPE)**	HDPE** w/UV inhibitor	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	HDPE**	16-gauge, 0.06-in. (1.5-mm) steel	16-gauge, 0.06-in. (1.5-mm) steel
Tailgate	None, sloped	None, sloped	None, sloped	Hinged	None, sloped	Hinged	Lift-out/swing-out
Pneumatic tires	2 ply	---	2 ply	2 ply	4 ply	4 ply	2 ply
Size	12x4x6	13x4x6	15x6.00-6	15x6.00-6	16x6.50-8	16x6.50-8	20x10.00-8
Tread design	Turf	Knobby	Turf	Turf	Turf	Turf	Turf
Recommended inflation pressure	30 psi (207 kPa)	30 psi (207 kPa)	14 psi (97 kPa)	14 psi (97 kPa)	28 psi (193 kPa)	28 psi (193 kPa)	10 psi (70 kPa)
Wheel bearings	Iron/Oilite® bearings	None	Iron/Oilite	Iron/Oilite	Iron/Oilite	Iron/Oilite	Ball bearings, double sealed
Grease fittings on wheels	Yes	None	Yes	Yes	Yes	Yes	None
Axle diameter	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	0.75 in. (1.905 cm)	1 in. (2.54 cm)	1 in. (2.54 cm)
Ground clearance	5.62 in. (14.3 cm)	5.25 in. (13.3 cm)	6.5 in. (16.5 cm)	6.5 in. (16.5 cm)	14.25 in. (36.2 cm)	7 in. (17.8 cm)	8.25 in. (21 cm)
Width, overall	34 in. (86.4 cm)	33.68 in. (85.5 cm)	38 in. (96.5 cm)	38 in. (96.5 cm)	39.5 in. (100.3 cm)	38 in. (96.5 cm)	48 in. (122 cm)
Hitch pin	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip	Pin/spring clip
Dump angles	55 degrees	55 degrees	56 degrees	31 degrees	46 degrees	31 degrees	35 degrees
Maximum tongue weight	100 lb (45.4 kg)	100 lb (45.4 kg)	70 lb (31.75 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)	100 lb (45.4 kg)
Shipping weight with carton	68 lb (31 kg)	65 lb (29.5 kg)	79 lb (35.8 kg)	110 lb (49.9 kg)	105 lb (47.6 kg)	170 lb (77.1 kg)	240 lb (109 kg)
Net weight	65 lb (29 kg)	55 lb (25 kg)	72 lb (32.7 kg)	105 lb (47.6 kg)	105 lb (47.6 kg)	150 lb (68 kg)	220 lb (99.8 kg)

*Total weight of the cart and payload. For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg).

**HDPE is compression molded for optimum thickness in all areas and maximum durability.

Tractor compatibility and requirements

Utility Carts

Chart below shows vehicle compatibility.

An X indicates cart can be used with the pulling unit.

NOTE: For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). The chart shows which utility carts are compatible with the vehicle.

 

	7P	8Y	10P	13	17P	18	21
EZtrak Z225, Z235, Z245, Z255, Z425, Z435, Z445, Z465, Z625, Z645, Z655, Z665 ZTrak Z335E, Z355E, Z525E, Z535M, Z540M, Z535R, Z540R	X		X
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D125, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	X	X	X		X
S240	X	X	X		X
LT150, LT160, LT180, LT190, LTR180	X	X	X		X
LX280, LX280AWS, LX289	X	X	X		X
X300, X300R, X304, X310, X320, X324, X340, X360 X330, X350, X350R, X354, X370, X380, X384, X390, X394	X	X	X		X
SST15, SST16, SST18	X	X	X
G110	X	X	X	X	X
GT235, GT245	X	X	X	X	X
GX255, GX335, GX345, GX355	X	X	X	X	X
X500, X520, X530, X534, X540 X570, X580, X584, X590	X	X	X	X	X
X465, X475, X485, X495, X575, X585, X595	X	X	X	X	X	X	X
X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	X	X	X	X	X	X	X

For proper braking and operation, the loaded weight of the cart should never exceed the weight of the tractor, or other towing unit, plus the operator. The loaded weight of any equipment towed by an EZtrak or ZTrak mower should not exceed 250 lb (113.4 kg). See the appropriate vehicle pages for the weight of the vehicle and the mower deck. Additional weight can be added to the vehicle by the following methods:

  

Tractor
L100, L108, L110, L111, L118, L120, L130 102, 115, 125, 135, 145, 155C, 190C, LA100, LA110, LA120, LA130, LA140, LA150, LA105, LA115, LA125, LA135 LE, LA135 SE, LA145, LA155, LA165, LA175, D100, D105, D110, D120, D130, D140, D150, D155, D160, D170, E100, E110, E120, E130, E140, E150, E160, E170, E180	(2) 30-lb (14-kg) wheel weights, front (2) 42-lb (19-kg) suitcase weights, rear
S240	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
LT150, LT160, LT180, LT190, LTR180	(2) 34-lb (15-kg) wheel weights, front (2) 31-lb (14.1-kg) plastic shell wheel weights, rear (not for LT190)
LX280, LX280AWS, LX289 X300, X300R, X304, X310, X320, X324, X340, X360	(2) 34-lb (15-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, rear
SST15, SST16, SST18	(1) 88-lb (40-kg) weight kit, front (3) 40-lb (18-kg) weights, rear
G100	(2) 50-lb (23-kg) wheel weights, rear (2) 42-lb (19-kg) suitcase weights, rear
G110	(2) 50-lb (23-kg) plastic shell rear wheel weights
GT235, GT245	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear
GX255, GX335, GX345, GX355 X500, X520, X530, X534, X540 X570, X580, X584, X590	(2) 30-lb (14-kg) wheel weights, front (4) 42-lb (19-kg) suitcase weights, front (4) 42-lb (19-kg) suitcase weights, rear (4) 50-lb (23-kg) wheel weights, rear (2) 50-lb (23-kg) wheel plastic shell weights, rear
X465, X475, X485, X495, X575, X585, X595 X700, X720, X724, X728, X729, X740, X744, X748, X749 X710, X730, X734, X738, X739, X750, X754, X758	(4) 42-lb (19-kg) suitcase weights, front (2) 70-lb (32-kg) wheel cast-iron starter weights, rear (4) 50-lb (23-kg) cast-iron wheel weights, rear (2) 50-lb (23-kg) plastic shell wheel weights, rear (6) 42-lb (19-kg) suitcase weights, rear

Ordering information
Please contact your local John Deere dealer for availability and pricing information.

18 Utility Cart
Order number: LPHDC18JD

Oilite is a trademark of Beemer Precision, Incorporated.

35 W sealed-beam bulb provides additional lighting for evening operation.

Light swivels and tilts to allow positioning beam on work area.

Light is designed for mounting on rear fender by drilling a hole in the desired location.

The 40-in. (102-cm) Tractor Shovel expands the usefulness of any John Deere Select Series^TM X300 or X500 Multi-Terrain Tractor by allowing it to pick up and move material. It utilizes a high-capacity electric actuator that provides lift, lower, dump, and down force functions. No front blade is required.

The tractor shovel takes the back-breaking labor out of jobs like moving mulch, spreading gravel, ground grading, and more. It installs using the tractor's existing frame holes. After initial installation, it can be removed or installed without tools.

The innovative opening design of the tractor shovel, combined with the lift height, assures complete emptying of material. The tractor shovel can also be used for scraping and grading by locking the shovel in the raised position.

Tractor recommendations and requirements:

• Rear tractor ballast recommended for improved traction
• Tire chains recommended for moving snow
• No tractor requirements

 Key features:

• Can be used when upper part of shovel is locked in the raised position as a blade (without angling capability)
• Raised and lowered with electric actuator
• Provides down force to increase scraping effectiveness of blade
• Pick-up, transport, and empty a variety of loose material including soil, gravel, mulch, and snow
• Can be removed in 10 minutes or less

Compatibility:

• LP63767 40-in. (102-cm) Tractor Shovel is Compatible with:
• Select Series X300, X300R, X304, X310, X320, X324, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

 

Unique shovel design

The unique design of the 40-in. (102-cm) Tractor Shovel allows an operator who has a Select Series™ X300 Series (including X300R and X350R) or X500 Series Multi-Terrain Tractor to use the tractor shovel for lifting and moving material as well as for typical blade functions (without blade angling), such as blading, leveling, and scraping:

• Unique shovel design empties material completely.
• Shovel can be locked in the raised position for blading applications.

Operation

The tractor shovel is operated from the tractor seat with the use of a control rod and an electric switch.

An electric actuator provides power to raise, lower, and empty the shovel.

To raise or lower the tractor shovel, use the electric switch on the tractor shovel panel.

Depress the bottom of the switch to raise the shovel and depress the top of the switch to lower the shovel.

To open the shovel for emptying, raise it completely and then pull the control rod to the yellow area of the rod and press the upper end of the electric switch.

To close the shovel, press the lower end of the electric switch until the control rod releases to the black area of the rod.

Operation of the shovel for blading or leveling

To use the tractor shovel for blading, use the handle on the right side of the shovel to raise it and then use the locking lever to lock it in the raised position.

 Specifications

 

Length of tractor shovel	40 in. (101.6 cm)
Depth of tractor shovel	11 in. (27.9 cm)
Capacity	1.7 ft3 (48 L)
Cutting blade material	0.250-in. (6.4-mm) hardened steel
Material thickness, shovel	0.125 in. (3.2 mm)
Load capacity	150 lb (68 kg), evenly distributed
Lift height	4 in. to 6 in. (10.2 cm to 15.2 cm), depending on the tractor model
Shipping weight	110 lb (50 kg)
Warranty	One-year limited warranty on parts

Tractor compatibility and requirements

The 40-in. (102-cm) Tractor Shovel is compatible with the following tractors:

• Select Series X300, X300R, X304, X310, X320, X324, X330, X340, X350, X350R, X354, X360, X370, X380, X384, X390, and X394 Tractors
• Select Series X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

Requirements and/or recommendations:

1. Rear ballast is recommended for best performance.
2. Tire chains are helpful and recommended when operating in snow.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

40-in. (102-cm) Tractor Shovel
Order number: LP63767

This fully automatic 1.5-amp battery charger and maintainer safely charges lawn and garden, RV, deep-cycle, and most batteries that require long storage periods. It is particularly useful during winter months when the vehicle is not being used regularly, to ensure the battery stays charged:

• Automatically determines if the battery is 6- or 12-V and adjusts accordingly
• Helps maintain battery in good condition and ensures it is fully charged
• Powers on to charge battery and powers off when fully charged
• 'Onboard' feature allows mounting next to the battery on collector, street rods, and other occasional-use vehicles
• 1.5-amp trickle charges small batteries in 2 to 12 hours
• Maintains large battery charges
• Hookup protection guards battery and charger from damage 

 

Includes a choice of battery connection methods:

• Standard color-coded clips to connect to any battery
• Cable with quick-disconnect plug and end loops that can be bolted to battery terminals and easily unplugged from charger when not in use

Transporting mulch, plants or debris is easier with the double bucket holder. Just attach the holder bracket to the rear of any Select Series™ X300, X500 Series Multi-Terrain, or X700 Ultimate™ Series Tractor. It is designed to carry up to 70 lb (32 kg) of material.

 

For use with standard 5-gal. (19-L) buckets - ordered separately. 

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket holder (double)
Order number: LPJD301

Bucket (5-gal.)

Order number: LPJD400 (2 required)

Transporting mulch, plants, or debris is easier with the double bucket holder. Just attach the holder bracket to the rear of any Select Series™ X300, X500 Series Multi-Terrain, or X700 Series Tractor. It is designed to carry up to 70 lb (32 kg) of material for transporting mulch, plants, yard waste, or for adding ballast.

For use with the included John Deere 5-gal. (19-L) buckets.

NOTE: May not fit all tractor models with a weather enclosure or cab installed.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket holder (double) with buckets
Order number: LPJD301W

This black 5-gal. (19-L) bucket perfectly complements the CargO Mount™ single and double bucket holders. It is made of sturdy black plastic.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Bucket - 5 gal. (19-L)
Order number: LPJD400

John Deere Fuel-Protect gasoline stabilizer is a unique formula developed to ensure optimum performance and protection year-round: 

• Has corrosion preventers
• For lawn and garden equipment and other gasoline-powered vehicles
• Ensures quick starts in all two- and four-cycle engines
• Use in gasoline, gasoline-oil mixture, and ethanol blends
• Use to treat gas cans at each fill-up or use at every fill-up of vehicle
• Keeps fuel fresh for 12 months
• Contains a fuel injector and carburetor cleaner
• 1 oz treats 2 gal.

Always use fuel stabilizer in your gasoline.

Fuel sitting in gas tanks or gas containers for more than 30 days begins to degrade. Also, blended fuels and water in gasoline can form acids that corrode fuel-system components. Protect your investment - use John Deere fuel stabilizer with corrosion preventers and prevent hard starting, surging, lack of power, poor idle, flooding, and will not run or stay running conditions caused by poor-quality fuel. Ask your local John Deere dealer or visit JDParts.

Helpful tips:

• Add fuel stabilizer every time you purchase fuel.
• Deere gasoline-powered equipment is recommended to run on a minimum of 87 octane gasoline.
• John Deere Fuel-Protect for gasoline is safe to use in all types of gasoline, including gasoline/oil mixtures and blended fuels containing up to 10 percent ethanol.
• Use plastic fuel containers to store fuel; ask your local John Deere dealer.
• For best results, use a spill-proof gas can that automatically seals the gas can vent.
• Store fuel in a cool, dry, dark place in a sealed fuel can.
• Fill tank to the top every time the machine is put away.
  • Make sure tank is drained if stored for the winter or treated if left for prolonged periods of time.

Please refer to the operator’s manual for additional recommendations and warranty information.

Fuel related issues are not considered a warrantable condition as there is no defect in the materials or workmanship of the machine. 

For more information on fuel, visit John Deere Groundscare.

1-7/8-in. (48-mm) hitch ball attaches to drawbar or rear hitch to allow towing. 0.75-in. (19-mm) diameter post thread is provided.  

 

The hitch ball is available through Parts.

LG265 home maintenance kit

Home maintenance kits are a handy and convenient way for dealers to supply a customer with the maintenance-interval parts as specified in their operator's manual.

 

The LG265 home maintenance kit includes the following:

 

Quantity	Description
1	Engine oil filter
2	Engine oil quart
1	Fuel filter
1	Air filter element
1	Air filter element foam
2	Spark plug

Features and benefits:

• Fits 17P Poly Cart (not included with MC542)
• Large 53-cu ft (1.5 m3), 42-bu (1,480-L) capacity with full 83-in. (210.8-cm) clamshell opening - perfect for fall cleanup of leaves
• Powerful 205-cc, 9.00 lb-ft* gross torque engine
• Welded steel impeller for greater suction
• Large, 8-in. (20.3-cm) diameter wire embedded hose for less clogging and larger volume pickup
• Full opening for easy access
• Vented 15-oz (425-g) poly-mesh canopy that keeps dust and exhaust away from the operator
• Contoured handles for easier open/close operation and emptying
• Custom pre-cut mower boot and welded bracket assembly for easy fit to the following John Deere Mower Decks that can be ordered separately:
  • 48, 54, and 62 in. (122, 137, and 158 cm)
  • 54- and 60-in. (137- and 152-cm) HC
  • 60-in. (152-cm) 7-Iron

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.

Specifications

 

Capacity	42 bu (1500 L), 53 cu ft (1.5 m3)
Engine	205 cc, 9.00 lb-ft* gross torque
Impeller	Welded steel
Tractor compatibility**	X500 Multi-Terrain and X700 Series Tractors
Mower compatibility	48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MC542 Material Collection System, boot and hose kits

Order number:

LP22834 - MC542 Material Collection System

LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)

LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)

LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)

LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)

LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)

LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)

LP23083 - Boot kit for 62-in. (157-cm) Mower Deck

LP39450 - MC542 Hose kit

Features and benefits:

• Fits 17P Poly Cart (not included with MC542)
• Large 53-cu ft (1.5 m3), 42-bu (1,480-L) capacity with full 83-in. (210.8-cm) clamshell opening - perfect for fall cleanup of leaves
• Powerful 205-cc, 9.00 lb-ft* gross torque engine
• Welded steel impeller for greater suction
• Large, 8-in. (20.3-cm) diameter wire embedded hose for less clogging and larger volume pickup
• Full opening for easy access
• Vented 15-oz (425-g) poly-mesh canopy that keeps dust and exhaust away from the operator
• Contoured handles for easier open/close operation and emptying
• Custom pre-cut mower boot and welded bracket assembly for easy fit to the following John Deere Mower Decks that can be ordered separately:
  • 48, 54, and 62 in. (122, 137, and 158 cm)
  • 54- and 60-in. (137- and 152-cm) HC
  • 60-in. (152-cm) 7-Iron

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.

Specifications

 

Capacity	42 bu (1500 L), 53 cu ft (1.5 m3)
Engine	205 cc, 9.00 lb-ft* gross torque
Impeller	Welded steel
Tractor compatibility**	X500 Multi-Terrain and X700 Series Tractors
Mower compatibility	48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MC542 Material Collection System, boot and hose kits

Order number:

LP22834 - MC542 Material Collection System

LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)

LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)

LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)

LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)

LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)

LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)

LP23083 - Boot kit for 62-in. (157-cm) Mower Deck

LP39450 - MC542 Hose kit

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 3-bag Power Flow MCS. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full. 

 

One chute works with several tractor applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the tractor/mower application.

 

The 3-bag hopper installs to the tractor with the Click-N-Go™ mounting system:

• Click-N-Go brackets must be ordered separately.

NOTE: The chute can be used with 48C/48X, 54C/54X, 60-in. (152-cm) 7-Iron™, 62C/62X, 62D, 54 HC, and 60 HC Mowers.

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the 2-bag Power Flow material collection system. The chute includes a convenient handle and a fill indicator that tells the operator when the bags are getting full.

One chute works with several vehicle applications. Trim lines on the chute are referenced in the instructions so the chute can be cut to the proper length for the vehicle/mower application.

The Power Flow chute is required, along with the high-performance Power Flow blower, to use the MC519 Cart MCS.

The 14-bu (493-L), 3-bag Power Flow MCS increases the versatility of the X500 Multi-Terrain Tractors and the GT and GX Series garden tractors equipped with a 48-in. (122-cm) or 54-in. (137-cm) Convertible or Edge™ Xtra mower and C-Series high-performance Power Flow blower.

The large 14-bu (493-L) capacity means the operator can collect a large area of grass or leaves before needing to stop to empty the bags.

The 7-bu (247-L) hopper provides an efficient means of collecting grass clippings and leaves using either the cut-and-throw rear bagger or the Power Flow material collection system (MCS):

• 38-in. (97-cm) and 42-in. (107-cm) mower decks use the cut-and-throw system.
• 48-in. (122-cm) and 54-in. (137-cm) mower decks use the Power Flow system.

The hopper design provides modern styling, great bagging performance, cleaner operation, and easy-to-empty bags.

The 7-bu (247-L) MCS features:

• 7-bu (247-L) capacity
• Easy-to-attach lower chute (ordered separately)
• Handle on chute
• Air exhaust duct
• Convenient spring-latch
• Airflow fill indicator
• Quik-Tatch mounting
• Sealed hopper top
• Loose-knit bags available

A loose-knit bag is available as an option for use with 7-bu (247-L) cut-n-throw rear baggers and Power Flow™ baggers:

• Two loose-knit bags are required.
• The loose-knit bag allows more air to flow through and provide more complete bag filling in wet and heavy grass conditions.

 

The MC519 is compatible with Select Series™ X320, X324, X340, X360, X380, X384, X390, X394, X500 Series Multi-Terrain, X700 Series Tractors, GT200, GX300, X400, and X500 Heavy-Duty Garden Tractors, and 110 through 455 Garden Tractors.

 

NOTE: MC519 is not compatible with D100 Series, LA100 Series, L100 Series, 100 Series, or Select Series model X300, X304, X310, X330, X350, X354, X370 Tractors, LT, LX, or SST Lawn Tractors, or G100 or G110 Garden Tractors.

 

The MC519 is designed to provide the versatility of two products in one - a utility cart or a material collector.

 

Utility cart:

• 7.5 cu ft (212 L) heaped or 500 lb (227 kg) of capacity
• Ideal for hauling topsoil, gravel, sand, firewood, mulch, etc.

 

Collector:

• Large, 19-bu (23-cu ft), (670-L) capacity with a standard equipment cover
• Can be equipped with a Power Flow blower and chute for vacuuming grass clippings, thatch, pine needles, and leaves

Potential customers include homeowners, commercial operators, nurseries, and estates.

Easy to hook up and operate

The MC519 hitch can be connected to the tractor without tools in about one minute.

 

In combination with non-jackknifing caster wheels, this semi-rigid hitch makes it easy to maneuver the cart/collector.

 

An easy-to-reach handle allows dumping the cart/collector from the tractor seat.

 

For dumping extra-heavy loads, the operator can use the hand grip on the front of the box.

A standard equipment cover can be installed in a matter of seconds to convert the utility cart to a collector:

• Large plastic window in the cover allows the operator to see when the collector is full.
• Cover folds flat for space-saving wall storage.

Strong construction

The MC519 has the durability to handle homeowner or commercial applications:

• Steel support structure is mig-welded for strength.
• Cart box is made of strong, 18-gauge, 0.05-in. (1.2-mm) steel for durability.
• Puncture-resistant 4-ply rated (PR) turf tires are standard equipment.
• Greaseable bearings (wheels and casters) enable long life.
• Cover is made of tough 14-oz (397-g) black vinyl-coated nylon. The lower sides are made of 9.5-oz (269-g) black polyester knitted cloth.

Power Flow option (Power Flow blower and discharge chute must be ordered separately)

When equipped with the optional blower and discharge chute (ordered separately), the MC519 becomes a material collection system.

The blower housing material is high-density polyethylene and the fan material is ultra-high molecular weight polyethylene:

• Lightweight for easy handling and minimal effect on mowing smoothness
• Will not rust or corrode
• Resists wear and abrasion caused by sand
• Contoured design for clean appearance and smooth grass flow

Specifications

 

Capacity
Collector
Volume	19 bu (670 L) or 23 cu ft (0.67 m3)
Load	500 lb (226.8 kg)
Cart
Volume	7.5 cu ft (0.21 m3) heaped; 6 cu ft (0.17 m3) struck
Load	500 lb (226.8 kg)
Box dimensions
Width	42 in. (107 cm)
Length	30 in. (76 cm)
Depth	8 in. (20 cm)
Overall dimensions, including hitch
Width	45.5 in. (116 cm)
Length	51 in. (129.5 cm)
Depth	44 in. (112 cm)
Clearance	10 in. (25 cm)
Dump angle	50 degrees
Weight, shipping (with carton)	176 lb (80 kg)
Weight, net
Cart only	119 lb (54 kg)
Cover only	26 lb (12 kg)
Hitch only	7.7 lb (3.47 kg)
Power Flow™ dimensions
Fan diameter	13 in. (334 mm)
Fan width	2.75 in. (70 mm), 3.75 in. (95 mm) for C Series Blowers
Fan blades	4, 5 for C Series Blowers
Fan speed	3400 (will vary with mower width)
Tires	4.10x3.50 4PR
Bearings
Wheel	Iron/Oilite™ with grease fittings
Caster	Roller ball with urethane seals and grease fittings
Box material	18-gauge, 0.05-in. (1.2-mm) steel
Cover material	14-oz (0.4-kg) black vinyl-coated nylon top, front, and upper side flaps 9.5-oz (0.27-kg) black polyester knitted cloth lower sides 0.397-sq yd (0.33-m2) knitted polyester netting

 

Oilite is a trademark of Beemer Precision Incorporated.

Tractor compatibility and requirements

 The MC519 Cart is compatible with the following tractors with 48A and 54A Accel Deep™ Decks, 38, 46, 48, 48C Convertible, 48 Edge^TM Xtra Deck, 50-, 54-, 54C Convertible, 54 Edge Xtra Deck, 60, 60-in. (152-cm) 7-Iron™, 62C Convertible, 62 Edge Xtra Deck, 54-in. (137-cm) high capacity (HC), or 60-in. (152-cm) high capacity (HC) mowers:

Requirements and/or recommendations:

1. 200 lb (91 kg) (4) cast-iron rear wheel weights are recommended for ballast on GT242, GT262, GT275, GT225, GT235, GT245, 240, 245, 260, 265, 285, 320, 325, 335, 345, 355D, GX325, GX335, GX345, GX355, X500, X520, X534, and X540 Tractors when operating on slopes. Select Series X320, X324, X340, X360, X380, X384, X390, and X394 Tractors may need ballast to increase traction, stability, or steering, especially when operating on hillsides or if carrying heavier materials in the MC519 Cart. 
2. 420 and 430 Tractors require (1) AM118915 60-in. (152-cm) Power Flow installation kit for mounting 60-in. (152-cm) Power Flow blower.
3. 316, 318, 322, 330, 332, 420, 430 require black hitch mounting bracket M115521.

Required on MC519 (S/N 045001 - ) to mount on the following Tractors:

• 316, 318, 322, 330, 332, 420, and 430
• 425 Two Wheel Steer (- A040774) without 3-Point Hitch
• 425 All Wheel Steer (- B040203) without 3-Point Hitch
• 445 (- C040542) without 3-Point Hitch
• 455 Two Wheel Steer (- C040507) without 3-Point Hitch
• 455 All Wheel Steer (- D040074) without 3-Point Hitch

This bracket was included in older MC519's but was eliminated when the 425, 445 and 455 Tractors hitch design was changed and the bracket was no longer required for hookup.

4. GT, 300 and GX 48C Mowers built before April 2002 may need 0.5-in. (13-mm) hole drilled in mower wheel bracket for installing BM20667 or BM21495 48C HP Blower. See Service Information Bulletin 02-11-45-7 for detailed instructions.

5. GT, 300 and GX 48C Mowers built after April 2002 may need slot added to mower wheel bracket for installing BM19439 and BM20523 QT Blower. See Service Information Bulletin 02-11-45-7 for detailed instructions.

6. X400/X500 HDGT's and X700 Ultimate Tractors require LP52039 Adaptor Kit for MC519 Cart, available from Order Zone.

7. X400/X500 HDGT's and X700 Ultimate Tractors with a 48C/48X Mower require BM20976 or BM22798 48 HP Adapter Kit to install BM20667 48C High-Performance Power Flow Blower Assembly to accommodate this mower's rotateable wheels:

• One BM20976 48C/48X High Performance Blower Assembly Adapter Kit is required to install the BM20667 48C HP Power Flow Blower on a 48C or 48X Mower Deck (SN -050588) with wheels that rotate.
• One BM22798 48C/48X High Performance Blower Assembly Adapter Kit is required to install the BM20667 48C HP Power Flow Blower on a 48X Mower Deck (SN 050589- ) with wheels that rotate.

8. The following older 425, 445, and 455 Tractors without a 3-point hitch also require black hitch mounting bracket M115521:

• 425 two-wheel steer (A040774 and below)
• 425 all-wheel steer (B040203 and below)
• 445 (C040507 and below)
• 455 two-wheel steer (C040507 and below)
• 455 all-wheel steer (D040074 and below)

9. BM20668 54C and BM20669 62C HP Power Flow Blowers require one AM133822 Mower Wheel Adjustment Pin for installation on 2004 and later 54C or 62C Mowers.

NOTE: In order to be used as a material collection system, an optional Power Flow blower and discharge chute must be ordered in addition to the LP49228 MC519 Material Collection System.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

MC519 Material Collection System
Order number: LP49228

Features and benefits:

• Fits 17P Poly Cart (not included with MC542)
• Large 53-cu ft (1.5 m3), 42-bu (1,480-L) capacity with full 83-in. (210.8-cm) clamshell opening - perfect for fall cleanup of leaves
• Powerful 205-cc, 9.00 lb-ft* gross torque engine
• Welded steel impeller for greater suction
• Large, 8-in. (20.3-cm) diameter wire embedded hose for less clogging and larger volume pickup
• Full opening for easy access
• Vented 15-oz (425-g) poly-mesh canopy that keeps dust and exhaust away from the operator
• Contoured handles for easier open/close operation and emptying
• Custom pre-cut mower boot and welded bracket assembly for easy fit to the following John Deere Mower Decks that can be ordered separately:
  • 48, 54, and 62 in. (122, 137, and 158 cm)
  • 54- and 60-in. (137- and 152-cm) HC
  • 60-in. (152-cm) 7-Iron

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s web site for additional information.

Specifications

 

Capacity	42 bu (1500 L), 53 cu ft (1.5 m3)
Engine	205 cc, 9.00 lb-ft* gross torque
Impeller	Welded steel
Tractor compatibility**	X500 Multi-Terrain and X700 Series Tractors
Mower compatibility	48-, 54-, 54- HC, 60- 7-Iron, 60- HC, and 62-in. (122-, 137-, 137-, 152-, 152-, and 157-cm) John Deere Mower Decks

*Per SAE J1940 as rated by engine manufacturer. The engine horsepower and torque information are provided by the engine manufacturer to be used for comparison purposes only. Actual operating horsepower and torque will be less. Refer to the engine manufacturer’s Web site for additional information.
**For proper braking and operation, the loaded weight of the collection system should never
exceed the weight of the tractor, or other towing unit, plus the operator. Additional ballast on
the tractor, or other towing unit, may be needed to meet this requirement.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MC542 Material Collection System, boot and hose kits

Order number:

LP22834 - MC542 Material Collection System

LP23080 - Boot kit for 48-in. (122-cm) Mower Deck (48X)

LP65063 - Boot kit for 48-in. (122-cm) Mower Deck (48A)

LP65064 - Boot kit for 54-in. (137-cm) Mower Deck (54A)

LP23081 - Boot kit for 54-in. (137-cm) Mower Deck (54X)

LP44079 - Boot kit for 54-in. (137-cm) Mower Deck (54 HC)

LP23082 - Boot kit for 60-in. (152-cm) Mower Deck (60 HC and 7-Iron™ 60D)

LP23083 - Boot kit for 62-in. (157-cm) Mower Deck

LP39450 - MC542 Hose kit

Dump from the seat capability for 3-bag material collection systems (MCS)

The MCS 14 attachment is designed to provide dump-from-seat grass collection and expulsion for all John Deere 3-bag material collection systems (MCS) on the X500 and X700 Series Tractors. The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.

The aluminum body is light weight and easy to handle. A conveniently located lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere material collection system, installation is a breeze with simple hand tools.

Features:

• Lightweight aluminum construction
• Designed for full material expulsion
• Easy access self-latching, spring-tripped handle
• Ships almost fully assembled (5 minute handle assembly)
• Installs in seconds (after initial assembly)

Benefits:

• Easy - Convenient access to dump handle directly from seat 
• Clean - No material handling, no mess 
• Efficient - Unload and go without leaving the seat

NOTE: Fits John Deere 3-bag material collection systems on X500 and X700 Series Tractors.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MCS 14 attachment
Order number: LP47170

Dump from seat capability for X500 and X700 Series 2-bag material collection systems (MCS)

The MCS 8 attachment is designed to provide dump from the seat grass collection/expulsion for all John Deere X500 and X700 Series tractors equipped with the 2-bag material collection system (MCS). The MCS attachment eliminates the need to get off of the tractor and empty the bags. As a result, it will increase both efficiency and cleanliness in the mowing process.

The aluminum body is lightweight and easy to handle. Conveniently located hand lever and smooth release and latching system are easily accessed from the tractor seat. Because it is engineered specifically for the John Deere MCS, installation is a breeze with simple hand tools.

Features:

• Lightweight aluminum construction
• Designed for full material expulsion
• Easy access self-latching spring-tripped handle
• Ships almost fully assembled (5 minute handle assembly)
• Installs in seconds (after initial assembly)

Benefits:

• Easy - Convenient Access to dump handle directly from seat 
• Clean - No material handling, no mess 
• Efficient - Unload and go without leaving the seat 

NOTE: Fits All John Deere X500 and X700 Series 2-bag material collection systems. Not compatible with EZtrak™ Zero-Turn Mowers.

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

 

MCS 8 attachment
Order number: LP47169

The high-performance (HP) Power Flow blower assembly for the 48-in. (122-cm) Accel Deep™ Mower is used with the hopper and chute to provide a very effective material collection system. A hopper and chute must be ordered separately to complete this material collection system.

The high-performance (HP) Power Flow blower assembly for the 54-in. (137-cm) Accel Deep™ Mower is used with the hopper and chute to provide a very effective material collection system. A hopper and chute must be ordered separately to complete this material collection system.

One 30-lb (13.6-kg) cast-iron weight may be installed on each front wheel for additional stability when operating on hillsides or with heavy rear equipment.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front wheel weights are not available for special-edition tractors because the styled front  wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.

One or two 50-lb (22.7-kg) cast-iron weights may be installed on each rear wheel to provide extra traction and stability.

Features include:

• Weights are made of durable cast iron and painted John Deere yellow.
• Weights may be installed with the wheel in either the narrow or wide position.
• These weights may be used on both two-wheel-steer and all-wheel-steer tractors.
• To stack the weights and install two on a wheel, two 1/2x8-in. (12.7x203-mm) bolts are required per wheel (not furnished).
• X700 Special Edition Tractors (model year 2012 and prior) and X738, X739, and X758 Signature Series Tractors require a BM21497 wheel weight adapter ring on each rear wheel on which weights are to be installled.

NOTES:

1. Plastic rear wheel weight comes with necessary hardware for installation.
2. X Series Special-Edition Tractors require an additional BM21497 special-edition weight adapter for each rear wheel on which weights are to be installed.

For 50-lb (22.7-kg) cast-iron wheel weights on 23x10.50-12 or 24x12-12 rear tires:

 

BM17985 - for mounting one 50-lb (22.7-kg) weight

BM17977 - for mounting two 50-lb (22.7-kg) weights

For 50-lb (22.7-kg) cast-iron wheel weights on 26x12-in. rear tires:

 

BM17977 - for mounting one 50-lb (22.7-kg) weight

BM18101 - for mounting two 50-lb (22.7-kg) weights 

For 70-lb (32-kg) starter cast-iron wheel weight on 26x12-12-in. rear tires:

 

BM18089 - for mounting 70-lb (32-kg) starter weight

For 70-lb (32-kg) starter and 50-lb (22.7-kg) cast-iron weight(s):

 

BM17977 - for mounting one 70-lb (32-kg) starter and one 50-lb (22.7-kg) weight

BM18101 - for mounting one 70-lb (32-kg) starter and two 50-lb (22.7-kg) weights

A - one (1) UC13499 and one (1) BM17972 weight
B - one (1) UC13499 and two (2) BM17972 weights

Four-wheel-steer tractors

NOTE: Plastic wheel weight is not compatible with four-wheel-steer tractors.

For 50-lb (22.7-kg) cast-iron wheel weight on 26x10.50-12 tires:

 

BM18094 - for mounting one 50-lb (22.7-kg) weight

BM17977 - for mounting two 50-lb (22.7-kg) weights

NOTES:

1. Plastic rear wheel weight comes with necessary hardware for installation.
2. X Series Special-Edition Tractors require an additional BM21497 special-edition weight adapter for each rear wheel on which weights are to be installed.

For 50-lb (22.7-kg) cast-iron wheel weights on 23x10.50-12 or 24x12-12 rear tires:

 

BM17985 - for mounting one 50-lb (22.7-kg) weight

BM17977 - for mounting two 50-lb (22.7-kg) weights

For 50-lb (22.7-kg) cast-iron wheel weights on 26x12-in. rear tires:

 

BM17977 - for mounting one 50-lb (22.7-kg) weight

BM18101 - for mounting two 50-lb (22.7-kg) weights 

For 70-lb (32-kg) starter cast-iron wheel weight on 26x12-12-in. rear tires:

 

BM18089 - for mounting 70-lb (32-kg) starter weight

For 70-lb (32-kg) starter and 50-lb (22.7-kg) cast-iron weight(s):

 

BM17977 - for mounting one 70-lb (32-kg) starter and one 50-lb (22.7-kg) weight

BM18101 - for mounting one 70-lb (32-kg) starter and two 50-lb (22.7-kg) weights

A - one (1) UC13499 and one (1) BM17972 weight
B - one (1) UC13499 and two (2) BM17972 weights

Four-wheel-steer tractors

NOTE: Plastic wheel weight is not compatible with four-wheel-steer tractors.

For 50-lb (22.7-kg) cast-iron wheel weight on 26x10.50-12 tires:

 

BM18094 - for mounting one 50-lb (22.7-kg) weight

BM17977 - for mounting two 50-lb (22.7-kg) weights

The 42-lb (19-kg) Quik-Tatch can be used to counterbalance a heavy front or rear attachment and/or provide greater stability, especially when operating on hills.

This weight is constructed of cast iron and weighs approximately 42 lb (19 kg).

Some vehicles have built-in front and/or rear weight brackets to hang the weights on; others require a weight bracket that must be ordered separately.

X400/X500 Heavy-Duty Garden Tractors and X700 Series Tractors require the following parts when weights are installed on the front of the tractor:

• One  M147986 weight retaining rod (Parts)
• Two  M40461 spring clip (Parts)

Rear weight bracket is designed to hold two suitcase weights on X300 Tractors and up to four suitcase weights on X500 Multi-Terrain Tractors.

• This item required for 4-wheel-steer tractors only; weight bracket is built into frame of 2-wheel-steer tractors.
• It is particularly useful to counterbalance a front-mounted attachment such as a snow blower or blade.
• Weight bracket can be quickly mounted to the rear of the tractor.
• Weight bracket will not interfere with rear grass bagger mounting bracket.

Hardware is required for installing each front-wheel weight.

Requirements:

• Mounting may require drilling two holes in the wheel rim.
• BM17978 mounting hardware kit is required for each weight.

NOTE: Front-wheel weights are not available for special edition tractors because the styled front-wheel design does not have appropriate holes for mounting the wheel weights and no adapter is available.

M152726 is an approved alternative to M143520, standard side-discharge blade. M152726 improves cut-quality performance in certain grass conditions. It will increase the amount of lift or suction under the deck. It will be most beneficial for customers who are experiencing cut quality issues with the standard blade, especially in limp grass, typical in early spring and late fall. The blade will improve side-discharge performance, but a potential downside is increased blow-out in dry conditions.

The BM26238 dry-condition kit, 48A is available for 48A Accel Deep Mower Decks used on model year 2016 and later X300 and X500 Select Series™ Tractors and Residential ZTrak™ Mowers. The 48A dry-condition kit will also work with any X700 Signature Series Tractor (model year 2013 and later) that is equipped with a 48A Mower Deck.

The dry-condition kit will reduce the amount of blowout around the mower deck when side discharging, mulching, or bagging in dry grass and leaf conditions. For optimum mowing performance in lush-grass conditions, the dry-condition kit baffles may be removed.

Features and benefits

• Homeowners can now achieve results just like the professionals
• Brush is easy to adjust for varying mower cutting height
• Brush adjusts to varying ground conditions and allows the operator to freely maneuver the vehicle without damaging the turf
• The brush striping kit is a very economical and functional attachment

Compatible with the following:

• 48A or 54A - 48-in. (122-cm) or 54-in. (137-cm) Side-Discharge Mower for X350, X354, X370, X380, X384, X390, X394, X570, X580, X584, and X590 (model year 2016) Tractors

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

48A or 54A - 48-in. (122-cm) and 54-in. (137-cm) grass groomer

Order number: LP63761

Leveling gauge allows quick and accurate mower deck leveling and cutting height adjustment.

Can be used for:

• Lawn tractors
• Lawn and garden tractors
• Riding mowers
• Front mowers
• Commercial walk-behind mowers
• Zero-turn-radius mowers

MulchControl advantages and benefits

The MulchControl attachment for the 48A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The MulchControl baffle, or divider, between the left and middle spindles is about half way down. The height is designed to balance the mulching and side-discharge modes.
  • When the MulchControl baffle is open, the divider between the left and middle spindles passes a portion of the material to the discharge opening, along with the material from the middle and right spindle areas.
  • When the MulchControl baffle is closed, this material stays within the deck and gets chopped into mulch and deposited in the turf.

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
  • The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

MulchControl limitations

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses, such as Zoysia and Bermuda
• When cutting in wet, high-growth conditions, such as those found in the Pacific Northwest United States
• When optimum bagging and lawn clean-up is desired

MulchControl advantages and benefits

The MulchControl attachment for the 54A Mower Deck makes mulching more practical for many mowing situations because it not only does an excellent job of mulching but it also allows the mower to be easily converted for times when it is more desirable to side discharge or collect the lawn material. Advantages of mulching grass clippings include:

• A beautiful looking lawn
• Grass clippings not blown onto the operator, driveways, or flower beds
• Less fertilizer use
• Elimination of the effort needed to dispose of clippings

How MulchControl works

MulchControl is an innovative, simple design that is easy to use and maintain:

• The MulchControl attachment includes baffles to control the flow of material under the deck.
  • The MulchControl baffle, or divider, between the left and middle spindles is about half way down. The height is designed to balance the mulching and side-discharge modes.
  • When the MulchControl baffle is open, the divider between the left and middle spindles passes a portion of the material to the discharge opening, along with the material from the middle and right spindle areas.
  • When the MulchControl baffle is closed, this material stays within the deck and gets chopped into mulch and deposited in the turf.

• The MulchControl handle is located on top of the mower deck and used to open and close the discharge baffle.
  • The operator is required to get off of the machine in order to engage or disengage mulch mode.
• Changing from mulching to side discharge or vice versa takes only a few seconds.

MulchControl is well-suited to the following mowing situations:

• Usually mulch, but side discharge when grass gets too long
• Usually side-discharge, but would like to be able to close the chute to control clippings
• Always mulch a main lawn, but often side discharge secondary lawns
• Bag clippings, but want to go farther before emptying bags

MulchControl puts the operator in control of the clippings. Now the operator can have all the benefits of mulching with the ability to easily change to side discharge or bagging when needed.

MulchControl limitations

While in the side-discharge mode, MulchControl will still mulch about one third of the material. Therefore, the side-discharge mode is essentially a partial-mulch mode. This can be an advantage when side discharging or bagging, as it helps to reduce the amount of material being discharged. Other times this could work as a disadvantage:

• When cutting strong southern grasses, such as Zoysia and Bermuda
• When cutting in wet, high-growth conditions, such as those found in the Pacific Northwest United States
• When optimum bagging and lawn clean-up is desired

The brush guard adds a distinctive appearance to the tractor and protects the front of the tractor from damage.

By removing one spring clip and pin, the brush guard may be lowered to permit opening the hood.

Cover provides heavy-duty protection for Select Series™ X300, X500, and X700 Tractors.

Features include:

• Wipe-clean reinforced bottom around mower deck
• Easy-on side handles makes snugging down cover a snap
• Dual reinforced air vents let air circulate and help prevent ballooning in wind
• Interior lining and integrated muffler heat shield
• Heavy-duty fabric will not shrink or stretch and is coated for maximum water resistance
• Easy-on split back for fast fitting and easy access after installation
• Handy storage pocket reverses into an attractive storage case
• Two-year warranty

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

Protective cover (large deluxe)

Order number: LP93647

Features include:

• Dual vents let air circulate and help prevent ballooning in wind
• Elastic shock cord in bottom hem for a quick, custom-like fit
• Coated fabric for maximum water protection
• One-year warranty

Cover provides all-season protection for 100 Series, S240 Sport and Select Series™ X300 Series Tractors.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

 

Protective cover (standard)

Order number: LP93917

The integral hitch permits the use of certain rear-mounted equipment, such as a cultivator, disk harrow, plow, or box scraper/blade attachment.

Key features include:

• Lifts/lowers using included mechanical hand-operated lever
  • Provides reasonable lift efforts
• Uses one pin and spring clip for installation or removal
• May be installed at the same time as the mower, front blade, or snow thrower
• Can install 42-lb (19-kg) Quik-Tatch™ suitcase weights for ballast when using the integral hitch
• Compatible with GT and GX garden tractors and X500, X520, X530, X534, X540, X570, X580, X584, and X590 Multi-Terrain Tractors

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

Integral hitch

Order number: LP31357

The 21-in. (53.3-cm) professional two-piece seat, four-bar suspension, and slide shipped on Signature Series X700 Tractors is available as an upgrade seat and suspension for all X500 Multi-Terrain Tractors (model year 2006-). Key selling features for this seat include:

• Thick seat cushion for lasting comfort, even after a full day of use
• Back of seat can be angled to maximize operator comfort
  •  Convenient lever on the side of the seat unlocks back of seat to allow positioning
• Four-bar suspension and slide are included for extra comfort and bolt to the tractors fender-deck mounting holes
• BM24426 armrest attachment available as a field-installed option

Optional armrest attachment

Armrests increase operator support and comfort, thus reducing fatigue and improving productivity, especially when mowing for extended periods of time. Armrests are adjustable to suit the operator. This armrest attachment is designed for the 21-in. (53.3-cm) professional two-piece seat.

Compatibility

BM25346 21-in. (53.3-cm) professional two-piece seat, four-bar suspension, and slide is a field-installed attachment and compatible as follows:

• All Select Series™ X500 Series Multi-Terrain Tractors, model year 2006 and later

Spark arrester is available to meet the law in the State of California requiring use of a spark arresting muffler under certain conditions.

Applies in other states and Canada when needed to comply with local ordinances or customer requests.

NOTE: This law basically requires that purchasers of certain products be given written notice that it is illegal to use such machines on forest-covered, brush-covered, or grass-covered land (except watered lawns) without a spark arrester. For further information on this law, consult No. 4442.5 of the California Public Resources Code.

Features and benefits:

• 100-psi (689-kPa) SHURflo® diaphragm-type pump is designed for high-hour commercial applications; it can be run dry without damage.
• It is easy to assemble the custom mounting brackets.
  • Brackets use the existing frame holes.
• Brass-tipped spray wand is included as standard equipment; it is constructed of noncorrosive polypropylene material with Viton® components for multi-use applications.
• Check valves in the boom tips prevent siphoning and dripping, which can cause lawn spotting.
• Control valve directs spray to either the boom or spray wand for added convenience
  and versatility.
• Electrical hookup is simple with a convenient on/off switch.
• Sprayer contains a rugged translucent-yellow tank with molded fill-level indicators (in gallons).
• It is only a 15-second no-tools mounting after assembly.

Specifications

Item number	LP22861
Tank capacity	25 gal. (95 L)
Boom	60-in. (152.4-cm) boom, 90-in. (228.6-cm) spray
Spray wand reach	30 ft (9.1 m)
Hose length	19 ft (8 m)
Shipping weight	35 lb (16 kg)
Warranty	2-year consumer warranty

Ordering information

Please contact your local John Deere dealer for availability and pricing information.

25-gal. (95-L) Mounted Sprayer for X300 and X500 Tractors

Order number: LP22861

SHURflo is a trademark of SHURflo, LLC.

Viton is a trademark DuPont Performance Elastomers.

The 45-gal. (170-L) HP Tow-Behind Sprayer offers the ultimate in performance and versatility. With its large-capacity, high-volume electric pump, and premium pistol-grip spray gun, it provides an excellent way to apply spray materials such as liquid fertilizer, weed killer, tree spray, and de-icer. It is the perfect match for the operator who wants extreme performance. 

The heavy-duty frame rolls smoothly on 15x6 tires that minimize ground compaction and have a low profile, which maintains a low center of gravity for excellent stability. Cover ground quickly with flexible boom options; a 150-in. (381-cm) precision folding, 24-ft (7.3-m) boomless, or no boom at all (boom sold separately).

HP features:

• 100-psi, 4.0-gpm (15-L/min) diaphragm-type pump is designed for high-hour applications and can be run dry without damage
• Redesigned frame cuts assembly time by 20 minutes coompared to previous models
• Booms (sold separately) ship pre assembled
• Premium pistol-grip spray gun, designed for single-hand mist to 35-ft (10.7-m) stream
• Front-mount hose tender for easy hose access and storage
• Glycerin-filled pressure gauge
• TeeJet™ pressure regulation/recirculation valve
• Includes sprayer remote control

Additional features

• Easy boom removal for added convenience
• Control valve channels spray to either the boom or spray wand
• Rugged translucent yellow tank with molded fill-level indicators (in gal.)

Boom options (sold separately):

• 150-in. (381-cm) precision spray boom
• 24-ft (7.3-m) boomless spray nozzles

Ordering information

Please contact a local John Deere dealer for availability and pricing information.

45-gal. (170-L) HP Tow-Behind Sprayer
Order number: LP39963

TeeJet is a trademark of Spraying Systems Company.

Sprayer comes complete with a boom that sprays 60 in. (152.4 cm) wide. It also has a 12-ft (3.7-m) hose with an adjustable handgun for spot spraying lawns, shrubs, etc.

Features include:

• This sprayer is an excellent choice for spraying small- to moderate-size lawns and shrubs.
• Handgun with adjustable spray pattern is helpful when spraying fruit trees and can be used to spray trees up to 30-ft (9.1-m) high.
• A 14-in. (35.6-cm) wand on the handgun is standard equipment to give added convenience when spraying trees.

NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).

This sprayer is especially suited for maintaining residential and small commercial properties:

• Sprayers provide an excellent way to apply liquid fertilizer.
• Herbicides and pesticides can be applied along with liquid fertilizer or separately.

Advantages of using liquid fertilizer over dry fertilizer:

• Fertilizer is more readily available to plants.
• The fertilizer need not be worked into the soil by watering or rain before it will work.
• Herbicides are more effective when applied with liquid fertilizer.

NOTE: Use these sprayers with liquid-base lawn care chemicals only. They are not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

15-gal. (57-L) Tow-Behind Sprayer

Order number: LP19478

Sprayer comes with a wider boom that sprays a 90 in. (228.6 cm) width. A 15-ft (4.6-m) hose and handgun are provided.

Features include:

• 100 psi Shurflo® diaphragm-type pump is designed for high hour commercial applications. It can be run dry without damage.
• Sprayer is designed to be a good choice for customers with larger lawns with trees to care for or for light commercial spraying.
• Handgun with adjustable spray pattern is helpful when spraying fruit trees and can be used to spray trees up to 30 ft (9.1 m) in height.
• The 14-in. (35.6-cm) wand on the handgun is included as standard equipment.

NOTE: Sprayers are compatible with competitive tractors (if equipped with a 12-V battery and charging system).

This sprayer is especially suited for maintaining residential and small commercial properties.

• Sprayers provide an excellent way to apply liquid fertilizer.
• Herbicides and pesticides can be applied along with liquid fertilizer or separately.

Advantages of using liquid fertilizer over dry fertilizer:

• Fertilizer is more readily available to plants.
• The fertilizer need not be worked into the soil by watering or rain before it will work.
• Herbicides are more effective when applied with liquid fertilizer.

NOTE: Use this sprayer with liquid-based lawn care chemicals only. It is not recommended for wettable powders as no agitating system is provided to prevent particles from separating out.

Ordering information

Customers, please contact your local John Deere dealer for availability and pricing information.

25-gal. (95-L) Tow-Behind Sprayer

Order number: LP19479

SHURflo is a trademark of SHURflo, LLC.