- Specialty Tractors (75-155 Engine HP)
- Utility Tractors (22.4 - 140 Engine HP)
- Utility Tractor Attachments & Implements
- Home & Workshop Products
The desired swath width can easily be obtained by loosening the handle on each side and moving the adjustable swath deflectors to the desired position. Swath width is adjustable from 1.4 m to 2.0 m (4 ft, 7 in. to 6 ft, 6 in.) on the 131 Front-Mounted Mower-Conditioner.
The available room for a windrow is a function of wheel spacing and tire width. The windrow width of the 131 Front-Mounted Mower-Conditioner may be narrower than the windrows from a 388 Twin Rear-Mounted Mower-Conditioner if the forming shields are adjusted so the tractor does not drive on the windrow that is produced.
A wide spread kit is available as a field-installed bundle. This kit is composed of vanes installed under the conditioning hood. The crop flow is spread to approximately the machine working width and offset about 400 mm (15.75 in.) on the left-hand side. This allows a clean separation between the uncut crop and spread crop.
The Model 131 Front-Mounted Mower-Conditioner is used to maximize the potential of the 7R or 8R Tractor equipped with a front PTO. This 1000-rpm mower-conditioner can be combined with the following 1000-rpm mower-conditioners to increase productivity:
Unmatched productivity is gained with cutting widths up to nearly thirty feet in one pass along with a narrow transport width.
The A-frame adapter enables quick and easy installation of the 131 Front-Mounted Mower-Conditioner. The adapter attaches to the tractor’s front 3-point hitch and locks into the mating headstock that is part of the mower-conditioner.
Down stop chains are include for use with tractors, such as the 8R, without front hitch position sensing. A front chain support kit (RE327692) is required to connect the down stop chains on an 8R Tractor.
The 7R Tractors are equipped with position sensing that has the ability to establish front hitch set points from the CommandCenter™. Position sensing will maintain the height of the hitch arms based on the set point.
The front chain support kit (RE327692) is not required for 7R Tractors, but damage to the front PTO driveshaft can occur if the front hitch positioning is not set correctly, or if the set point is manually overridden.
Hydraulic cylinders are used to raise and lower the cutting platform when crossing headlands.
The mower-conditioner is equipped with 54 free-swinging, steel impeller tines. This John Deere conditioner provides excellent conditioning performance and fluffy windrows.
Impeller conditioning is standard equipment on all John Deere mower-conditioners.
Proper conditioning in a wide range of crops can be achieved when the conditioner is properly adjusted.
The impeller conditioner works well in legumes, especially alfalfa and most all-grass crops. Impeller conditioners are not recommended for thick-stemmed or cane-type crops, such as sudan or sudex, or crops over 5-ft tall.
The speed at which the tines rotate will also affect the degree of conditioning. Two impeller speeds can be achieved by interchanging the upper sheave and the lower sheave.
Power is transmitted from the 1000-rpm PTO on the front of tractor through gearcases to the cutterbar.
Power is transmitted to the rotary disks through fully enclosed gears, running in oil, for quiet, smooth, reliable operation
|Select up to 4 models to compare specifications||
Front Mount Mower-Conditioner
|PTO speed||1,000 rpm|
|HP 540 rpm PTO|
|HP 1000 rpm 1-3/8 in. PTO||75 kW
|HP 1000 rpm 1-3/4 in. PTO||75 kW
|Hydraulic pressure required|
|Cutting width||3.1 m
|Cutting height||30-80 cm
|Number of disks||8|
|Number of knives||16|
|Disk speed||2,986 rpm|
|Knife tip speed|
|Lubrication||GL-5 Gear Lubricant|
|Oil reservoir capacity||2.25 L
0.59 U.S. gal.
|Cutterbar oil check||Fill plug|
|Angle adjustment||Tractor center link|
|Cutterbar protection||Shear shaft|
|Adjustable gauge shoes|
104 in.Number of V-tines
54Number of speeds
Belt and sheavesConditioner hood
|Standard hitch||Tractor front hitch|
|Ball joint equal angle hitch|
|Rockshaft swivel hitch|
|Drawbar swivel hitch|
|Weight||With impeller conditioner
|Are wrenches required for adjusting?||Float
Save $1,320† with purchase of New Eligible John Deere Hay Tools or Eligible Tractors.
†For complete details regarding this offer, please select the corresponding link below.
0% APR for 48 Months† on New John Deere Hay & Forage Mower-Conditioners.
†For complete details regarding this offer, please select the corresponding link.