F350MFront Mount Mower
- Use front hitch for maximum productivity
- High-speed rotary disc cutterbar for cutting in tough conditions
Features
Expand All
Collapse All
8R Tractor front hitch
8R Tractor front hitch
The 3.5-m (11.5-ft) wide cutterbar
Quick-change knives (QCK) technology
Turnbuckle adjustment
Use front hitch for maximum productivity
Tractor hookup
8R Tractor front hitch
8R Tractor front hitch
The F350M Front-Mounted Mower is used to maximize the potential of the 7R or 8R Tractor equipped with a front power take-off (PTO) and front hitch. This 1000-rpm mower can be combined with the following 1000 rpm mower to increase productivity:
- Twin rear-mounted mower
Unmatched productivity is gained with cutting widths up to 9.9 m (32.5 ft) in one pass along with a narrow transport width.
The A-frame adapter enables quick and easy installation of the F350M Front-Mounted Mower. The adapter attaches to the tractor’s front 3-point hitch and locks into the mating headstock that is part of the mower.
- Enables easy attaching/detaching of front-mounted mower
Down stop chains can be used for tractors without front-hitch position sensing. If tractor has front-hitch position sensing, stop chains are not recommended.
- All 7R Tractors have position sensing and do not require stop chains.
- MY11-13 8R Tractors do not have position sensing and require stop chains.
- MY13+ 8R Tractors have position sensing and do not require stop chains.
The 7R Tractors are equipped with position sensing that has the ability to establish front hitch set points from the CommandCenter™ controls. Position sensing will maintain the height of the hitch arms based on the set point.
Hydraulic cylinders are used to raise and lower the cutting platform when crossing headlands.
- Front tractor hitch is not used to raise and lower the cutting platform.
- Uses single-acting selective control valve (SCV) to raise platform.
- Lift cylinder operation must be independent of the front hitch operation.
High-speed rotary disc cutterbar for cutting in tough conditions
The 3.5-m (11.5-ft) wide cutterbar
Quick-change knives (QCK) technology
Large farms, machinery rings and contractors need high quality output, and ease of serviceability.
- The cutterbars are fast mowing, with high quality work and reliable set-up.
- Each disc is protected against heavy shocks with a shear point located on the disc drive.
- All modules and intermediate gears are quickly and easily interchangeable.
To meet high quality output, the cutterbar is an oil-immersed, gear-driven cutting bed.
- All discs are offering an orbital cutting diameter of 440 mm (17.3 in.).
- With seven discs, the cutting width will be 3.1 m (10.2 ft). With eight discs, the cutting width will be 3.5 m (11.5 ft).
- Disc speeds are 2986 rpm.
To meet serviceability, the cutting bed is lubricated for life:
- No oil changes necessary.
- Discs are fitted with quick change knives technology.
- Cutting height is from 35 to 85 mm (1.4 to 3.3 in.).
Time needed to change a knife is below 15 seconds. It is an efficient way to gain up to 30 minutes of maintenance time on the mower conditioners.
Turnbuckle adjustment
Cutting height is adjusted by changing the turnbuckle on the front hitch. Cutting range is from 35 mm to 85 mm (1.4 in. to 3.3 in.).
Specs & Compare
| Specs & Compare | ||||
|---|---|---|---|---|
| John Deere F350M Front Mount Mower |
Key Specs
| PTO speed | 540 rpm | |||
|---|---|---|---|---|
| 1000 rpm 1-3/8 in. PTO | ||||
| 1000 rpm 1-3/4 in. PTO | ||||
| Powerline type | ||||
| Standard hitch | Clevis | |||
| Optional hitch | Equal angle | |||
| Hydraulic pressure required | 13,790 kPa 2,000 psi |
|||
| Cutterbar - cutting width | 2.4 m 8.1 ft |
|||
| Number of disks/knifes | 5 10 |
|||
| Transport width | 2.4 m 8.1 ft |
Power requirements
| PTO speed | 540 rpm 1000 rpm |
|||
|---|---|---|---|---|
| 540 rpm PTO | 55-75 hp 41-56 kW |
|||
| 1000 rpm 1-3/8 in. PTO | ||||
| 1000 rpm 1-3/4 in. PTO | ||||
| Powerline type |
Tractor equipment
| Tractor connection | 21 spline | |||
|---|---|---|---|---|
| Standard hitch | Clevis | |||
| Optional hitch | Equal angle | |||
| Hydraulic pressure required | 13,790 kPa 2,000 psi |
|||
| Hydraulic connections |
Cutterbar
| Type | John Deere | |||
|---|---|---|---|---|
| Cutting width | 2.4 m 8.1 ft |
|||
| Cutting height | 2.8-9.8 cm 1.1-3.8 in. |
|||
| Number of disks | 5 | |||
| Number of knives | 10 | |||
| Bolted knives | ||||
| Disk speed | 2,650 rpm | |||
| Knife tip speed | 307 km/h 191 mph |
|||
| Disk drive | Gear | |||
| Lubrication | Hy-Gard oil | |||
| Oil reservoir capacity | 5.7 L 6 U.S. qt |
|||
| Cutterbar oil check | Combination check, drain plug | |||
| Cutterbar angle | ||||
| Angle adjustment | Manual or hydraulic | |||
| Angle range | 2-8 degree (angle) | |||
| Cutterbar protection | ShearHub | |||
| Adjustable gauge shoes | Yes | |||
| Suspension system |
Impeller conditioner
| Width | 140 cm 55.2 in. |
|||
|---|---|---|---|---|
| Diameter | 59.4 cm 23.4 in. |
|||
| Tines type | V-tines | |||
| Number of tines | 33 | |||
| Number of speeds | Two | |||
| Drive | 3-V powerband belt and sheaves | |||
| Conditioner hood | ||||
| Wide spread |
Rolls conditioner
| Width | ||||
|---|---|---|---|---|
| Diameter | ||||
| Type of material | ||||
| Design | ||||
| Speed | ||||
| Drive | ||||
| Windrow width |
Dimensions
| Transport width | 2.4 m 8.1 ft |
|||
|---|---|---|---|---|
| Overall length | ||||
| Transport length | 6.2 m 20.6 ft |
|||
| Weight, roll conditioner | ||||
| Weight, impeller conditioner | 2,027 kg 4,470 lb |
|||
| Standard tires | 11L-15 standard, 31x13.5L 15 optional 31x13.5L 15 optional |
General
| Are wrenches required for adjusting? |
|---|
Additional information
| Date collected | August 24, 2020 |
|---|
-
C300 Mower-Conditioner -
C350 Mower-Conditioner -
C400 Mower-Conditioner -
C450 Mower-Conditioner -
C500 Mower-Conditioner -
F310R Front Mount Mower-Conditioner -
F350M Front Mount Mower -
F350R Front Mount Mower-Conditioner -
R870R Rear Mount Mower-Conditioner -
R950R Rear Mount Mower-Conditioner -
R990M Twin Rear Mount Mower -
R990R Rear Mount Mower-Conditioner -
S250 Mower-Conditioner -
S300 Mower-Conditioner -
S350 Mower-Conditioner
Shop and Buy
Maintenance and Support
You May Also Be Interested In
Product features are based on published information at the time of publication. Product features are subject to change without notice. Contact your local John Deere dealer for more information.
Images of equipment models may be digitally or AI generated, are for illustration purposes only, and are subject to change. Equipment models shown are typically base models and may not reflect the actual product, features, options, or attachments. Equipment availability may be limited. See your John Deere dealer for additional information.